• Proceedings of the Korean Geotechical Society Conference
• /
• 한국지반공학회 2006년도 추계 학술발표회
• /
• pp.312-333
• /
• 2006

This paper presents the results of an analysis of the excess porewater pressure distribution due to piezocone penetration in overconsolidated clays. From piezocone test results for moderately and heavily overconsolidated clays, it was observed that the excess porewater pressure increases monotonically from the piezocone surface to the outer boundary of the shear zone and then decreases logarithmically to the outer boundary of the plastic zone. It was also found that the size of the shear zone decreases from approximately 2.2 to 1.5 times the cone radius with increasing OCR, while the plastic radius is about 11 times the piezocone radius, regardless of the OCR. The equation developed in this study based on the modified Cam clay model and the cylindrical cavity expansion theory, which take into consideration the effects of the strain rate and stress anisotropy, provide a good prediction of the initial porewater pressure at the piezocone location. The method of predicting the spatial distribution of excess porewater pressure proposed in this study is based on a linearly increasing ${\Delta}u_{shear}$. In the shear zone and a logarithmically decreasing ${\Delta}u_{oct}$, and is verified by comparing with the excess porewater pressure measured in overconsolidated specimens at the calibration chamber.

• Journal of computational fluids engineering
• /
• 제21권4호
• /
• pp.96-101
• /
• 2016

A two-dimensional Stokes flow past a circular disk in a circular tube is analyzed. The circular disk is located coaxially with the circular tube and the Hagen-Poiseuille flow exists at upstream and downstream far from the circular disk. The Stokes approximation is used and the flow is investigated analytically by using the method of eigenfunction expansion and the method of least square. From the analysis, the stream function and the pressure of the flow field are obtained, and the streamlines and pressure distribution are shown. Also, the pressure and shear stress distributions on the circular disk and circular tube wall are calculated, and shown for some typical radii of the circular disk. The additional pressure drop induced by the disk and the drag force exerted on the disk are compared as functions of the radius of the circular disk, and it is shown that the shear force on the wall of the tube increases due to the disk.

• Steel and Composite Structures
• /
• 제22권2호
• /
• pp.399-409
• /
• 2016

The fracture propagation mechanism and fractured rock mass failure mechanism were important research in geotechnical engineering field. Many failures and instability in geotechnical engineering were related on fractures propagation, coalescence and interaction in rock mass under the external force. Most of the current research were limited to two-dimensional for the brittleness and transparency of three-dimensional fracture materials couldn't meet the requirements of the experiment. New materials with good transparent and brittleness were developed by authors. The making method of multi fracture specimens were established and made molds that could be reused. The tension-compression ratio of the material reached above 1/6 in normal temperature. Uniaxial and biaxial loading tests of single and double fracture specimens were carried out. Four new fractures were not found in the experiment of two-dimensional fractures such as the fin shaped crack, wrapping wing crack and petal crack and anti-wing crack. The relationship between stress and strain of the specimens were studied. The specimens with the load had experienced four stages of deformation and the process of the fracture propagation was clearly seen in each stage. The expansion characteristics of the fractured specimens were more obvious than the previous research.

• Steel and Composite Structures
• /
• 제15권5호
• /
• pp.481-505
• /
• 2013

This paper focuses on thermal post-buckling analysis of functionally graded beams with temperature dependent physical properties by using the total Lagrangian Timoshenko beam element approximation. Material properties of the beam change in the thickness direction according to a power-law function. The beam is clamped at both ends. In the case of beams with immovable ends, temperature rise causes compressible forces and therefore buckling and post-buckling phenomena occurs. It is known that post-buckling problems are geometrically nonlinear problems. Also, the material properties (Young's modulus, coefficient of thermal expansion, yield stress) are temperature dependent: That is the coefficients of the governing equations are not constant in this study. This situation suggests the physical nonlinearity of the problem. Hence, the considered problem is both geometrically and physically nonlinear. The considered highly non-linear problem is solved considering full geometric non-linearity by using incremental displacement-based finite element method in conjunction with Newton-Raphson iteration method. In this study, the differences between temperature dependent and independent physical properties are investigated for functionally graded beams in detail in post-buckling case. With the effects of material gradient property and thermal load, the relationships between deflections, critical buckling temperature and maximum stresses of the beams are illustrated in detail in post-buckling case.

• Journal of the Korean Society for Precision Engineering
• /
• 제18권9호
• /
• pp.89-95
• /
• 2001

Ceramic tool has to equip with not only high toughness and strength but also low thermal expansion and good thermal conductivity which leads to the high thermal shock resistance. These characteristics make it have longer tool life under thermal stress condition. In this study, commercial Si$_3$N$_4$ceramic cutting tool and home-made SiC based ceramic cutting tools which have different sintering time and chemical composition are tested under various cutting speed and the feed rate increase, the cutting force and the flank wear growth ratio increase, too. The performance of home-made SiC based ceramic cutting tool shows the possibility to be a new ceramic tool.

• Proceedings of the Korea Concrete Institute Conference
• /
• 한국콘크리트학회 2008년도 추계 학술발표회 제20권2호
• /
• pp.201-204
• /
• 2008

The proposed method, capable of predicting various stress-strain responses in axially loaded concrete confined with FRP (Fiber Reinforced Polymers) composites in a rational manner, is based on the fact that the volumetric expansion due to progressive microcracking in mechanically loaded concrete is an important measure of the extent of damage in the material microstructure. The elastic modulus expressed as a function of area strain and concrete porosity, the energy-balance equation relating the dilating concrete to the confining device interactively, the varying confining pressure, and an incremental calculation algorithm are included in the solution procedure. This procedure enables the evaluation of lateral strains consecutively according to the related mechanical model and the energy-balance equation, rather than using an empirically derived equation for Poisson's ratio or dilation rate as in other analytical methods.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 한국소음진동공학회 2008년도 춘계학술대회논문집
• /
• pp.132-139
• /
• 2008

The blade vibration problem of bladed disk is the most critical subject to consider since it directly affects the stable performance of the engine as well as life of the engine. Especially, due to complicated vibration pattern of the bladed disk, more effort was required for vibration analysis and test. The research of measuring the vibration of the bladed disk, using NSMS(Non-intrusive stress measurement) instead of Aeromechanics testing method requiring slip ring or telemetry system with strain gauge, was successful. These testing can report the actual stresses seen on the blades; detect synchronous resonances that are the source of high cycle fatigue (HCF) in blades; measure individual blade mis-tuning and coupled resonances in bladed disks. In order to minimize the error being created due to heat expansion, the tip timing sensor is installed parallel to the blade trailing edge, yielding optimal result. Also, when working on finite element analysis, the whole bladed disk has gone through three-dimensional analysis, evaluating the family mode. The result of the analysis matched well with the test result.

• Journal of the Korean Ceramic Society
• /
• 제18권2호
• /
• pp.99-104
• /
• 1981

Glass-ceramics possessed a number of characteristics which suggested their suggested their use for sealing to metals. The choice of particular glass-ceramics compositions for this application is governed by various factors, including workability of the glasses, thermal expansion characteristics and the matching of these to appropriate metals. Other properties, such as mechanical strength, determined the performance of glass-ceramics to metal seals. The purpose of the present study was to investigate direct sealing behaviour of copper to $Li_2O-ZnO-SiO_2$ system glass-ceramics. The design of the seal was a concentric seal which might contribute to the strong bond formation by providing compressive stress during thermal excursions. Tensile strengths of sealing layers were measured by Instron test machine. The layers were examined by electron probe microanalyzer. Crsystallization rate was increased with the amount of ZnO or $Li_2O$, and ZnO increased the sealing strength, but $Li_2O$ lowered it. Sealing mechanism was due to the formation of metal oxides, which acted as binder between copper and glass-ceramics. The nickle-plated copper seal with 10% $Li_2O$ and 30% ZnO was the most strong seal, and its sealing strength was more than 56kg/$\textrm{cm}^2$.

• Journal of the Korean Institute of Gas
• /
• 제9권1호
• /
• pp.26-32
• /
• 2005

This paper presents the design safety of metal seals in pressure vessels. For a high-pressure vessel, a metal seal is usually used as a primary sealing, and an elastomeric rubber O-ring is adopted as a secondary sealing unit. The FEM computed results show that an aluminium material for sealing a gas leakage is superior to a steel one because of the thermal expansion rate. The deformation and stress distributions on the metal seal and pressure vessel structures are mainly dominated by transferred temperature compared to those of the gas pressure in which is supplied by an external pump. Thus, the temperature of a metal seal material should be restricted to under $200^{\circ}C$.

• Journal of the Korean Institute of Gas
• /
• 제6권4호
• /
• pp.17-22
• /
• 2002

LNG demand has been rapidly increasing in Korea for a variety of reasons including stable supply, non-polluting, and high combustion efficiency characteristics. One of the most important structural core element of the LNG storage tank is the membrane, consisting of stainless steel. The membrane to be applied inside of LNG storage tank is provided with corrugations to absorb thermal contraction and expansion caused by LNG temperature. Experimental studies are presented to investigate the deformation and strength of the membrane which is designed by Kogas. All experiments are conducted on the basis of RPIS, and we found the results is fully satisfied with the RPIS.