• 한국연소학회:학술대회논문집
• /
• 2012.04a
• /
• pp.267-268
• /
• 2012

Soot formation and oxidation characteristics of air-diluted propane diffusion flames have been experimentally investigated under the elevated pressure conditions. PAH concentrations showed more pressure sensitive behavior comparing to soot volume fractions. The flame/soot temperatures in soot oxidation region were obtained using the MOLLIP technique. Under the complete soot oxidation environment, the flame/soot temperature is increased with pressure. The increased temperature could accelerate the soot oxidation process and then exothermic oxidation reaction, in turn, could further raise the flame/soot temperature, which would result in the enhancement of soot oxidation process.

• Applied Microscopy
• /
• v.27 no.4
• /
• pp.473-481
• /
• 1997

Disorder-order transformation of nanocrystalline FeAl have been investigated by a combination of electron and X-ray diffraction analysis including high resolution electron microscopy and differential scanning calorimetry. Fe-50at.%Al powders mechanically alloyed for 90 hours consist of $5\sim10$ nm size grains haying either disordered b.c.c. structure or amorphous structure. X-ray and electron diffraction of mechanically alloyed FeAl powders show that disorder-order transformation occurs at the temperature range of $300^{\circ}C\sim320^{\circ}C$. Such a low-temperature ordering behavior exhibiting an exothermic reaction is attributable to the nm-scale grain structure with a large amount of defects accumulated during mechanical alloying process.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.1
• /
• pp.145-148
• /
• 2011

The thermal behavior of lithiated Si anodes has been investigated using differential scanning calorimetry (DSC). In particular, the effect of Si particle size on the thermal stability of a fully lithiated Si electrode was investigated. For DSC measurements, a lithiated Si anode was heated in a hermetically sealed high-pressure pan with a polyvinylidene fluoride (PVDF) binder and a 1 M $LiPF_6$ solution in an ethylene carbonate (EC)-diethyl carbonate (DEC) mixture. The thermal evolution around $140^{\circ}C$ increases with lithiation and with decreasing particle size; this phenomenon is attributed to the thermal decomposition of the solid electrolyte interface (SEI) film. Exothermic peaks, following a broad peak at around $140^{\circ}C$, shift to a lower temperature with a decrease in particle size, indicating that the thermal stability of the lithiated Si electrode strongly depends on the Si particle size.

• Bulletin of the Korean Chemical Society
• /
• v.18 no.6
• /
• pp.612-618
• /
• 1997

$LiMn_2O_4$ powders were prepared by burning and subsequent calcination of PEG-metal nitrate precursor. After the burning stage of the precursor, some minor phases such as $Mn_2O_3$ (or $Mn_3O_4$), MnO, and carbonate were formed and single phases of $LiMn_2O_4$ were obtained by further calcinations above 400 ℃. From thermal analysis of the precursor, a violent thermal decomposition, which was indicated by a drastic weight loss accompanied by a sharp and strong exothermic peak, was observed and probably caused by an oxidation-reduction reaction between oxidizer and fuel. The formation of the minor phases could be explained in terms of the burning behavior of the precursor by employing valence concepts of propellant chemistry. The calcined powders were composed of submicron-sized but highly agglomerated particles and showed very broad particle size distribution.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.57.1-57.1
• /
• 2011

The effects of relative humidity on the properties of the porous $ZrO_2$ ceramics were investigated in terms of the curing behavior of phenolic resin as a binder. The $ZrO_2$ powders containing 5wt% of phenolic resin were conditioned in a consistent chamber condition at a temperature of $50^{\circ}C$ and different humidity levels (25, 50, 75, and 95%) for 1 h. The exposure of humid atmosphere caused changes of density and microstructure in the green bodies. The higher level the powders were exposed to the humid atmosphere, the lower green density was obtained and the more irregular microstructure was observed due to aggregation by the curing of phenolic resin. After firing, the porosity of specimens has risen from 35.7% to 38.1% and Young's modulus has declined in response to the variation of green density. These results could be explained by the degree of resin cure which was associated with the area under the exothermic peak enclosed by a baseline of DSC thermogram curve. Also, the curing behavior of phenolic resin according to relative humidity has been confirmed by decrease of ether groups which have interacted with the phenolic-OH group and the hexamine as a curing agent. Consequently, it could be demonstrated that increase the relative humidity during fabrication of porous $ZrO_2$ diminished the compaction and properties of specimens after firing owing to curing of phenolic resin.

• Polymer(Korea)
• /
• v.27 no.2
• /
• pp.120-128
• /
• 2003

The effects of catalyst, accelerator and blend composition on the cure behavior of unsaturated polyester resin (UPE), vinyl ester resin (VE) and their blends were studied using differential scanning calorimetry(DSC). The DSC thermograms strongly depend on each variable. The result shows that the small exothermic peak at 115$^{\circ}C$ is due mainly to the UPE component in the UPE/VE blends and the large one at 134~138 $^{\circ}C$ is due mainly to the VE component. The results also indicate that the change of the DSC thermogram measured after each blend was exposed to high temperature 18$0^{\circ}C$ and the fast curing conditions of a few tens seconds provide useful information on understanding the thermal processing of a blend at high speed. The measurements of resin flow time represent that there are three distinct stages of cure in the UPE/VE blends: induction, transition and macro-gelation stages, as similarly reported for UPE by others earlier. The thermal stability and flexural properties of the cured UPE are significantly improved by blending it with the VE, depending on the composition.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.4
• /
• pp.783-786
• /
• 2009

Thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and ion chromatography(IC) were employed to analyze the thermal behavior of $Li_xCoO_2$ cathode material of lithium ion battery. The mass loss peaks appearing between 60 and 125 ${^{\circ}C}$ in TGA and the exothermic peaks with 4.9 and 7.0 J/g in DSC around 75 and 85 ${^{\circ}C}$ for the $Li_xCoO_2$ cathodes of 4.20 and 4.35 V cells are explained based on disruption of solid electrolyte interphase (SEI) film. Low temperature induced HF formation through weak interaction between organic electrolyte and LiF is supposed to cause carbonate film disruption reaction, $Li_2CO_3\;+\;2HF{\rightarrow}\;2LiF\;+\;CO_2\;+\;H_2O$. The different spectral DSC/TGA pattern for the cathode of 4.5 V cell has also been explained. Presence of ionic carbonate in the cathode has been identified by ion chromatography and LiF reported by early researchers has been used for explaining the film SEI disruption process. The absence of mass loss peak for the cathode washed with dimethyl carbonate (DMC) implies ionic nature of the film. The thermal behavior above 150 ${^{\circ}C}$ has also been analyzed and presented.

• Korean Journal of Materials Research
• /
• v.22 no.7
• /
• pp.329-334
• /
• 2012

Two types of nanoclusters, termed Cluster (1) and Cluster (2) here, both play an important role in the age-hardening behavior in Al-Mg-Si alloys. Small amounts of additions of Cu and Ag affect the formation of nanoclusters. Two exothermic peaks were clearly detected in differential scanning calorimetry(DSC) curves by means of peak separation by the Gaussian method in the base, Cu-added, Ag-added and Cu-Ag-added Al-Mg-Si alloys. The formation of nanoclusters in the initial stage of natural aging was suppressed in the Ag-added and Cu-Ag-added alloys, while the formation of nanoclusters was enhanced at an aging time longer than 259.2 ks(3 days) of natural aging with the addition Cu and Ag. The formation of nanoclusters while aging at $100^{\circ}C$ was accelerated in the Cu-added, Ag-added and Cu-Ag-added alloys due to the attractive interaction between the Cu and Ag atoms and the Mg atoms. The influence of additions of Cu and Ag on the clustering behavior during low-temperature aging was well characterized based on the interaction energies among solute atoms and on vacancies derived from the first-principle calculation of the full-potential Korrinaga-Kohn-Rostoker(FPKKR)-Green function method. The effects of low Cu and Ag additions on the formation of nanoclusters were also discussed based on the age-hardening phenomena.

• Journal of the Korean Ceramic Society
• /
• v.48 no.4
• /
• pp.293-297
• /
• 2011

The thermodynamic behavior of phenolic resin was investigated to verify the relation between the properties of porous ceramics with $ZrO_2$-C system for submerged entry nozzle and the characteristics of phenolic resin with various relative humidity. The green and the sintered density were decreased between 25% and 50% relative humidity, whereas they were gradually enhanced above 50% relative humidity. The highest value of apparent porosity was 20.1% and the minimum compressive strength was 69MPa in the specimen using the powder exposed to 50% relative humidity. As a result of thermal analysis for phenolic resin, the shift of endothermic peak to low temperature and the reduction of exothermic peak were observed, and the peaks corresponded to melting and curing of phenolic resin, respectively. The melting and the curing of phenolic resin generate the change of green density, and it can affect the properties of submerged entry nozzle.

• Journal of Korea Foundry Society
• /
• v.15 no.6
• /
• pp.566-573
• /
• 1995

In this study, the microstructural characteristics such as primary silicon, eutectic silicon, $SiC_p$ dispersion behavior, compound amount and Si solubility in $Al/SiC_p$ composite fabricated by the squeeze casting under various conditions were investigated systematically. As applied pressure(MPa) increases, cooling rate and compound amount are increased. In gravity casting, the cooling rate of hypereutectic composite is slower than of hypoeutectic composite by exothermic reaction of primary Si crystallization. But the cooling rate of hypereutectic composite is faster than that of hypoeutectic composite fabricated by same applied pressure, because amount of primary Si crystallization in hypereutectic composite was decreased, on the contrary, primary ${\alpha}-Al$ in hypoeutetic composite was increased due to increase of Si solubility in matrix by applied pressure. The crystalized primary silicon in hypereutectic composite fabricated by squeeze casting become more fine than that in non-pressure casting This is because mush zone became narrow due to increase of Si content of eutectic composition by pressure and time for growth of primary silicon got shorter according to applied pressure. It is turned out that eutectic temperature and liquidus are decreased by the increasing of squeeze pressure in all the composite due to thermal unstability of matrix owing to increasing of Si solubility in matrix by the increasing of applied pressure, as indicated in thermal anaiysis(DSC) results.