• Nuclear Engineering and Technology
• /
• v.53 no.4
• /
• pp.1331-1344
• /
• 2021

This study is to evaluate the seismic capacity of the fire-damaged cabinet facility in a nuclear power plant (NPP). A prototype of an electrical cabinet is modeled using OpenSees for the numerical simulation. To capture the nonlinear behavior of the cabinet, the constitutive law of the material model under the fire environment is considered. The experimental record from the impact hammer test is extracted trough the frequency-domain decomposition (FDD) method, which is used to verify the effectiveness of the numerical model through modal assurance criteria (MAC). Assuming different temperatures, the nonlinear time history analysis is conducted using a set of fifty earthquakes and the seismic outputs are investigated by the fragility analysis. To get a threshold of intensity measure, the Monte Carlo Simulation (MCS) is adopted for uncertainty reduction purposes. Finally, a capacity estimation model has been proposed through the investigation, which will be helpful for the engineer or NPP operator to evaluate the fire-damaged cabinet strength under seismic excitation. This capacity model is presented in terms of the High Confidence of Low Probability of Failure (HCLPF) point. The results are validated by the proper judgment and can be used to analyze the influences of fire on the electrical cabinet.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.26 no.1
• /
• pp.60-67
• /
• 2022

A study was conducted to analyze the behavioral change of the kerosene flame ultrasonically-atomized under an ultrasonic standing-wave. Combustion region was visualized through DSLR, ICCD camera and the Schlieren photography with high-speed camera. The fuel consumption was measured by a precise scale. As a result, in the case of ultrasonic standing-wave excitation, it was observed that the intensity of OH radical(OH^*) was enhanced and optimal combustion condition was formed around the upper edge of the standing-wave field.

• Smart Structures and Systems
• /
• v.31 no.5
• /
• pp.455-467
• /
• 2023

Impact damper is a passive damping system that controls undesirable vibration with mass block impacting with stops fixed to the excited structure, introducing momentum exchange and energy dissipation. However, harmful momentum exchange may occur in the random excitation increasing structural response. Based on the mechanism of impact damping system, a semi-active impact damper (SAID) with controllable impact timing as well as a semi-active control strategy is proposed to enhance the seismic performance of engineering structures in this paper. Comparative experimental studies were conducted to investigate the damping performances of the passive impact damper and SAID. The extreme working conditions for SAID were also discussed and approaches to enhance the damping effect under high-intensity excitations were proposed. A numerical simulation model of SAID attached to a frame structure was established to further explore the damping mechanism. The experimental and numerical results show that the SAID has better control effect than the traditional passive impact damper and can effectively broaden the damping frequency band. The parametric studies illustrate the mass ratio and impact damping ratio of SAID can significantly influence the vibration control effect by affecting the impact force.

• The Bulletin of The Korean Astronomical Society
• /
• v.44 no.2
• /
• pp.40.3-40.3
• /
• 2019

Our recent observations of the Sun through strong spectral lines have revealed several important properties of the three-minute umbral oscillations inside sunspots -- the oscillations of intensity and Doppler velocity with periods of 2 to 3 minutes. The oscillations usually occur in the form of a time series of oscillation packets each of which lasts 10 to 20 minutes, not as continuous trains. Each oscillation packet is characterized by a singly peaked power spectrum of velocity oscillation. The oscillations propagate in the vertical direction from the photosphere to the corona. In the upper chromosphere, they develop into shocks that eventually collide with the transition region. When shocks propagate along a highly inclined direction, the merging of two successive shocks can take place. Once they enter the corona, they change to linear compressional waves. In the image plane, the three-minute oscillations propagate with high speeds in the transverse direction as well, usually propagating radially outwards from a point, and sometimes accompanying spiraling patterns of Doppler velocity. These observational properties can be theoretically explained by postulating the spatio-temporally localized source of fast MHD waves at a depth of about 2000 km below the surface, the excitation of slow MHD waves via mode conversion near the photosphere, and the resonance of the slow waves in the photospheric layer below the temperature minimum, and the nonlinear development of slow waves in the chromosphere.

• Applied Chemistry
• /
• v.15 no.1
• /
• pp.29-32
• /
• 2011

Surfactant enhanced fluorescence (FL) of europium-salicylic acid (SA) complex has been studied. It was observed that weak FL of Eu(III) at the wavelength of 589 nm and 612 nm was found to be enhanced after addition of salicylic acid and cetyltrimethylammonium bromide (CTAB) surfactant upon excitation at 395 nm. Under optimized condition, FL intensity of Eu(III) at 612 nm responded linearly with the concentration of SA in the range of 5.5×10^-9 to 1.5×10^-6 M of SA. The detection limit was calculated from the calibration curve(3Sb/m) as 9.27×10^-9 M.

• Korean Journal of Ecology and Environment
• /
• v.44 no.3
• /
• pp.292-302
• /
• 2011

The Lake Sihwa watershed includes industrial, urban, and rural areas simultaneously. In this study, we analyzed the characteristics of dissolved organic matter (DOM) in spatial-temporal runoff patterns at representative sites having different land use in the watershed of Lake Sihwa. The result of synchronous and 3D-EEMs(3-Dimensional Excitation Emission Matrix Spectroscopy) analysis in 4TG (industrial area), fluorescence distribution and variation clearly appeared in the Fulvic-like fluorescence (FLF) and Humic-like fluorescence (HLF) regions along with the Protein-like fluorescence (PLF) region. A characteristic that Peak A (HLF) region fluorescence intensity did not decrease and the HLF region of fluorescence intensity and spatial-temporal changes clearly appeared during rainfall in AS (urban area). The results of fluorescence analysis in MS did not show great changes in PLF and FLF while showing that fluorescence intensity changes over time in the Terrestrial-like fluorescence (THLF) region increased greatly. In conclusion, our results showed significant differences in the runoff characteristics of DOM particularly in industrial, urban and rural area, and these differences should be considered for the efficient controlling of DOM in the watershed.

• Journal of the Korean Society of Radiology
• /
• v.6 no.5
• /
• pp.351-356
• /
• 2012

Ultrasonic cavitation is a physical phenomenon that generates and collapses microbubbles in media (mainly fluids) under conditions of strong ultrasonic irradiation. In this study, changes in the ultrasonic acoustic characteristics of bubble clouds in relation to ultrasonic irradiation were observed by the quantitative evaluation of cavitation yields. Concave-type single ultrasonic transducers with center frequencies of 500 kHz and 1.1 MHz were used to produce cavitation, and 2.25 MHz interference ultrasonic waves that would traverse any bubble clouds generated were used to analyze the cavitation. The parameters used for the evaluation of cavitation yields (changes in the center frequency, attenuation characteristics, and the propagation time of penetrating waves) were analyzed in relation to the cavitation-generating conditions (irradiation intensity, excitation signal, and center frequency). On the basis of these results, correlations between the changes in the center frequency and irradiation intensity were identified. Although the correlation coefficient was low, notable changes were observed in the center frequency under certain irradiation conditions. Attenuation trends in the interference ultrasonic waves showed high correlations with all the irradiation conditions, and it was noted that these trends were not affected by the forms of cavitation generated. No differences in the propagation time were observed among different irradiation conditions. These findings suggest that bubble yields can be quantitatively evaluated effectively by evaluating the diverse irradiation conditions and that such a quantitative evaluation could be used to study the basic cavitation phenomenon occurring in high-intensity ultrasonic wave treatment.

• Analytical Science and Technology
• /
• v.25 no.3
• /
• pp.197-206
• /
• 2012

Ambers are composed of polymer molecules which contain aromatic moieties such as benzene, naphthalene, phenanthrene and anthracene. They emit fluorescence when irradiated with ultraviolet light, which was used for confirming an amber. The fluorescence of amber, however, tends to decrease as the surface of amber is weathered with light, heat, oxygen for a long time. In this study, the reliability of confirming amber with its fluorescence by measuring the changes of fluorescence after artificial aging. Aging factors were UV light (${\lambda}$=340 nm), oxygen with heat (100%, $90^{\circ}C$) and heat ($90^{\circ}C$) and aging time was for 5, 15, 30 and 60 days, respectively. In the excitation and emission spectra of amber, the intensity decreased and the maximal wavelength was shifted to longer wavelength with artificial aging time. Especially, there was a drastic decrease in the intensity of spectra to 1.7% of initial value after 60 days aging under oxygen with heat. Only in Colombian amber there showed an increase of fluorescence intensity for a certain aging time, which could be explained by the production of aromatic ring in the presence of light and heat. Conclusively, the fluorescence can be lessened by the natural weathering with light, heat and oxygen and it is not accurate to recognize amber just with UV irradiation method.

• Korean Journal of Ecology and Environment
• /
• v.45 no.1
• /
• pp.42-51
• /
• 2012

This study investigated the characteristics of natural organic matter (NOM) with general water characteristics (pH, DO, electrical conductivity, BOD, COD, TN, TP, Chl-$a$, DOC, $UV_{254}$, SUVA) and the 3D fluorescence excitation-emission matrix (FEEM) in the Yeongsan River basin. FEEM was used to classify protein-like and fulvic & humiclike substances with fluorescence intensity in the matrix of excitation and emission wavelength. The concentration of BOD, COD, TN, electrical conductivity and DOC in the region of Gwangju city (Gwangju sewage treatment plant: GJS, Gwangjucheon: GJC, Gwangju 2: GJ2) was relatively higher than the upper reaches and lower reaches of the Yeongsan River basin. SUVA in most sites was lower than 3 L $mg^{-1}\;m^{-1}$ as the hydrophilic substances, except Damyang (DY) in the upper reaches of Yeongsan river was higher than 3 L $mg^{-1}\;m^{-1}$ as the hydrophobic substances during winter and autumn. In the FEEM investigation the fulvic and humic substances were found in most sites, and in sites regarding Gwangju city (GJS, GJC, GJ2) during winter and GJC in summer, protein-like substances were found. The trend of fluorescence intensities from the upper reaches to the lower reaches in most sites corresponded to that regarding the concentration of water characteristics (BOD, COD, TN, DOC). That is why the region of Gwangju city (GJS, GJC, GJ2) was relatively higher. This results were an equivalent trend to those of fluorescence index (FI) in most sites, and the higher FIs in the sites of Gwangju city indicate more microbial-derived substances due to enormous effluent organic matters (EfOM) from huge Gwangju sewage treatment plants.

• Journal of the Korean Ceramic Society
• /
• v.42 no.3 s.274
• /
• pp.145-149
• /
• 2005

[ $Eu^{2+}$ ]-activated barium magnesium silicate phosphor, $(Ba,Ca)_{3}MgSi_{2}O_{8}:Eu_{x}$, has been known to emit blue-green light. In this study we report the manufacturing processes for producing either pure green or pure blue light-emitting phosphor from the same composition of $Ba_{2-x}Ca_{2}CaMgSi_{2}O_{8}:Eu_{x}$ (0 < x < 1) by controlling heat treatment conditions. Green light emitting phosphor of $Ba_{1.9}CaMgSi_{2}O_{8}:Eu_{0.1}$ can be produced under the sample preparation condition of highly reducing atmosphere of $23\%\;H_2/77\%\;N_2$, while blue or blue-green light emitting phosphor under reducing atmosphere of $5\~20\%\;H_2\;/\;95\~80\%$ N_2. The green light-emitting phosphors are prepared in two steps: firing at $800\~1000^{\circ}C$ for $2\~5$ h in air then at $1100\~1350^{\circ}C$ for 2-5 h under reducing atmo­sphere $23\%$ $H_2/77\%\;N_2$. The excitation spectrum of the green light-emitting phosphor shows a broadband of $300\~410$ nm. The emission spectrum has a maximum intensity at the wavelength of about 501 nm. The CIE value of green light emission is (0.162, 0.528). The pure blue light-emitting phosphors can be produced using the $Ba{2_x}CaMgSi_{2}O_{8}:Eu_{x}$ by introducing additional firing step at $1150\~1300^{\circ}C$ in air before the final reducing treatment. The XRD analysis shows that the green light-emitting phosphor mainly consisted of $Ba_{1.31}Ca_{0.69}SiO_{4}$ (JCPDS $\#$ 36-1449) and other minor phases i.e., $MgSiO_3$ (JCPDS $\#$ 22-0714) and $Ca_{2}BaMgSi_{2}O_{8}$ (JCPDS $\#$ 31-0128). The blue light-emitting phosphor mainly consisted of $Ca_{2}BaMgSi_{2}O_{8}$ phase.