• Journal of Applied Reliability
• /
• v.8 no.2
• /
• pp.101-111
• /
• 2008

Good diagnostics improves both the safety and system unavailability of digital safety systems. The measure of a diagnostic capability is called the Coverage Factor. Because the Failure Modes, Effects and Diagnostic Analysis (FMEDA) provides information on the failure rates and failure mode distributions necessary to calculate a diagnostic coverage factor for a component, the FMEDA can be used as a useful tool to calculate it. Through performing FMEDA on a digital signal processor (DSP) board used in a digital safety system, it is shown that some components of the DSP board can be replaced or improved to satisfy the required diagnostic coverage. That is, the FMEDA can serve as a useful verification tool to design a diagnostic capability for the DSP board.

• Journal of Sensor Science and Technology
• /
• v.22 no.3
• /
• pp.191-196
• /
• 2013

A particulate matter sensor fabricated by MEMS process is proposed. It is developed to accommodate Euro6 on-board diagnostics regulation for diesel automobile. In the regulation, emission of diesel particulate matter is restricted to 9 mg/km. Particulate matter sensor is designed to use induced charges by charged particulate matter. To increase sensitivity of the sensor, groove is formed on sensor surface because wider surface area generates more induced charges. Sensitivity of the sensor is measured 10.6 mV/(mg/km) and the sensor shows good linearity up to 15.7 mg/km. Also its minimum detectable range is about 0.25 mg/km. It is suitable to detect failure of a diesel particulate filter which should filter particulate matter more than 9 mg/km. For removing accumulated particulate matter on the sensor which can disturb normal operation, platinum heater is designed on the backside of the sensor. The developed sensor can sense very low amount of particulate matter from exhaust gas in real-time with good linearity.

• Korean Journal of Pharmacognosy
• /
• v.52 no.3
• /
• pp.127-133
• /
• 2021

Platelet activation plays a major role in cardiovascular disorders (CVDs). Thus, disrupting platelet activation represents an attractive therapeutic target on CVDs. Esculetin, a bioactive 6,7-dihydroxy derivative of coumarin, possesses pharmacological activities against obesity, diabetes, renal failure, and CVDs. In other report, the effect of esculetin has been examined in human platelet activation and experimental mouse models, and esculetin inhibited collagen- and arachidonic acid-induced platelet aggregation in washed human platelets. However, it had no effects on other agonists such as thrombin and U46619, and its mechanism is not also clearly known. This study investigated the effect of esculetin on collagen-induced human platelet aggregation, and we clarified the mechanism. Esuletin has effects on the down regulation of PI3K/Akt and MAPK, phosphoproteins that act in the signaling process in platelet aggregation. The effects of esculetin reduced of TXA₂ production and phospholipase A₂ activation, and intracellular granule secretion including ATP and serotonin, leading to inhibit platelet aggregation. These results clearly clarified the effect of esculetin in inhibiting platelet activity and thrombus formation in humans.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.6
• /
• pp.9-16
• /
• 2020

This study aims to assess the effects of specimen thickness (ST) on fatigue crack growth in the early stages of crack propagation and near failure in magnesium alloys. The analysis of variance (ANOVA) method was adopted because fatigue crack propagation in magnesium alloys exhibits statistical behavior. The equality of variance test and residual diagnostics were performed on the grown cracks to confirm the validity of ANOVA by verifying the normal distribution and mutual independence of the residuals and their homoscedasticity. ANOVA confirmed that ST heavily impacts crack growth; i.e., when ST is smaller, cracks grow faster in the early crack propagation stage and break more quickly before the formation of larger cracks. We found that ST significantly affects fatigue crack growth in the early crack propagation stage and near the failure stage in magnesium alloys. The regression model was also used to predict crack formation near the failure stage.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.525-526
• /
• 2007

Continuous on-line temperature monitoring provides the means to evaluate current condition of equipment and detect abnormality. It allows corrective measures to be taken to prevent upcoming failure. Continuous temperature monitoring and event recording provides information on the energized equipment's response to normal and emergency conditions. On-line temperature monitoring helps to coordinate equipment specifications and ratings, determine the real limits of the monitored equipment and optimize facility operations. Using wireless technique eliminates any need for special cables and wires with lower installation costs if compared to other types of online condition monitoring equipment. In addition, wireless temperature monitoring works well under difficult conditions in strategically important locations. Wireless technology for on-line condition monitoring of energized equipment is applicable both as standalone system and with an interface with power quality monitoring system.

• Smart Media Journal
• /
• v.1 no.1
• /
• pp.58-63
• /
• 2012

It is a superordinate concept to a network control system which optimally distributes the battery power to overall length parts through the linkage control drive and absorbs/integrates network diagnostics and overlapped functions with overall length control systems. This study is to develop a system that maximize the battery power and motor effectiveness by controlling motor battery controlling module with common MCU Integration linkage controlling system, and to develop S/W and H/W that can be controlled by linked with each controlling module in CAN method through using Autosar's standardized software.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.04c
• /
• pp.106-110
• /
• 2008

Continuous on-line temperature monitoring allows corrective measures to be taken to prevent upcoming failure. Continuous temperature monitoring and event recording provides information on the energized equipment's response to normal and emergency conditions. On-line temperature monitoring helps to coordinate equipment specifications and ratings, determine the real limits of the monitored equipment and optimize facility operations. Using wireless technique eliminates any need for special cables and wires with lower installation costs if compared to other types of online condition monitoring equipment. In addition, wireless temperature monitoring works well under difficult conditions in strategically important locations. Wireless technology for on-line condition monitoring of energized equipment is applicable both as standalone system and with an interface with power quality monitoring system.

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10a
• /
• pp.61-66
• /
• 1992

In this paper, a method for implementing software for the control system with dual structure in processor module is proposed and implemented to enhance its reliability. In this implementation the multi-tasking function which is provided by a real-time operating system is applied. The overall softwre is divided into five tasks and is performed in each of the dual processor module, independently. By this, the processor module with dual structure can achieve a control objective and fault diagnostics effectively. An experimental result shows that the backup processor module can be substituted for the primary processor module immediately when it happens to fail, because data relating the failure information are exchanged continuously done via shared memories.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.2110-2111
• /
• 2008

Continuous on-line temperature monitoring allows corrective measures to be taken to prevent upcoming failure. Continuous temperature monitoring and event recording provides information on the energized equipment's response to normal and emergency conditions. On-line temperature monitoring helps to coordinate equipment specifications and ratings, determine the real limits of the monitored equipment and optimize facility operations. Using wireless technique eliminates any need for special cables and wires with lower installation costs if compared to other types of online condition monitoring equipment. In addition, wireless temperature monitoring works well under difficult conditions in strategically important locations. Wireless technology for on-line condition monitoring of energized equipment is applicable both as standalone system and with an interface with power quality monitoring system.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.403-405
• /
• 1999

Power transformers have a tendency of ultra-high voltage and huge capacity as power demand increases day after day. Therefore, the fault by insulation destruction gives rise to large area of power failure in huge capacity transformers. On-line predictive diagnostics is very important In power transformers because of economic loss and its spreading effect. Hence, this study presents experiments of partial discharge method using ultrasonic sensor in order to confirm the possibility of ultrasonic sensor in power transformers. It carries out the experiments of measuring delay time between ultrasonic sensor and transducer, sensitiities by temperature change of oil and by barriers inside transformers. It is also Included wave analysis by ultrasonic sensor for needle-plate electrode powered on through high-voltage equipments.