• Journal of the Korean Geotechnical Society
• /
• v.19 no.6
• /
• pp.107-114
• /
• 2003

Among soft ground treatment methods with granular soil used in domestic, the sand compaction pile method has been utilized greatly, but, as a result of exhaustion of sand and increase of unit cost, the necessity of an alternative method is suggested. In this study, the static load tests for crushed-stone compaction piles which were constructed on test field were performed. Based on test results, stress concentration ratios between the crushed-stone compaction pile and the soft ground were investigated and estimated. At loading pressure, settlement showed decreasing tendency as replacement rate increases. At replacement rate of 20%, yield pressure was smaller but, at replacement rates of 30% and 40%, settlement and yield pressure were similar. The stress concentration ratio was within the range of 1.7 to 3.0 and it was higher as replacement rate increased.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.705-712
• /
• 2005

Among soft ground treatment methods with granular soil used in domestic, the sand compaction pile method has been utilized greatly, but, as a result of exhaustion of sand and increase of unit cost, a necessity of an alternative method is suggested. In this study, the static load tests for group crushed-stone compaction piles which were constructed at in-situ site were performed. Pile diameter was 700mm and area of loading plates were changed. The static load tests of single and group piles were performed for area replacement ratio of 20, 30 and 40%. Based on test results, bearing capacity of group crushed-stone compaction pile were estimated. The more both single pile and group pile increase, the more yield bearing capacity tended to increase. Also, the yield bearing capacity of a group pile is about 50% less than the yield bearing capacity of a single pile. If the ground reinforced with the crushed-stone compaction pile is replacement ratio of $20{\sim}40%$, RIYB of both single pile and group pile increases qualitative tendency of linear more than original ground

• Fibers and Polymers
• /
• v.4 no.3
• /
• pp.124-128
• /
• 2003

Dark brown Alpaca fiber was reduced in shade via selective bleaching with peroxide. Two selective oxidative bleaching methods were tested on alpaca top to assess their effectiveness for color removal and fiber quality properties. Color change, bundle strength, weight loss, fiber diameter, surface modification, dye-ability and dye wash fastness were assessed for both methods and compared with the original brown top. Bleach method 1 (BL-I) showed little surface modification, 5.8% weight loss and 2.4% strength loss. D1925 yellowness index was reduced to 74.3 from 83.1 and provided a good base for the dyeing of medium to deep shades. Bleach method 2 (BL-II) displayed considerable surface modification, 7.8% weight loss and 18% strength loss. BL-II also resulted in a mean diameter reduction of 1.9 micron during bleaching. Yellowness was reduced to 64.5 from 83.1 and provided a very good base for the dyeing of medium to deep shades. BL-I showed better exhaustion of the premetallised dye Lanaset Violet B than BL-II. Wash fastness for BL-II was 1 grey scale unit poorer than BL-I. BL-II showed far better color clarity at pale depths however the wash fastness of the finished product was not good enough to maintain the depth or clarity of the color. BL-I showed poorer clarity of color but exhibited better wash fastness results.

• Industrial Engineering and Management Systems
• /
• v.8 no.1
• /
• pp.66-71
• /
• 2009

This study proposes a new framework for designing disassembly methods. In recent years, environmental problems have become global issues. Recycling of used products or resources is recognized as a matter of significance since it may help reduce the risk of exhausting natural resources. Considering possible exhaustion of limited natural resources in the near future, reuse of products would gain more environmental significance. As yet, it relies hugely on manual disassembly, which labor cost places burden on the total recycling cost. The purpose of this study is to propose a methodology designing for manual disassembly works, and a creation method of a jig. By focusing on parts' connection and attachment relationship, parts are categorized in 5 categories (parent part, joint key part, attaching key part, child part, and independent part) according to the features that parts possess, and 3 kinds of connection relationships (parent part-joint key part connection, parent part-independent part connection and child part-child part connection) are clarified. Connection relationship and attachment relationship charts have also been created, and utilizing them, disassembly orders are settled, and a disassembly jig is devised. The proposed methodology is also applied to a real product and its work time is improved 42% form 31 to 13 seconds.

• Transactions of the Korean hydrogen and new energy society
• /
• v.17 no.2
• /
• pp.218-226
• /
• 2006

It can be obtained from hydrocarbon and water, specially production of hydrogen from natural gas is most commercial and economical process among the hydrogen production methods, and has been used widely. However, conventional hydrogen production methods are dependent on fossil fuel such as natural gas and coal, and it may be faced with problems such as exhaustion of fossil fuels, production of greenhouse gas and increase of feedstock price. Thermochemical hydrogen production by nuclear energy has potential to efficiently produce large quantities of hydrogen without producing greenhouse gases. However, nuclear hydrogen must be economical comparing with conventional hydrogen production method. Therefore, hydrogen production cost was analyzed and estimated for nuclear hydrogen as well as conventional hydrogen production such as natural gas reforming and coal gasification in various range.

• Textile Coloration and Finishing
• /
• v.16 no.5
• /
• pp.1-7
• /
• 2004

Because acid dyes and reactive dyes require acidic condition for adsorption and alkaline condition for fixation respectively, it is difficult to dye nylon/cotton blends in one-bath one-step dyeing method. In this paper we tried to find out the suitable dye and dyeing condition for one-bath one-step dyeing of nylon/cotton blends. MNT type reactive dyes showed higher exhaustion on cotton as compared with MCT type dyes at neutral pH, which means that the MNT type reactive dyes are preferable for one-bath one-step dyeing method. The optimum condition for one-bath one-step dyeing of nylon/cotton blends was found to be pH 7. Wash fastness of fabrics dyed with half-milling type acid dyes was superior to that of fabrics dyed with levelling type acid dyes, when MNT type reactive dyes were used together.

• Applied Chemistry for Engineering
• /
• v.4 no.4
• /
• pp.760-769
• /
• 1993

Solvent-free low foaming scouring agents(LFSA) were prepared by blending of polyoxyethylene(30) octadecylbenzylammonium chloride(POAC), block copolymer of propylene oxide-ethylene oxide[p(PO-b-EO) glycol], Sedlan FF-200(FF-200) and sulfonic acid-amine condensate of polyoxyethylene(10) nonylphenyl ether(PSAC). In consequence of several tests, FF-200/POAC/p(PO-b-EO) glycol/PSAC/water (20g/10g/5g/5g/60g) mixture (LFSA-5) showed good cleaning power, penetrating ability, emulsifiability and stability to alkali, and gave less problem in water pollution. Scouring effect of LFSA-5 was investigated by the change of percentage of exhaustion before and after scouring at various dyeing temperatures. The percentage of exhaustion of the unscoured PET fabric was 4.5% at $70^{\circ}C$, while that scoured with LFSA-5 was 1.3% at the same temperature, which proved LFSA-5 to be a good scouring agent. Moreover, the foaming power of LFSA-5 measured by Ross and Miles method was 6mm foam height immediately after foaming, and that measured by Ross and Clark method was less than 300mm foam height at $30^{\circ}C$, and 20mm at $80^{\circ}C$. As a result, LFSA-5 proved a good low foaming scouring agent.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.5
• /
• pp.394-405
• /
• 2019

The purpose of this study is to clarify the concept of the frail elderly and to obtain theoretical evidence. The research method was conducted using the basic principles for conceptual analysis of Walker and Avant(2005). As a Result of a review of the literature about how to utilize the concept of a frail elderly, frail elderly might be in the intermediate state of health and disease. They can be defined as physically vulnerable in the sarcopenia, inflammation, insulin resistance, and preceding advanced disease, lead to hospitalization, falls, disability, and death. The attributes were physiological, psychological, and socio-environmental and economic factors, so they had multidimensional factors. They were required the assist daily living of another person. Also, their attributes had decreased the amount of recovery time and degree, and exhaustion. The attributes of frail elderly consisted of these facts: dynamic process, multidimensional factors, dependency, vulnerability. The frail elderly was a dynamic process that involves the possibility of change to health and disease, and include physical, mental, cognitive, and social environmental factors. In addition, the frail elderly was difficulty in daily life, physical vulnerability and difficulty in adaption. In conclusion, frail elderly as defined by the results of this study will contribute to the foundation of health care systems, including community visiting nursing to understand the level of frail elderly and systemic management to do not go into long term care.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.12B
• /
• pp.1514-1523
• /
• 2009

It is well known that the current wireless sensor networks addressing methods do not work efficiently in networks more than a few hundred nodes. A standard protocol in ZigBee-Standard feature in ZigBee 2007 gives balanced tree based address assignment method with distributed manner. However, it was limited to cover less than hundreds of sensor nodes due to the wasteful use of available address space, because composed sensor networks usually make an unbalanced tree topology in the real deployment. In this paper, we proposed the hierarchical cluster tree based address assignment method to support large and scalable networks. This method provides unique address for each node with distributed manner and supports hierarchical cluster tree on-demand. Simulation results show that the proposed method reduces orphan nodes due to the address exhaustion and supports larger network with limited address space compared with the ZigBee distributed address assignment method defined in ZigBee-Standard feature in ZigBee 2007.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.5
• /
• pp.129-135
• /
• 2010

It is well known that distributed generation(DG) system using renewable energy is an alternative to solve the problems which result from the exhaustion of fossil fuel and the environmental pollution. A PWM inverter is required for a power flow control in the DG systems. This paper proposes a SRF power flow control method considering grid impedance in grid-connected single-phase inverter systems. The proposed SRF power flow control method can provide a voltage-reference for the single-phase inverter even without any grid impedance estimation so that the single-phase inverter system could operate in stand-alone mode and grid-connected mode based on the known nominal value of grid impedance. Also independent controls of active and reactive power are achieved by the proposed control method. The effectiveness and the validity of the proposed control method are demonstrated through simulations. The simulation results show that the proposed control method can control properly power flow in grid-connected single-phase inverter systems.