• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.47 no.2
• /
• pp.47-55
• /
• 2010

The power line communication channel has characteristic variation problems which are caused by load. The spread spectrum technique has been used to overcome these problems. One of that is the direct sequence spread spectrum(DS/SS) system which is not necessary to additional hardwares. The BER of DS/SS system is decreased by longer length of PN code, but data transfer rate is decreases, so data transfer rate is hard to satisfies their own specifications especially in narrowband PLC systems. Spread Spectrum system with Dual-processing Gain tries to reflect cyclic characteristics of power line noise. But that system assumes that shapes of power line channel are symmetrical with respect to the 1/4 point of main frequency(60Hz in Korea), therefore cannot achieves various shapes of real power line noise. Thus in this paper, noise adaptive DS/SS system which PN code is changed by noise levels for various channel noises is proposed and simulated. The different kinds of noises are modeled and measured for simulation, the proposed system is verified that has lower data transfer rate and lower error rate than conventional system by simulation results.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.12
• /
• pp.56-63
• /
• 2012

The WBAN technology means a short distance wireless network which provides each device interactive communication by connecting devices inside and outside of body. Standardization on the physical layer, data link layer, network layer and application layer is in progress by IEEE 802.15.6 TG BAN. Wireless body area network is usually configured in energy efficient using sensor and zigbee device due to the power limitation and the characteristics of human body. Wireless sensor network consist of sensor field and sink node. Sensor field are composed a lot of sensor node and sink node collect sensing data. Wireless sensor network has capacity of the self constitution by protocol where placed in large area without fixed position. Mobile sink node distribute energy consumption therefore network life time was increased than fixed sink node. The energy efficient is important matter in wireless body area network because energy resource was limited on sensor node. In this paper we proposed cluster topology algorithm for efficient data transmission in wireless body area network based mobile sink. The proposed algorithm show good performance under the advantage of grid routing protocol and TDMA scheduling that minimized overlap area on cluster and reduced amount of data on cluster header in error prone wireless sensor network based on mobile sink.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.39 no.3
• /
• pp.18-31
• /
• 2002

In this study, we introduce a concept of advanced neurofuzzy polynomial networks(ANFPN), a hybrid modeling architecture combining neurofuzzy networks(NFN) and polynomial neural networks(PNN). These networks are highly nonlinear rule-based models. The development of the ANFPN dwells on the technologies of Computational Intelligence(Cl), namely fuzzy sets, neural networks and genetic algorithms. NFN contributes to the formation of the premise part of the rule-based structure of the ANFPN. The consequence part of the ANFPN is designed using PNN. At the premise part of the ANFPN, NFN uses both the simplified fuzzy inference and error back-propagation learning rule. The parameters of the membership functions, learning rates and momentum coefficients are adjusted with the use of genetic optimization. As the consequence structure of ANFPN, PNN is a flexible network architecture whose structure(topology) is developed through learning. In particular, the number of layers and nodes of the PNN are not fixed in advance but is generated in a dynamic way. In this study, we introduce two kinds of ANFPN architectures, namely the basic and the modified one. Here the basic and the modified architecture depend on the number of input variables and the order of polynomial in each layer of PNN structure. Owing to the specific features of two combined architectures, it is possible to consider the nonlinear characteristics of process system and to obtain the better output performance with superb predictive ability. The availability and feasibility of the ANFPN are discussed and illustrated with the aid of two representative numerical examples. The results show that the proposed ANFPN can produce the model with higher accuracy and predictive ability than any other method presented previously.

• Journal of Korean Ophthalmic Optics Society
• /
• v.21 no.3
• /
• pp.275-280
• /
• 2016

Purpose: This study is intended to look into the difference in surgery effects through the analysis of risk factors on how the common adult diseases among Korean adults diseases (glaucoma, hypertension and diabetes) are affecting cataract. Methods: Cataract surgery patients' daily records at hospitals in Jeonnam were used as analysis data. Factors - which can affect the results of medical treatment before and after an operation - were classified into the input, process and outcome of medical treatment. The medical treatment and patient characteristics were reflected as the input of medical treatment, and clinical results, functional status and general status as the process of medical treatment. Results: There was a close relationship between adult diseases of glaucoma, diabetes and hypertension, and cataract. Visual acuity of adult diseases patients was 10% lower than of non-adult diseases patients. And for post-surgery it was around 16% difference in refractive error and visual acuity between two groups. Conclusions: According to a study result, the cataract has been confirmed that there is a close relationship of Adult disease patients's glaucoma, diabetes and hypertension. Depending on the type about these adult diseases, before and after cataract surgery, vision and refractive power was found to indicate a significant difference when compared with conventional low normal adult control.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.35 no.5
• /
• pp.332-340
• /
• 2015

Acoustic emission (AE) is an effective nondestructive test that uses transient elastic wave generated by the rapid release of energy within a material to detect any further growth or expansion of existing defects. Over the past decades, because of environmental issues, the use of compressed natural gas (CNG) as an alternative fuel for vehicles is increasing because of environmental issues. For this reason, the importance and necessity of detecting defects on a CNG fuel tank has also come to the fore. The conventional AE method used for source location is highly affected by the wave speed on the structure, and this creates problems in inspecting a composite CNG fuel tank. Because the speed and dispersion characteristics of the wave are different according to direction of structure and laminated layers. In this study, both the conventional AE method and the energy based contour map method were used for source location. This new method based on pre-acquired D/B was used for overcoming the limitation of damage localization in a composite CNG fuel tank specimen which consists of a steel liner cylinder overwrapped by GFRP. From the experimental results, it is observed that the damage localization is determined with a small error at all tested points by using the energy based contour map method, while there were a number of mis-locations or large errors at many tested points by using the conventional AE method. Therefore, the energy based contour map method used in this work is more suitable technology for inspecting composite structures.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.2
• /
• pp.227-235
• /
• 2018

Along with the recent increase in traffic volume of vehicles, accidents involving rollover of vehicles have been rapidly increased, resulting in an increase casualties. And to prevent this, various technologies such as vehicle crash test equipment and analysis program development have been advanced. In this study, the applied vehicle model is FORD EXPLORER model, and PC-Crash program for vehicle collision analysis is used to predict the rollover accident behavior of SUV and the collision velocity. Compared with the actual rollover behavior of SUV through the FMVSS No 208 regulations, the analysis results showed similar results, the characteristics of the collision velocity and roll angle showed a tendency that the error rate slightly increased after 1000 msec. Then, as a result of considering using the database of NHTSA, it is shown that the rollover accident occur most frequently in the range of the collision velocity of 15~77 km/h and the collision angle of $22{\sim}74^{\circ}$. And it is possible to estimate the vehicle speed and collision time when the vehicle roof is broken by reconstructing the vehicle starting position, the roof failure position and the stop position by applying the actual accident case.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.3 s.333
• /
• pp.25-32
• /
• 2005

In this papers, we first, therefore, designed VCO(voltage controlled oscillator) that is composed of the dielectric resonator and the varactor diode, and then designed and fabricated PLDRO(phase locked dielectric resonator oscillator) that is combined with the sampling phase detector and loop filter. The measured results of the fabricated PLDRO at 12.05 [GHz] show the output power is 13.54 [dBm], frequency tuning range approximately +/- 7.5 [MHz], and Power variation over the tuning range less than 0.2 [dB], respectively. The phase noise which effects on bits error rate in digital communication is obtained with -114.5 [dBc/Hz] at 100 [KHz] offset from carrier, and The second harmonic suppression is less than -41.49 [dBc]. These measured results are found to be more improved than those of VCO without adopting PLL, and the phase noise and power variation performance characteristics show the better performances than those of conventional PLL.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.40 no.6
• /
• pp.20-30
• /
• 2003

In a conventional method based on quadrature 2D Gator wavelets to extract iris features, the iris recognition is performed by a 256-byte iris code, which is computed by applying the Gabor wavelets to a given area of the iris. However, there is a code redundancy because the iris code is generated by basis functions without considering the characteristics of the iris texture. Therefore, the size of the iris code is increased unnecessarily. In this paper, we propose a new feature extraction algorithm based on the ICA (Independent Component Analysis) for a compact iris code. We implemented the ICA to generate optimal basis functions which could represent iris signals efficiently. In practice the coefficients of the ICA expansions are used as feature vectors. Then iris feature vectors are encoded into the iris code for storing and comparing an individual's iris patterns. Additionally, we introduce two methods to enhance the recognition performance of the ICA. The first is to reorganize the ICA bases and the second is to use a different ICA bases set. Experimental results show that our proposed method has a similar EER (Equal Error Rate) as a conventional method based on the Gator wavelets, and the iris code size of our proposed methods is four times smaller than that of the Gabor wavelets.

• Journal of the Korea Society of Computer and Information
• /
• v.16 no.12
• /
• pp.83-92
• /
• 2011

Typographical errors by the author's mistyping occur frequently in a document being prepared with word processors contrary to usual publications. Preparing this online document, the most common orthographical errors are spelling errors resulting from incorrectly typing intent keys to near keys on keyboard. Typical spelling checkers detect and correct these errors by using morphological analyzer. In other words, the morphological analysis module of a speller tries to check well-formedness of input words, and then all words rejected by the analyzer are regarded as misspelled words. However, if morphological analyzer accepts even mistyped words, it treats them as correctly spelled words. In this paper, I propose a simple method capable of detecting and correcting errors that the previous methods can not detect. Proposed method is based on the characteristics that typographical errors are generally not repeated and so tend to have very low frequency. If words generated by operations of deletion, exchange, and transposition for each phoneme of a low frequency word are in the list of high frequency words, some of them are considered as correctly spelled words. Some heuristic rules are also presented to reduce the number of candidates. Proposed method is able to detect not syntactic errors but some semantic errors, and useful to scoring candidates.

• Journal of Korean Society on Water Environment
• /
• v.24 no.6
• /
• pp.718-724
• /
• 2008

The ion selective microelectrode (ISME) has been used for measuring the ion profile of DO, $NH_4{^+}-N$, $NO_2{^-}-N$ and $NO_3{^-}-N$ in biofilm. In this study we evaluated the detection limit and validity of ISME and applied ISME for the continuous measurement of $NH_4{^+}-N$ and $NO_3{^-}-N$ concentration in the modified Ludzack-Ettinger (MLE) process. Average detection limits of $NH_4{^+}-N$ and $NO_3{^-}-N$ ISME were $10^{-4.44}M$ and $10^{-4.62}M$, respectively. Since the ISME with $5{\sim}10{\mu}m$ of tip diameter showed a faster response time than that of $1{\sim}5{\mu}m$, the ISME with a tip diameter of $5{\sim}10{\mu}m$ was fabricated and used to make real-time ion detections. Direct monitoring of $NH_4{^+}-N$ and $NO_3{^-}-N$ concentrations in the aerobic (2) tank causes the instability of the electromotive force (EMF) for the initial 5~8 hours and also causes remarkable error values of $NH_4{^+}-N$ and $NO_3{^-}-N$ concentration. This phenomenon is caused by aeration and mixing in the reactor. Thus, the measuring chamber was newly designed for the aerobic (2) tank and then the EMF of the ISME were stabilized in less than 1 hour. Errors of $NH_4{^+}-N$ and $NO_3{^-}-N$ concentration were decreased after stabilization of the EMF. The ISME analysis were well corresponded to the results of auto analyzer and ion chromatography. Consequently, the concentration of $NH_4{^+}-N$ and $NO_3{^-}-N$ could be continuously measured for 178 hours by the ISME.