• Journal of the Korean Geotechnical Society
• /
• v.27 no.10
• /
• pp.25-33
• /
• 2011

Suction buckets have been widely used for offshore structures such as anchors for floating facilities, and the foundations of offshore wind energy turbines. However, the design guidelines for suction buckets have not been clearly suggested. Therefore, this study performed the numerical analysis by using ABAQUS (2010) to evaluate bearing capacities and load-movement behaviors of the suction bucket in NC clay. For the numerical analysis, the depth ratio L/D (L=embedded length of skirt; D=diameter of a bucket) was varied from 0.25 to 1.0. The analysis results showed that the L/D ratio has a significant effect on the bearing capacity, and the vertical and horizontal capacities respectively increased by about 40% and 90%, when L/D ratio increased from 0.25 to 1.0. At the vertical loading, the bucket showed the similar failure mode with a deep foundation, so the shaft and toe resistances can be separately evaluated. At the horizontal loading, the bucket with L/D=O.25 showed the sliding failure mode and the bucket with $L/D{\geq}0.5$ showed the rotational failure mode.

• International Journal of Highway Engineering
• /
• v.17 no.2
• /
• pp.55-62
• /
• 2015

Cracking is an inevitable fact of asphalt concrete pavements and plays a major role in pavement deterioration. Pavement cracking is one of the main factors determining the frequency and method of repair. Cracks can be treated with a number of preventative maintenance actions, including overlay surface treatments such as slurry sealing, crack sealing, or crack filling. Pavement cracks can show up as one or all of the following types: transverse, longitudinal, fatigue, block, reflective, edge, and slippage. Crack sealing is a frequently used pavement maintenance treatment because it significantly extends the pavement service life. However, crack sealant often fails prematurely due to a loss of adhesion. Because current test methods are mostly empirical and only provide a qualitative measure of the bond strength, they cannot accurately predict the adhesive failure of the sealant. This study introduces a laboratory test aimed at assessing the bonding of hot-poured crack sealant to the walls of pavement cracks. A pneumatic adhesion tensile testing instrument (PATTI) was adopted to measure the bonding strength of the hot-poured crack sealant as a function of the curing time and temperature. Based on a limited number of test results, the hot-poured crack sealants have very different bonding performances. Therefore, this test method can be proposed as part of a newly developed performance-based standard specification for hot-poured crack sealants for use in the future. PURPOSES : The purpose of this study was to evaluate both the adhesion and failure performance of a crack sealant as a function of its curing time and curing temperature. METHODS: A pneumatic adhesion tensile testing instrument (PATTI) was adopted to measure the adhesion performance of a crack sealant as a function of the curing time and curing temperature. RESULTS: With changes in the curing time, curing temperature, and sealant type, the bond strengths were found to be significantly different. Also, higher bond strengths were measured at lower temperatures. Different sealant types produced completely different bond strengths and failure behaviors. CONCLUSIONS: The bonding strength of an evaluated crack sealant was shown to differ depending on various factors. Two sealant types, which were composed of different raw materials, were shown to perform differently. The newly proposed test offers the possibility of evaluating and differentiating between different crack sealants. Based on alimited number of test results, this test method can be proposed as part of a newly developed performance-based standard specification for crack sealants or as part of a guideline for the selection of hot-poured crack sealant in the future.

• Journal of the Korea Concrete Institute
• /
• v.28 no.4
• /
• pp.473-480
• /
• 2016

The purpose of this study is to provide analytical method to reasonably evaluate the complicated failure behaviors of shear friction of reinforced concrete shear wall specimens using grade 500 MPa high-strength bars. A total of 16 test specimens with a variety of variables such as aspect ratio, friction coefficient of interface in construction joint, reinforcement details, reinforcement ratio in each direction, material properties were selected and the analysis was performed by using a non-linear finite element analysis program (RCAHEST) applying the modified shear friction constitutive equation in interface based on the concrete design code (KCI, 2012) and CEB-FIP Model code 2010. The mean and coefficient of variation for maximum load from the experiment and analysis results was predicted 1.04 and 17% respectively and properly evaluated failure mode and overall behavior characteristic until failure occur. Based on the results, the analysis program that was applied modified shear friction constitutive equation is judged as having a relatively high reliability for the analysis results.

• Korean Journal of Materials Research
• /
• v.11 no.1
• /
• pp.8-14
• /
• 2001

Microstructural evolution and creep failure behavior of GTD 111 have been studied. Solidification and precipitation behaviors of the alloy during casting have been analyzed by microstructural observations. It has been found that MC carbides solidify just before the $\gamma$/$\gamma$' eutectic solidification. The ηphase was found to be formed by transformation of Ti-rich $\gamma$'phase. PFZ has formed in the vicinity of the transformed $\eta$ phase. A few MC particles, which have been identified as TaC, precipitated within the PFZ. Creep failure along grainboundary was dominant at and above $871^{\circ}C$. Creep failure above$ 871^{\circ}C$ was caused by the propagation of surface cracks and internal cracks. Creep crack has initiated at the microporosities embedded on the grainboundary. The $\eta$phase and PFZ have been found to be little or no effect on creep crack initiation.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.20 no.5
• /
• pp.381-389
• /
• 2000

Metal matrix composite(MMCs) have been rapidly becoming one of the strongest candidates for structural materials for high temperature application. It is well recognized that MMCs always experience at least one large cool-down from processing temperature before my significant applied service loading. Due to the large difference in thermal expansion coefficient between the fiber and matrix, large thermal residual stresses generally develop in composites. It was reported from many previous studies that the effects of thermal residual stress on mechanical properties and fracture behavior were much more complex and dramatic than conventional engineering materials. Therefore it is crucial to evaluate the effect of heat treatment which changes the characteristic of distribution of thermal residual stress in MMCs. Single fiber composite(SFC) test based on the balance in a micromechanical model is a quite convenient method to evaluate interfacial shear strength(IFSS) and the failure mode of composite. In this study the effect of heat treatment on IFSS and the microscopic failure mechanism of MMC is investigated by combining acoustic emission(AE) technique with SFC test. The characteristic of AE signal, IFSS and microscopic failure mechanism due to heat treatment condition is discussed.

• Journal of the Korea Concrete Institute
• /
• v.20 no.4
• /
• pp.503-511
• /
• 2008

This paper presents the results of an analytical and experimental study on the performance of reinforced concrete beams subjected to pure torsion. The main parameters of the experimental tests were amount of torsional reinforcement and the ratio of the transverse torsional reinforcement to the longitudinal torsional reinforcement. The test results indicated that the maximum amount of torsional reinforcement required in ACI 318-05 code underestimated almost twice as much as the observed maximum amount of torsional reinforcement. Comparisons between the tested and calculated torsional behaviors of the 102 beams showed that the torsional failure modes of ACI 318-05 code disagreed with the observed failure modes. In addition, the torsion provisions in ACI 318-05 code overestimate the torsional strength of the RC beams in which relatively large amount of torsional reinforcement were reinforced, while underestimate for the beams with small amount of torsional reinforcement. This discrepancy between the theoretical ultimate torsional strength as given by the ACI 318-05 code and the experimental one can be due to neglecting the tension stiffening effect and the contribution of the torsional strength by concrete.

• The Journal of Engineering Geology
• /
• v.14 no.1
• /
• pp.71-80
• /
• 2004

The failure of cut slopes frequently occurs particularly during the thawing season and the rain season in summer. This study interpreted data collected from site to which a real-monitoring system was applied in order to analyze the causes of ground behaviors and to forecast future slope failure. As for research methods, this study analyzed the size and mechanism of failure by integrating the results of field surveys and measurements. Furthermore, it analyzed data transmitted by the monitoring system installed in the a result, three times of ground displacement occurred as well as a number of partial tension cracks. The cut slope composed of sandstone and siltstone started its initial behavior as a result of torrential downpour and the loss of support of the substructure. For quantitative analysis of the characteristics of ground behavior, this study measured 5 lateral lines. According to the result of the measurement, displacement happened little in the section to which countermeasure had been applied, but displacement of maximum 400mm happened in the section to which countermeasure had not bee applied. The analysis of data on displacement and rainfall suggested a close relationship between ground behavior and rainfall. According to the result of stability interpretation along with the change of ground saturation, stability rate appeared to be less than 1.0 when ground saturation is over 55%. Although the current trend of ground behavior is at a stable stage falling within the range of tolerance, it is considered necessary to continue monitoring and data analysis because ground displacement is highly possible with the change of temperature during the winter.

• Journal of the Korean Geotechnical Society
• /
• v.25 no.4
• /
• pp.91-103
• /
• 2009

Slope failure depends upon the climatic features related to related rainfall, structural geology and geomorphological features as well as the variation of the mechanical behaviors of soil constituting a slope. In this paper, among many variables, effects of soil layer thickness on the slope failure process, and variations of matric suction and volumetric water content were observed. When the soil layer is relatively thick, the descending wetting front decreases matric suction and the observed matric suction reaches to "0" value. When the wetting front reaches to the impermeable boundary, the bottom surface of steel soil box, ascending wetting front was observed. This observation can be postulated to be the effects of various sizes of pores. When macro size pores exist, the capillary effects can be reduced and infilling of pore will be limited. The partially filled pores would be filled with water during the ascending of the wetting front, which bounces from the impermeable boundary. This assumption has been assured from the observation of variation of the volumetric water contents at different depth. When the soil layer is thick (thickness = 20 cm), for granular material, erosion is a cause triggering the slope failure. It has been found that the initiation of erosion occurs when the top soil is fully saturated. Meanwhile, when the soil layer is shallow (thickness = 10 cm), slope slides as en mass. The slope failure for this condition occurs when the wetting front reaches to the interface between the soil layer and steel soil box. As the wetting front approaches to the bottom of soil layer, reduction of shear resistance along the boundary and increase of the unit weight due to the infiltration occur and these produce complex effects on the slope failure processes.

• Asia Marketing Journal
• /
• v.14 no.1
• /
• pp.99-130
• /
• 2012

Service failure and a poor service recovery may lead loyal customers to try to aggressively punish the service firm. We use perceived betrayal and desire for vengeance as the key constructs to understand customer retaliation. Perceived betrayal is defined as a customer's belief that a firm has intentionally violated what is normative in the context of their relationship. And the desire for vengeance is defined as the retaliatory feelings that consumers feel toward a firm, such as the desire to exert harm on the firm. The perceived betrayal and the desire for vengeance are key antecedents of retaliatory behaviors such as vindictive complaining, negative WOM and third-party complaining for publicity. The empirical results suggest that betrayal is a key motivational factor that lead customers to restore fairness by making use of all means, including retaliation. We also find that relationship quality has effect on a customer's response to a failure in service recovery. As the levels of relationship increases, a violation of the proper fairness has a stronger effect on the sense of betrayal experienced by customers. Considerable research has investigated consumer responses to dissatisfaction. But our study examine the response of outraged and highly frustrated consumers. We focus on emotional and behavioral processes that have not been covered by previous dissatisfaction researches and which are unique to outraged consumers caused by extremely dissatisfied purchase experience. It has recently been pointed out by various mass media that the customers not only have positive effects on the company performance but also put the company in crisis. It has often been reported that one customer's dissatisfaction, for example, never ends as it is, and it tends to grow for retaliating upon the company, depending on the level of seriousness of the dissatisfaction. This sometimes leads to a lawsuit against the company. Our study focuses on the customers' emotional and behavioral responses induced by their extreme dissatisfactions. We divided the customer groups into the customers with high relationship quality and the customers with low relationship quality, and the difference between two groups is examined. The objective of this study is to comprehend the causal relationship between the feeling of betrayal caused by the service failure and the retaliatory behavior triggered by the desire of revenge. Our study is divided into three parts. First, a causal relationship between perceived unfairness and the perceived betrayal and desire for revenge. Second, the effect of the perceived betrayal and desire for revenge on the retaliatory behavior is investigated. Finally, the moderating role of relationship quality in the causal relationship between the unfairness in service recovery and the perceived betrayal is analyzed. This study finds the following empirical results. The distributive unfairness, procedural unfairness and interactional unfairness had significant effects on the perceived betrayal. Especially, the perceived distributive unfairness results in the highest perceived betrayal. When the service company does not provide customers proper and sufficient compensation for the failure, they feel the strong sense of betrayal. And in the causal relationship between the perceived betrayal, desire for revenge and retaliatory behavior, the perceived betrayal has significant effects on e desire for revenge. In addition desire for revenge has significant effects on negative word of mouth, retaliatory complaining behavior and publicity of complaints through third group. Therefore the perceived unfairness has effects on retaliatory behavior through the mediation of the perceived betrayal and desire for revenge. Finally the moderating role of relationship quality was examined in the relationship between the unfairness and perceived betrayal. If the customers experienced the perceived unfairness in the process of service recovery, the customers with high relationship quality feel the stronger perceived betrayal than the customers with low relationship quality do. When they experience the double service failure, the customer group with high relationship quality accumulating the sense of trust feel the more perceived betrayal than the customer with low relationship quality who do not have strong trust. The contribution of this study is to find the effect of the service failure on the retaliatory behavior with the moderating roles of relationship quality. The dimensions of unfairness in service recovery is found to have differential effects on the perceived betrayal, desire for revenge. And these differential effect is moderated by the level of relationship quality.

• Journal of the Korean GEO-environmental Society
• /
• v.16 no.3
• /
• pp.41-48
• /
• 2015

Several sensor systems are used to estimate and predict the slope behaviors, however though slope sensing systems are much up-to-dated compared to before, they are mainly focused on the hardware developing. It means the analyzing software is deficient to apply the examining slope behavior for slope stability. In real case, slope behavior shows the 3-dimensional movement and failure; however the modeling methods for 3-D behavior are more difficult and need more variables. 1-D analysis shows only the length variation, however the real slope makes the 3-D behaviors. To fix the 3-D space coordinate, three values should be determined such as length, horizontal angle and vertical angle. Therefore if the 3-D coordinate system were composed by the points considered of two directions and length, the 3-D space could be separated into horizontal plane and vertical plane. The data from DY-slope in Chungbuk province was analyzed to the developed 3-D coordinate system. It is concluded from the results of 3-D analysis, the slope is generally moving to transverse direction, also the displacements are happening to road and vertical direction at the same time. Presently, the accumulated displacement between sensing points shows small value within 4.3 cm, and the displacements of all sensing points show the similar directions and magnitudes.