• Journal of Animal Environmental Science
• /
• v.14 no.2
• /
• pp.105-112
• /
• 2008

This study was carried out to investigate evaporation rate of moisture per surface area and degradation rate of organic matter in full scale escalator reversing composting facility were analyzed to develope a computer program for the computation of an optimum volume of composting facility according to handling methods of swine farm, moisture levels of manure, degradation rate of organics and evaporation rate of moisture during composting. The obtained results can be followed as bellow; The temperature in full scale escalator reversing composting facility during composting reached $70^{\circ}C$ in 4 days and maintained until 11 days. Reduction rate of moisture and density was average 1.20% and 29.7%, respectively. Annual degradation rate of organic matter was 3.53%, showing lowest rate in winter as 3.23%. These seasonal degradation rate could be a factor to be considered for proper management and installation of composting facility. When computed with the amount of feces, urine, slurry and manure plus wastewater produced, the optimum volumes of composting facility for slurry and manure plus wastewater including each 95% moisture was $229m^3$ and $277m^3$, respectively, showing 21% ($48m^3$) difference.

• Solar Energy
• /
• v.20 no.2
• /
• pp.43-54
• /
• 2000

We prepared and characterized $Cu(In_{1-x}Ga_x)Se_2$(CIGS) films using a elemental co-evaporation method for absorbing layer of high efficiency thin film solar cells. The CIGS films deposited on a soda-lime glass exhibited low resistivity because of higher carrier concentration. Na was accumulated at the CIGS surface and the 0 and Se were also accumulated at the surface, suggesting that oxidation is a driving force of Na accumulation. The structure of CIGS film was modified or a secondary phase was formed in the Cu-poor CIGS bulk films probably due to the incorporation of Na into Cu vacancy sites. As the Ga/(In+Ga) ratio increased, the diffraction peaks of $Cu(In_{1-x}Ga_x)Se_2$ films were shifted to larger angle and splitted, and the grain size of $Cu_{0.91}(In_{1-x}Ga_x)Se_2$ films became smaller. All $Cu_{0.91}(In_{1-x}Ga_x)Se_2$ films showed the p-type conductivity regardless of the Ga/(In+Ga) ratio. Ag/n-ZnO/i-ZnO/CdS/$Cu_{0.91}(In_{0.7}Ga_{0.3})Se_2$/Mo solar cells were fabricated. The currently best efficiency in this study was 14.48% for $0.18cm^2$ area ($V_{oc}=581.5mV,\;J_{sc}=34.88mA$, F.F=0.714).

• Journal of the Korean Geotechnical Society
• /
• v.28 no.3
• /
• pp.55-66
• /
• 2012

To investigate the hysteresis of the suction stress in unsaturated weathered mudstone soils (CL), matric suction and volumetric water content were measured in both drying and wetting processes using Automated Soil-Water Characteristics Curve Apparatus. The drying and wetting processes in unsaturated soils were reproduced in the test; the drying process means to load matric suction to spill pore water from the soils, and the wetting process means to unload matric suction to inject pore water into the soils. Based on the measured result, Soil Water Characteristic Curve(SWCC)s were estimated by van Genuchten model (1980). SWCCs have nonlinear relationship between effective degree of saturation and matric suction. The hysteresis in SWCCs between drying and wetting processes occurred. As a result of estimating Suction Stress Characteristic Curve(SSCC) using Lu and Likos model (2006), the suction stress rapidly increased in the low level of matric suction and then increased slightly. Also, the hysteresis in SSCCs between drying and wetting processes occurred. In order to design geo-structures and check its stability considering unsaturated soil mechanics, therefore, it is more reasonable that the SSCC of drying process should be applied in the condition of rainfall infiltration and the SSCC of wetting process in the condition of evaporation or drainage.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.2
• /
• pp.203-210
• /
• 2000

The preparative methods of a chitosan-deposited activated carbon and its characteristics were studied by using three kinds of chitosan with different degree of deacetylation and average molecular weight. The procedure was consisted of the dissolution of chitosan into acid solution, impregnation of activated carbon, agitation, evaporation, and drying. When the chitosan-dissolved acid and its concentration, amounts of chitosan deposited, and agitation conditions were changed, the specific surface area, deposition state on surface, and stability were investigated, and amounts of Cr(VI) adsorbed was measured. In the preparation process, it was proper to agitate the chitosan-dissolved acetic acid solution at room temperature for 1hr. In the deposition of chitosan with low molecular weight, the specific surface area of activated carbon was greatly decreased even at low chitosan loading, but in the case of high molecular weight it was not nearly changed to 10wt% loading. It was known that chitosan was uniformly and physically deposited on activated carbon. The chitosan-deposited activated carbon was stable into the solution over about pH 6. The removal of Cr(VI) was remarkably enhanced by adding the adsorption function of chitosan to the surface of activated carbon with about 5wt% chitosan. It may be therefore used as an adsorbent for removing the pollutants in air and wastewater.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.12
• /
• pp.8165-8175
• /
• 2015

In Korea, summer is hot and humid, and air-conditioners consume lots of electricity. In such case, simultaneous usage of indirect evaporative cooler may reduce the sensible heat and save the electricity. In this study, heat transfer and pressure drop characteristics of indirect evaporative cooler made of aluminum, plastic, plastic/paper are investigated both under dry or wet condition. Results show that indirect evaporation efficiencies of the plastic/paper sample (38.5% ~ 51.4%) are approximately the same as those of the aluminum sample (41.9% ~ 47.5%), and are larger than those of the plastic sample (29.0% ~ 37.4%). This suggests that the plastic/paper sample could be a good substitute to the aluminum sample. However, the pressure drops across the paper channel are 92% ~ 106% larger than those across the aluminum channel. The heat transfer coefficients of the paper channel under dry condition are 15% ~ 44% larger than those of the plastic channel. The increases are 185% ~ 203% for the aluminum channel. The pressure drops of the paper channel are 34% ~ 48% larger than those of the plastic channel and 93% ~ 106% larger than those of the aluminum channel. Rigorous heat transfer analysis reveals that, for the plastic sample, 30% ~ 37% of the wet channels remain dry, whereas all the channels are wet for plastic/paper sample. For aluminum sample, the ratio is 17% ~ 23%.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.1
• /
• pp.53-60
• /
• 2011

In this study, an organic Rankine-cycle system using HFC-134a, which is a power cycle corresponding to a low-temperature heat source, such as that for geothermal power generation, was investigated from the view point of power optimization. In contrast to conventional approaches, the heat transfer and pressure drop characteristics of the working fluid within the heat exchangers were taken into account by using a discretized heat exchanger model. The inlet flow rates and temperatures of both the heat source and the heat sink were fixed. The total heat transfer area was fixed, whereas the heat-exchanger areas of the evaporator and the condenser were allocated to maximize the power output. The power was optimized on the basis of three design parameters. The optimal combination of parameters that can maximize power output was determined on the basis of the results of the study. The results also indicate that the evaporation process has to be optimized to increase the power output.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.23 no.4
• /
• pp.393-399
• /
• 2005

Since vegetations are near the wavelength range in 700nm and have absorbent as well as reflective wavelength ranges, there is a much difference in terms of its reflection rate. There are currently many researches on vegetation index being conducted in order to apply the remote-sensing technology to vegetations rising their characteristics of absorbent and reflective wavelength ranges. Normalized Difference Vegetation Index (NDVI) and Perpendicular Vegetation Index (PVI) have been most commonly used. It is usually the evaporation, carbon-dioxide consumption, and chlorophyll density that represent the activity of vegetation, but chlorophyll density is the most commonly used among them. Since the red wavelength range used to obtain the NDVI and PVI has a strong extinction of chlorophyll, it is also useful to test chlorophyll density. The NDVI, in particular, is used to identify the vegetation conditions summarily, and thus, is suitable for initiative researches. Nevertheless, since these vegetation index produce mixed information of the Vegetation vigor and vegetation cover, it is essential to monitor a wavelength range that is independent from redundancy of the Vegetation vigor and vegetation cover. Although many vegetation indices have evaluated both the vegetation vigor and Vegetation cover simultaneously, this research intends to emphasize the utility of separable evaluations of the Vegetation vigor and Vegetation Cover rate through an experiment with grasses. As a result of evaluating vegetation index using spectral reflectance, a separable evaluation of the vegetation vigor and cover has been found more useful.

• Journal of Bio-Environment Control
• /
• v.6 no.3
• /
• pp.168-175
• /
• 1997

In greenhouse, data on evapotranspiration or water consumption is important for the rational water management, irrigation planning, thermal environment analysis, and watering automation. But little investigations have been attempted to make clear the characteristics of water consumption in greenhouse. In this paper, evapotransplrations of lettuce and cucumber by cropping systems were investigated. And the correlations among evapotranspiration, pan evaporation, solar radiation, mean air temperature, and minimum relative humidity were analyzed. Experimental cropping systems of lettuce were soil culture and NFT system. Those of cucumber were soil culture, perlite culture, and rockwool culture. Total water consumption of lettuce was 2.62$\ell$/plant in soil culture and 1.71$\ell$/plant in NFT system. That of cucumber was 45.22$\ell$/plant in soil culture, 27.45$\ell$/plant in rockwool culture and 29.06$\ell$/plant in perlite culture. Therefore total water consumption of soil culture showed higher than soilless culture.

• International Journal of Highway Engineering
• /
• v.6 no.2 s.20
• /
• pp.15-24
• /
• 2004

Oxidation causes increment of the quantity of large molecular size or LMS in asphalt and is a major reason for hardening of asphalt binder. An extended service life of pavement on a road is expected by reducing oxidation of binder. Oxidation of binder occurs during hot mixing with aggregates before placement on road and then during in-service after the asphalt pavement is constructed. Quantitative increase of LMS as result of aging after RTFO and PAV was analyzed based on the data from high-pressure gel-permeation chromatography (HP-GPC). Polymer modified asphalt (PMA) after RTFO procedure showed 20-30% increment in LMS and then after PAV procedure more than twice, although the percentage of increment was different according to asphalt brand and grade. The PMAs containing LDPE or SBS, which showed a great mechanical property improvement in previous studies, were selected for characterizing PMA aging In this study. Considerably reduced increment of LMS was observed from the PMA containing LDPE after RTFO and PAV procedures. The GPC result showing the binder with less LMS increment means that the asphalt while being mixed with LDPE was aged less during the aging treatment. The dispersed particle of LDPE in asphalt cement seems to disturb oxidative aging reaction and evaporation.

• Progress in Medical Physics
• /
• v.14 no.3
• /
• pp.161-166
• /
• 2003

To evaluate the performance of cadmium sulfide as a multi-function X-ray dosimeter, we made an X-ray detector that was based on cadmium sulfide using evaporation technology, and measured its response to X-ray exposure. The voltages of cadmium sulfide were measured on the various X-ray tube potentials, X-ray tube currents and exposure times. The regression analysis of the voltage response of CdS on the tube-potential variation was y=0.0995x-0.1146 ($R^2$=0.9595, $\sigma$=0.08, standard error=2%) and the regression analysis of the voltage response of CdS on the tube-potential variation was y=0.0439x+1.1891 ($R^2$=0.9021, $\sigma$=0.04, standard error=1.8%) The regression analysis of the voltage response of CdS on the X-ray exposure time variation was y=8.2853+5.5878 ($R^2$=0.7287, $\sigma$=0.06, standard error=1.9%). In conclusion, cadmium sulfide responded linearly to the variation X-ray conditions, suggesting cadmium sulfide to be a feasible X-ray sensor of multi-function dosimeter related instruments.