• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.16 no.5
• /
• pp.1-11
• /
• 2017

Expressway network which plays an important role on land transportation system, have been developing quantitatively and qualitatively with $7{\times}9$ structure. To cope with complex geometric condition, guidance lane marking has been installed to induce safer lane-changing maneuver. However, there is no standard on guidance lane marking and its effectiveness is also verified with limited scope. The major purpose of this research is to clarify its effectiveness in terms of driving safety aspect using virtual driving simulator and to suggest standard on the proper length. To carry this out, preference data from subjects was collected and lane-changing pattern within virtual driving environment was investigated. In addition, in order to quantify the level of comfort, Electroencephalogram data was collected and validated using statistical test. Finally, it is expected that this research can be used to establish standard on guidance lane marking.

• Journal of the Korean Geotechnical Society
• /
• v.29 no.12
• /
• pp.105-111
• /
• 2013

The standard penetration test (SPT) has been widely used because of its usability, economy, and many correlations with soil properties among other factors. In SPT, hammer energy is an important factor to evaluate and calibrate N values. To measure hammer energy, an instrumented SPT rod was developed considering that stress waves transferring on rods during SPT driving are the same as stress waves transferring on piles due to pile driving. Using this idea, an instrumented SPT rod with a pile driving analyzer was applied as a pile capacity prediction tool in this study. In order to evaluate this method, SPT and dynamic cone tests with the instrumented SPT rod were conducted and also 2 pile load tests were performed on pre-bored steel pipe piles at the same test site. End bearings were predicted by CAPWAP analysis on force and velocity waves from dynamic cone penetration tests and SPT. Comparing these predicted end bearings with static pile load tests, a new prediction method of the end bearing capacity using the instrumented SPT rod was proposed.

• International Journal of Highway Engineering
• /
• v.19 no.5
• /
• pp.163-171
• /
• 2017

PURPOSES : Traffic safety facilities are used to prevent traffic accidents before they occur by providing drivers with information on traffic situations and the geometric design of roads. However, some facilities not defined in guidelines do not meet installation criteria, yet are being installed and used in order to increase efficiency in traffic flow and prevent traffic accidents in a specific expressway zone. In this study, we have evaluated the effect of delineation system which are not defined in the guideline criteria. METHODS : Different virtual scenarios were created for roads using expressway median barrier chevron signs, with a driving simulator used to evaluate the installation and operational effect of such signs. Ten experiments were performed with left- and right-curved roads at curve radius intervals of 500 m, from 500 m to 2,500 m. RESULTS : For sections with a curve radius of more than 1,500 m, drivers had a clear tendency toward stable driving regardless of delineation system. When a chevron sign is installed on a protection fence in the road curving left, an expanded installation is recommended up to the section with a curve radius of 1,000 m. According to the analysis results for the RHB (Relative High Beta spectrum), driving concentration also improved up to a curve radius of 1,000 m. CONCLUSIONS :The experiment result indicates the extent of biasing within a lane and the manipulation amount of steering handle, were analyzed and found to be affected by curve radius and road alignment regardless of delineation system.

• Journal of Korean Society of Transportation
• /
• v.33 no.1
• /
• pp.81-89
• /
• 2015

Crashes that occur at tollgates have different characteristics compared to those of the mainline on expressways in terms of crash cause, crash type, and vehicle type. Due to this fact, the safety performance function (SPF) focused on the expressway tollgates, apart from the mainline, should be developed. The aim of this study is, therefore, to identify the influential factors and develope a SPF for crashes at tollgates. Firstly, we established independent variables affecting crashes at tollgates through literature review and descriptive statistical analysis. Based on these variables, two negative binomial regression models with different form of independent variables were developed and goodness-of-fits of each model were compared. According to the results, the number of crashes increases i) as AADT, Hi-pass rate, and heavy vehicle rate increase, ii) as average lane width decreases, iii) on the mainline tollgate type. The safety performance function developed in this study could be applied to select hot-spots for expressway tollgates.

• Journal of the Korea Concrete Institute
• /
• v.27 no.6
• /
• pp.695-703
• /
• 2015

Acceptance criteria for chemical admixtures of cement concrete were investigated in domestic and international specifications. The reliability was verified for solid content test method of chemical admixture examined statistical analysis by round robin test. The applicability of FT-IR spectroscopy for qualitative measurement of multi-compound chemical admixtures verified. From solid content experimental results, outlier analysed using Cochran, Grubbs and Dickson's Q test. Repeatability and reproducibility standard deviation for solid content results showed 0.25 and 0.098% respectively according to KS A ISO 5725-2 procedure, it can be confirmed reliability of test methods. FT-IR spectrum of liquefied or oven-dried chemical admixtures condition showed big differences. It is needed that the FT-IR analysis is performed on dry material. However there's no difference with the applicability of FT-IR spectroscopy for multi-compound chemical admixtures. So the utility of method analysis could not identify.

• International Journal of Highway Engineering
• /
• v.14 no.3
• /
• pp.121-130
• /
• 2012

This study develops the evaluation model which is for assessing on the side of users in expressway service areas. The direction of development on Evaluation Criteria is all about on the side of necessity of service area users, the reflection of current conditions, the construction of total evaluation criteria, and the examination of connecting study with current study. After that, this study examines previous evaluation criterias and researchers will select the primary provision of evaluation through FGI, and they derive the final evaluation criteria throughout the verification of suitability on Evaluation Criteria. Throughout AHP analysis which is a professional survey system of users, researchers derive on the side of facilities, on the side of operations, on the side of environments, and on the side of services in order by the weightings.

• Journal of Korean Society of Transportation
• /
• v.27 no.6
• /
• pp.129-137
• /
• 2009

Operation of intelligent transport systems technologies in transportation networks and more detailed analysis give rise to necessity of dynamic traffic analysis model. Existing static models describe network state in average. on the contrary, dynamic traffic analysis model can describe the time-dependent network state. In this study, a dynamic traffic model for the expressway system using FTMS data is developed. Time-dependent origin-destination trip tables for nationwide expressway network are constructed using TCS data. Computation complexity is critical issue in modeling nationwide network for dynamic simulation. A subarea analysis model is developed which converts the nationwide O-D trip tables into subarea O-D trip tables. The applicability of the proposed model is tested under various scenario. This study can be viewed as a starting point of developing deployable dynamic traffic analysis model. The proposed model needs to be expanded to include arterial as well without critical computation burden.

• Journal of Korean Society of Transportation
• /
• v.29 no.1
• /
• pp.113-123
• /
• 2011

The application of micro-simulation model has been extended farther with improvement of computer performance and development of complicated model. To make a micro-simulation model accurately replicate field traffic conditions, model calibration is very crucial. Studies on calibration of micro-simulation model have not been enough while lots of studies on calibration of macro-simulation model have been continued in our country. This paper presents an auto-calibration of parameter values in micro-simulation model(VISSIM) using genetic algorithm. RMSE(Root Mean Square Error) of collected volume on the urban expressway versus simulated volume is set as MOP(measure of performance) and objective function of optimization is set as to minimize the RMSE. Applying to urban expressway(Nae-bu circular) as a case study, it shows that RMSE of optimized parameter values decrease 60.4%($19.3{\longrightarrow}7.6$) compared to default parameter values and the proposed auto-calibration system is very effective.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.16 no.3
• /
• pp.50-58
• /
• 2017

TPCLT(Twice Per Cycle Left-turn) operation reduces this left-turn 'spill-over' problem on an as needed basis by servicing the protected left-turn movement as a leading and a lagging left-turn. In this study, to evaluate the effectiveness of TPCLT applied to three-legged signalized intersection in Korea, the analysis was carried out using VISSIM and SSAM model analysis. The study was implemented by three cases which are TPCLT operation, non-TPCLT operation and half-cycle operation using VISSIM program. According to the 9-left-turn volume scenario, total delay and travel times of each case was analyzed by VISSIM program. The study result shows more effective applying TPCLT operaion in the present ~ +50% scenario area at the intersection in terms of total delay.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.24 no.4
• /
• pp.157-167
• /
• 2020

In this study, a field bridge test was conducted to find the dynamic properties of cable supported bridges with resilient-friction base isolation systems (R-FBI). Various ambient vibration tests were performed to estimate dynamic properties of a test bridge using trucks in a non-transportation state before opening of the bridge and by ordinary traffic loadings about one year later after opening of the bridge. The dynamic properties found from the results of the tests were compared with an analysis model. From the result of the ambient vibration tests of the cable supported bridge with R-FBI, it was confirmed that the dynamic properties were sensitive to the stiffness of the R-FBI in the bridge, and the seismic analysis model of the test bridge using the effective stiffness of the R-FBI was insufficient for reflecting the dynamic behavior of the bridge. In the case of cable supported bridges, the seismic design must follow the "Korean Highway Bridge Design Code (Limit State Design) for Cable supported bridges." Therefore, in order to reflect the actual behavior characteristics of the R-FBI installed on cable-supported bridges, an improved seismic design procedure should be proposed.