• Proceedings of the KIEE Conference
• /
• 1995.11a
• /
• pp.296-298
• /
• 1995

This paper proposes a new filter topology that suppresses the high voltage gradient(dv/dt) in ac motor terminals. The high voltage gradient(dv/dt) causes over voltages on the motor windings, the degradation or motor insulation, and the bearing failure. Moreover surge voltage with high voltage gradient(dv/dt) in the PWM inverter red drive system where long line cables are required causes more serious problem to the motor. Thus, the most advisable method is attaching output filter to the inverter output terminals. The conventional output filters have several problems such as bulky size, difficulty or parameter tuning. The proposed filter can be relatively smaller than the conventional filters. By the proposed filter, the shaping or PWM waveform can considerably suppress high dv/dt in motor feeding cable from the inverter. The effectiveness or the proposed filter is compared with that or the conventional one and is verified by the computer simulation.

• Journal of Mechanical Science and Technology
• /
• v.17 no.5
• /
• pp.647-653
• /
• 2003

An important class of short-fiber reinforced composites is the sheet molding compound, which is recently developed and currently used in many engineering applications. Fatigue failure of the composites is a subject of major concern in design and cyclic crack propagation is of particular significance in the fatigue life prediction of short fiber composites. However, research on the fatigue behavior of polymer injection weld, especially short glass fiber-filled polymer injection weld, has not been carried out. In this study the analyses of the fatigue crack growth behaviors at weld line and in the bulk are performed based on low cycle fatigue test.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.938-942
• /
• 2008

To detect the failures in machine, the signals of current, vibration and acoustic emission are widely used in industry. And unexpected failures of gears are not only extremely damaging but also lead to economic losses. In this paper, to detect the misalignment occurred at between two gears in gearboxes, the signals of current, vibration and AE were measured at gearbox and motor power line. FFT(Fast Fourier Transform) was used for current and vibration signal analysis to find gear failure frequency. Especially, the envelop analysis and wavelet transform were applied for AE signal. Therefore, compared with the results of three kinds of signal, the possibility of earily detection by AE is identified or checked.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1303-1308
• /
• 2008

In this study, we researched how to estimate life-stress relationship and acceleration factor through performing accelerated life test and analyzing it. The purpose of this study is to predict life of pneumatic cylinder within short time which is widely used in automation manufacturing line. In design of accelerated life test, we selected operating pressure and load that have the most influence on main failure mode of pneumatic cylinder as accelerated factor. We used two-way factorial design for arranging of test condition to accelerated factor and accelerated level.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.12
• /
• pp.1123-1131
• /
• 2008

This paper provides V-factor estimation under combined mechanical and thermal load for circumferential cracks. Results are based on finite element analyses and effect of types and magnitudes of the thermal stress, crack geometry, the loading mode and plastic strain hardening on variations of the V-factor are investigated. The results of finite element analyses are compared with R6 values. As a result, it is shown that R6 gives generally conservative results. The conservatism is especially increased for the combination of large mechanical and thermal load. As a result, new estimation method which uses failure assessment line in R6 is proposed for V-factor and gives less conservative results.

• Journal of Contemporary Eastern Asia
• /
• v.10 no.1
• /
• pp.55-71
• /
• 2011

China has been experiencing high economic growth along with massive change in its industrial structure. How will the industrial structure change affect the Chinese economy? Similar changes were observed by Japan, when the Japanese banking system fell into a structural failure in terms of the inability to respond to the paradigm shift from "catching up" to "frontier economy." This paper is undertaken to highlight the lessons that China can learn from Japan's prolonged financial slump. We point out that big cities in China have already shifted to frontier economy and major provinces are on the same trend. We argue that in spite of economic reform reshaping the Chinese banking system, the financing pattern of state owned commercial banks (SOCB) is not in line with the industrial change. The Chinese banking system should be overhauled or transformed to respond to the increasing uncertainty along with the paradigm shift. Otherwise, China may fall into the same dilemma that Japan had faced in its industrial structure change.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.914-919
• /
• 1998

A Capacitor Commutated Converter (CCC) has less difficulty of commutation failure in comparison to the conventional line commutated converter. This paper proposes the Ar1R control of the CCC in the inverter operation, which deserves as the Ar1R of the conventional converter. The CCC can be operated in high power factor area by using the proposing Ar1R control. The voltage stability at an AC bus connected the CCC inverter is investigated and estimated its ability of preventing the AC voltage collapse. To estimate the voltage stability, this paper developed the simplified converter mathematical model and led the VSF index. The results shows that the AC voltage stability is guaranteed and enables the interconnection to an weak AC system, when compensation factor of the compensation capacitor is higher than 200%.

• Proceedings of the KIEE Conference
• /
• 2002.07c
• /
• pp.1685-1687
• /
• 2002

High voltage(H.V.) induction motors have been applied to various industrial applications. But aging and failure of induction motors are initiated by electrical, mechanical, thermal and chemical processes during manufacturing or in-service. These detects reduce locally the dielectric strength of the insulation. At such defects partial discharges can occur, which cause further degradation of the insulation and reduce the life time of the H.V induction motors. Consequently in this paper, we studied the partial discharge pattern analysis of H.V. induction motor for on-site applications.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.745-750
• /
• 2014

The chatter vibration in the machining process plays bad role in machining quality such as high roughness as well as tool life and machine failure. And the grinding process under this risk in the fully automated factory is exposed to the unexpected mass machining quality problem. Studying the vibration signal of the hub bearing grinding process, the reason of chatter vibration was explained with the specific machining pattern of chatter. And this study suggests the chatter detecting method in the production line, which is monitoring the peak acceleration level around the natural frequencies of the specimen, and calculating kurtosis value by assuming the chatter is related to the resonance of the specimen. The suggested method was applied to the vehicle hub bearing grinding process and proved good to detecting the chatter induced machining quality problem.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.11b
• /
• pp.235-239
• /
• 2000

For the calculation of internal stability, the hypothesis in conventional design is on the basis of two distinct zones, which are 'active zone' and 'passive zone'. This means that there is an abrupt discontinuous transition from active to passive states across a potential failure line. The existence of a discontinuity of this nature appears physically unreasonable, especially from kinematic considerations. A series of pull-out model tests was undertaken from a wall being rotated about the toe to find the strain distribution mobilized from near the wall face into the deep, stable zone through the centre plane. With this finding of transition zone, the objective of study is aiming at identifying the likely effect of this zone in designing method by comparing with the prevailing design method.