• Journal of the Korean Society of Safety
• /
• v.25 no.6
• /
• pp.128-136
• /
• 2010

In according with concrete structural design standard, it is common designing flexure reinforcement concrete to induce tension failure. So reinforcing ratio is limited to inducing tension failure. And maximum reinforcing ratio is regulated to protecting concrete compression strength caused by over reinforced building. Minimum reinforcing ratio is also limited in designing standard to protecting brittle failure as extremely using less reinforcing bar. But in minimum reinforcing ratio it is extremely conservative or it is sometimes impossible to induce stable tension-failure because they are depending on yield failure and experienced method and concrete designing standard strength. Therefore the purpose of the present paper is to evaluate the flexural behavior of minimum steel ratio of reinforced concrete of beams and to propose the guide-line of equation of minimum steel ratio by performing static flexural test of 16 beams according to size effect, number of steel, yielding stress of steel, and concrete compressive strength which are presumed effective variables. From experimental results, the equation of minimum steel ratio was newly proposed considered size effect.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05b
• /
• pp.691-698
• /
• 1996

This paper propose a procedure to estimate the system lifetime distribution using simulation method in a parametric framework and also develop the criterion for terminating the simulation. We assume that a system is composed of many components whose lifetime and repair time distributions are general, and repair of each component is imperfect or not. General simulation algorithms can not be adopted for this case, due to the dependency of successive operating times and the discontinuity in base line intensity function of failure process. Then we propose algorithms for generating failure times subject to imperfect repair. We develop the event time tracking logic for identifying the system failure time, and also develop the criterion for terminating the simulation. Our procedure is composed of two phases. The first phase of the procedure is to generate the system failure times from the inputs. The second phase is to estimate the lifetime distribution of the system. The best model is selected by a fully automated procedure among well-known parametric families, and the required parameters are estimated. We give examples to show the accuracy of our procedure and the effect of repair effect of components to system MTTF(Mean Time To Failure).

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.2110-2111
• /
• 2008

Continuous on-line temperature monitoring allows corrective measures to be taken to prevent upcoming failure. Continuous temperature monitoring and event recording provides information on the energized equipment's response to normal and emergency conditions. On-line temperature monitoring helps to coordinate equipment specifications and ratings, determine the real limits of the monitored equipment and optimize facility operations. Using wireless technique eliminates any need for special cables and wires with lower installation costs if compared to other types of online condition monitoring equipment. In addition, wireless temperature monitoring works well under difficult conditions in strategically important locations. Wireless technology for on-line condition monitoring of energized equipment is applicable both as standalone system and with an interface with power quality monitoring system.

• The KSFM Journal of Fluid Machinery
• /
• v.8 no.6 s.33
• /
• pp.7-14
• /
• 2005

The waterhammer occur when the pumps are started or stopped for the operation or tripped due to the power failure, and the hydraulic transients take place as a result of the sudden change in velocity. Several times, the field tests of the waterhammer were carried out for Pangyo booster pumping station. Pangyo pumping station was installed with the booster pumps of 6 sets and the in-line pumps of 2 sets. The in-line pumps are additionally needed to the surge suppression device so that the pumping station acquire the safety and reliability for the pressure surge.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.49 no.4
• /
• pp.143-151
• /
• 2000

Electric power distribution feeders are susceptible to faults caused by a variety of situations such as adverse weather conditions, tree contacts, equipment failure, accidents, etc. Distribution circuit faults result in a number of problems related to the reliability of service and customer power quality. In the distribution line, the permanent interruption of customer service resulting from a blown fuse or a recloser lockout was the only factor which was used to determine service reliability. On underground distribution line, the serving of cables by earth-moving equipment is a prevalent cause of faults and the most cable faults quickly develop into bolted current. we introduce th multi-circuit breaker coordination methods in the Underground Distribution Line.

• Proceedings of the KIEE Conference
• /
• 1995.07b
• /
• pp.616-619
• /
• 1995

This paper describes developement of on-line system for vibration signal analysis. In the power system, the main reason of transformer fault is due to a large amount of current by a short-circuit and a ground-fault. The electromagnetic force caused by fault-current deforms transformer windings and results in vibration pattern change. Therefore if the continuous on-line vibration monitoring on transformer is performed, an incipient failure can be detected. The developed system is composed of data acquisition devices, user interface program, signal processing program, diagnosis and trend analysis program, self diagnosis program and communication program.

• Proceedings of the KSR Conference
• /
• 2006.11b
• /
• pp.723-730
• /
• 2006

In the electrical railway, the tension ascension of contact wire is essential to speed up of train and current collection performance of catenary largely depends on the tension. The tension variation rate of the tensioning device used in existing line limits within 5%, and the tension variation rate of the spring-type tensioning device installed at the section where tensioning length is short bounds within 15%. So it is urgent for us to localize it for high speed line, which the tension variation rate is limited within 3%. Therefore in this study, a pulley-type tensioning device for high speed line is developed. To verify the performance of developed device, a performance test, overload test and failure test is carried out under the code of the Kyung-Bu High Speed line. And it is secured durability performance through a fatigue test.

• Proceedings of the KIEE Conference
• /
• 2004.11b
• /
• pp.187-189
• /
• 2004

This paper investigates the effect of weather factors(such as winds, rain, snows, temperature, clouds and humidity) on transmission line outages. The result shows that weather variables have significant effects on the transmission line historical outages and the relationship between them is nonlinear. Multiple regression analysis using Logit model is proved to be appropriate in forecasting line failure rate in KEPCO systems. It could also provide system operators with useful informations about system operation and planing.

• Wind and Structures
• /
• v.38 no.4
• /
• pp.325-339
• /
• 2024

The longitudinal force resulting from tornado loads on transmission line is considered a crucial factor contributing to the failure of transmission line structures during tornado events. Accurate estimation of this longitudinal force poses a challenge for structural designers. Therefore, the objective of this paper is to provide a set of charts that can be easily used to estimate the peak longitudinal forces transferred from the conductors to a tower. The critical wind field and corresponding configuration considered in this paper are previously studied and determined. The charts should account for all the conductor parameters that can affect the value of the longitudinal force. In order to achieve that, a parametric study is first conducted to assess the variation of the longitudinal forces with different conductor parameters, based on the critical tornado configuration. Results of this parametric study are used to develop the charts that can be used to calculate longitudinal forces by adopting a multi-variable line regression. The forces calculated from charts are validated by finite element analysis. An example for the usage of the charts is provided at the end of this paper.

• Journal of the Microelectronics and Packaging Society
• /
• v.23 no.2
• /
• pp.79-84
• /
• 2016

A flexible electronic device deformed by external force causes the failure of a semiconductor die. Even without failure, the repeated elastic deformation changes carrier mobility in the channel and increases resistivity in the interconnection, which causes malfunction of the integrated circuits. Therefore it is desirable that a semiconductor die be placed on a neutral line where the mechanical stress is zero. In the present study, we investigated the effects of design factors on the position of neutral line by finite element analysis (FEA), and expected the possible failure behavior in a flexible face-down packaging system assuming flip-chip bonding of a silicon die. The thickness and material of the flexible substrate and the thickness of a silicon die were considered as design factors. The thickness of a flexible substrate was the most important factor for controlling the position of the neutral line. A three-dimensional FEA result showed that the von Mises stress higher than yield stress would be applied to copper bumps between a silicon die and a flexible substrate. Finally, we suggested a designing strategy for reducing the stress of a silicon die and copper bumps of a flexible face-down packaging system.