• International conference on construction engineering and project management
• /
• 2015.10a
• /
• pp.656-657
• /
• 2015

Recently, Multi-Objective Optimization of design elements is an important issue in building design. Design variables that considering the specificities of the different environments should use the appropriate algorithm on optimization process. The purpose of this study is to compare and analyze the optimal solution using three evolutionary algorithms and energy modeling simulation. This paper consists of three steps: i)Developing three evolutionary algorithm model for optimization of design elements ; ii) Conducting Multi-Objective Optimization based on the developed model ; iii) Conducting comparative analysis of the optimal solution from each of the algorithms. Including Non-dominated Sorted Genetic Algorithm (NSGA-II), Multi-Objective Particle Swarm Optimization (MOPSO) and Random Search were used for optimization. Each algorithm showed similar range of result data. However, the execution speed of the optimization using the algorithm was shown a difference. NSGA-II showed the fastest execution speed. Moreover, the most optimal solution distribution is derived from NSGA-II.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.2
• /
• pp.471-477
• /
• 2014

The novel permanent magnetic actuator (PMA) and its optimal design method were proposed in this paper. The proposed PMA is referred to as the separated permanent magnetic actuator (SPMA) and significantly superior in terms of its cost and performance level over a conventional PMA. The proposed optimal design method uses the evolutionary strategy algorithm (ESA), the kriging meta-model (KMM), and the multi-step optimization. The KMM can compensate the slow convergence of the ESA. The proposed multi-step optimization process, which separates the independent variables, can decrease time and increase the reliability for the optimal design result. Briefly, the optimization time and the poor reliability of the optimum are mitigated by the proposed optimization method.

• Journal of Institute of Control, Robotics and Systems
• /
• v.10 no.11
• /
• pp.1071-1076
• /
• 2004

It is a fuzzy controller that it is the most used method in the control of non-linear system. The most important part in the fuzzy controller is a design of fuzzy rules. Many algorithm that design fuzzy rules have proposed. And attention to the evolutionary computation is increasing in the recent days. Among them, the co-evolutionary algorithm is used in the design of optimal fuzzy rule. This paper takes advantage of a schema co-evolutionary algorithm. In order to verify the efficiency of the schema co-evolutionary algorithm, a fuzzy controller for the mobile robot control is designed by the schema co-evolutionary algorithm and it is compared with other parasitic co-evolutionary algorithm such as a virus-evolutionary genetic algorithm and a co-evolutionary method of Handa.

• Earthquakes and Structures
• /
• v.1 no.3
• /
• pp.289-306
• /
• 2010

A gradient-based evolutionary optimization methodology is presented for finding the optimal design of viscous dampers to minimize an objective function defined for a linear multi-storey structure. The maximum value along height of the transfer function amplitudes for the interstorey drifts is taken as the objective function. Since the ground motion includes various uncertainties, the optimal damper placement may be different depending on the ground motion used for design. Furthermore, the transfer function treated as the objective function depends on the properties of structural parameters and added dampers. This implies that a more robust damper design is desired. A reliable and robust damping design system against any unpredictable ground motions can be provided by minimizing the maximum transfer function. Such design system is proposed in this paper.

• Structural Engineering and Mechanics
• /
• v.43 no.6
• /
• pp.771-794
• /
• 2012

This paper presents a multi-objective evolutionary algorithm for combinatorial optimisation and applied for design optimisation of fiber reinforced composite structures. The proposed algorithm closely follows the implementation of Pareto Archive Evolutionary strategy (PAES) proposed in the literature. The modifications suggested include a customized neighbourhood search algorithm in place of mutation operator to improve intensification mechanism and a cross over operator to improve diversification mechanism. Further, an external archive is maintained to collect the historical Pareto optimal solutions. The design constraints are handled in this paper by treating them as additional objectives. Numerical studies have been carried out by solving a hybrid fiber reinforced laminate composite cylindrical shell, stiffened composite cylindrical shell and pressure vessel with varied number of design objectives. The studies presented in this paper clearly indicate that well spread Pareto optimal solutions can be obtained employing the proposed algorithm.

• Structural Engineering and Mechanics
• /
• v.34 no.5
• /
• pp.581-595
• /
• 2010

This paper presents topology optimization of geometrically and materially nonlinear structures using a bi-directional evolutionary optimization (BESO) method. To maximum the stiffness of nonlinear structures under prescribed design load, the complementary work is selected as the objective function of the optimization. An optimal design can be obtained by gradually removing inefficient material and adding efficient ones. The proposed method can be applied to a series of geometrically and/or materially nonlinear structures. The results show considerable differences in topologies and stiffness of the optimal designs for linear and nonlinear structures. It is found that the optimal designs for nonlinear structures are much stiffer than those for linear structures when large design loads (which result in significantly nonlinear deformations) are applied.

• Wind and Structures
• /
• v.32 no.1
• /
• pp.71-80
• /
• 2021

In steel cable bridges, the use of magnetorheological (MR) dampers between butt cables is constantly increasing to dampen vibrations caused by rain and wind. The biggest problem in the actual applications of those devices is to launch a kind of appropriate algorithm that can effectively and efficiently suppress the perturbation of the tie through basic calculations and optimal solutions. This article discusses the optimal evolutionary design based on a linear and quadratic regulator (hereafter LQR) to lessen the perturbation of the bridges with cables. The control numerical algorithms are expected to effectively and efficiently decrease the possible risks of the structural response in amplification owing to the feedback force in the direction of the MR attenuator. In addition, these numerical algorithms approximate those optimal linear quadratic regulator control forces through the corresponding damping and stiffness, which significantly lessens the work of calculating the significant and optimal control forces. Therefore, it has been shown that it plays an important and significant role in the practical application design of semiactive MR control power systems. In the present proposed novel evolutionary parallel distributed compensator scheme, the vibrational control problem with a simulated demonstration is used to evaluate the numerical algorithmic performance and effectiveness. The results show that these semiactive MR control numerical algorithms which are present proposed in the present paper has better performance than the optimal and the passive control, which is almost reaching the levels of linear quadratic regulator controls with minimal feedback requirements.

• Advances in Computational Design
• /
• v.6 no.1
• /
• pp.31-42
• /
• 2021

This research aims to demonstrate the optimal geometrical design of splayed multiple cross-sectional pin fin heat sinks (SMCSPFHS), which are a type of side-inlet-side-outlet heat sink (SISOHS). The optimiser strength Pareto evolutionary algorithm2 (SPEA2)is employed to explore a set of Pareto optimalsolutions. Objective functions are the fan pumping power and junction temperature. Function evaluations can be accomplished using computational fluid dynamics(CFD) analysis. Design variablesinclude pin cross-sectional areas, the number of fins, fin pitch, thickness of heatsink base, inlet air speed, fin heights, and fin orientations with respect to the base. Design constraints are defined in such a way as to make a heat sink usable and easy to manufacture. The optimum results obtained from SPEA2 are compared with the straight pin fin design results obtained from hybrid population-based incremental learning and differential evolution (PBIL-DE), SPEA2, and an unrestricted population size evolutionary multiobjective optimisation algorithm (UPSEMOA). The results indicate that the splayed pin-fin design using SPEA2 issuperiorto those reported in the literature.

• Proceedings of the KIEE Conference
• /
• 2004.04a
• /
• pp.21-23
• /
• 2004

In this paper, an optimal design method to have good performance is researched. The parameters which are sensitive to the performance are examined and selected by using evolutionary computations and commercial CAD program to have good performance. Design method Simulated are compared with conrrentional procedure.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.14 no.2
• /
• pp.228-233
• /
• 2004

Nowadays, the robot with various and complex functions is required. previous algorithms, however, cannot satisfy the requirement. In order to solve these problems, we introduce the 2-Layer Fuzzy Controller, which has a small number of fuzzy rules corresponding to various inputs and outputs. Also, it controls robustly and effectively an object. The main problem in the fuzzy controller is how to design the fuzzy rule. This paper designs the optimal 2-layer fuzzy controller using the Schema Co-Evolutionary Algorithm. The schema co-evolutionary algorithm can find more rapidly and excellently than simple genetic algorithm does.