• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.5
• /
• pp.611-617
• /
• 2018

The application of health monitoring, including a fault detection technique, is needed to secure the structural safety of large structures. A 2-step crack identification method for detecting the crack location and size of the beam structure is presented. First, a crack occurrence region was estimated using the modified Laplacian operator for the strain mode shape obtained from the distributed local strain data. The crack location and size were then identified based on the natural frequencies obtained from the acceleration data and the neural network technique for the pre-estimated crack occurrence region. The natural frequencies of a cracked beam were calculated based on an equivalent bending stiffness induced by the energy method, and used to generate the training patterns of the neural network. An experimental study was carried out on an aluminum cantilever beam to verify the present method for crack identification. Cracks were produced on the beam, and free vibration tests were performed. A crack occurrence region was estimated using the modified Laplacian operator for the strain mode shape, and the crack location and size were assessed using the natural frequencies and neural network technique. The identified crack occurrence region agrees well with the exact one, and the accuracy of the estimation results for the crack location and size could be enhanced considerably for 3 damage cases. The presented method could be applied effectively to the structural health monitoring of large structures.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.2
• /
• pp.14-22
• /
• 2017

The frequency and scale of natural disasters due to the abnormal climate phenomena caused by global warming have being increasing all over the world. Various natural disasters, such as typhoons, earthquakes, floods, heavy rain, drought, sweltering heat, wind waves, tsunamis and so on, can cause damage to human life. Especially, the damage caused by natural disasters such as the Earthquake of Japan, hurricane Katrina in the United States, typhoon Maemi and so on, have been enormous. At this stage, it is difficult to estimate the scale of damage due to (future) natural disasters and cope with them. However, if we could predict the scale of damage at the disaster response level, the damage could be reduced by responding to them promptly. In the present study, therefore, among the many types of natural disaster, we developed a function to estimate the damage due to wind waves caused by sea winds and waves. We collected the damage records from the Disaster Report ('91~'14) published by the Ministry of Public Safety and Security about wind waves and typhoons in the western coastal zone and, in order to reflect the inflation rate, we converted the amount of damage each year into the equivalent amount in 2014. Finally, the meteorological data, such as the wave height, wind speed, tide level, wave direction, wave period and so on, were collected from the KMA (Korea Meteorological Administration) and KHOA (Korea Hydrographic and Oceanographic Agency)'s web sites, for the periods when wind wave and typhoon damage occurred. After that, the function used to estimate the wind wave damage was developed by reflecting the regional characteristics for the 9 areas of the western coastal zone.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.3
• /
• pp.2100-2108
• /
• 2015

This study was conducted to examine the effects of a simulation-based learning scenario using standardized respiratory patients regarding emergency care on learning satisfaction, and self efficacy, clinical skill competency of health related department students. A quasi-experimental non-equivalent control group pre-post test design was used. A total of 50 students, 25 students for the experimental group and 25 students for the control group, The experimental group received the 2 educations sessions and 1 evaluation session with 180 minutes for each session. It was implemented in November, 2013. Data were analysed using frequency, ratio and t-test by the SPSS/Win 18.0. The experimental group who had the simulation-based learning scenario using standardized respiratory patients showed significantly higher learning satisfaction and self efficacy, clinical skill competency compared with the control group who had a traditional simulation education. Through this study, simulation-based learning scenario using standardized patients was verified to be an effective teaching method to be grow up on professional competency of health related department students. Also the simulation-based learning scenario using standardized patients should be developed in the various fields.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.5
• /
• pp.412-419
• /
• 2017

Purpose:This study was conducted to identify the effects of theSemi-Fowler's position on post-operative recovery and pain for patients with laparoscopic abdominal surgery Methods: This study utilized a non-equivalent control group non-synchronized design to validate the effects of theSemi-Fowler's position. After IRB approval, 56 patients took part in this study, 29 in the experimental group and 27 in the control group. Consent was obtained from the participants. The Semi-Folwer's position was applied to experimental group and the supine position was applied to the control group for 24 hours after surgery. All data were reviewed retrospectively from April to June 2016. Collected data, frequency, percentage, average, standard deviation, chi-squared test, independent t-test and repeated measures ANOVA were conducted using SPSS 20.0. Results: There was no significant difference between the experimental and control group with regard to recovery outcomes; however, there was a significance differencebetween groups and among check times with regard to post operational pain. Conclusion:The results of this study provide information that will be usefulto the development of strategies for improving recovery outcomes and pain for laparoscopic operation patients.

• Geophysics and Geophysical Exploration
• /
• v.2 no.2
• /
• pp.96-103
• /
• 1999

Most of saline water inousions have been diagnosed by geophysical or geochemical approach independently. The objective of this study is to provide the effective method to detect the saline water intrusion on the ground water in the vicinity of seashore using these two methods. Schulumberger sounding, frequency domain electromagnetic sounding and geochemical analysis of ground water were carried out to explore saline water intrusion. Schulumberger sounding was implemented in dry surface condition before irrigation water was introduced into the field, while electromagnetic sounding was carried out in wet ground condition after the irrigation. The purpose of duplicated measurements on the equivalent spot at different times was to investigate the variation of anomaly zone depending on the amount of ground water. It was possible to discriminate the anomalous zone due to high water saturation from the low electric resistivity zone by high salt concentrations through this way. For the verification of the geophysical result, the ground water samples in the study area were collected and analysed at the 23 points near the measuring spots. The groundwater at the spot nearest to the sea water intrusion identified by geophysical method indicates higher salinity than the standard limit concentration for agricultural irrigation water (250 mg/1). Isotope analysis of $D({^2}H)$ vs. is ${^18}O$ and PCA analysis were used to discriminate the anthropogenic pollution from those of high salinity from sea water intrusion.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.2
• /
• pp.5-12
• /
• 2000

Uncooled metallic thin-film thermopile infrared detectors have been fabricated, and the figures of merit for the detectors were examined. The hot junctions of a thermopile were prepared on a $Si_{3}N_{4}/SiO_{2}/Si_{3}N_{4}$-membrane which acts as a thermal isolation layer, the cold junctions on the membrane supported with the silicon rim which functions as a heat sink, and Au-black was used as an infrared absorber. Infrared absorbance of Au-black, which strongly depends on the chamber pressure during Au-evaporation and its mass per area, was found to be about 90 ％ in the wavelength range from 3${\mu}{\textrm}{m}$ to 14${\mu}{\textrm}{m}$. Voltage responsivity, noise equivalent power, and specific detectivity of Bi-Sb thermopile infrared detector at 5 Hz-chopping frequency were about 10.5V/W, 2.3 nW/Hz$^{1/2}$, 및 $1.9\times10^{7}$ cm.Hz$^{1/2}$/w at room temperature in air, respectively.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.10
• /
• pp.80-86
• /
• 2014

A low-noise readout circuit is studied for 2-D capacitive microbolometer focal plane arrays (FPAs). In spite of the merits of the integration method, a simple and effective pixelwise readout circuit without integration is used for input circuit because of a small pixel size and narrow noise bandwidth. To reduce the power consumption and the kT/C noise, which is the dominant noise of the capacitive microbolometer FPAs with small capacitance, a new correlated double sampling (CDS) is used for columnwise circuit. The proposed circuit has been designed using a $0.35-{\mu}m$ 2-poly 4-metal CMOS process for a microbolometer array with a pixel size of $50{\mu}m{\times}50{\mu}m$. The proposed circuit effectively reduces the kT/C noise and the other low-frequency noise of microbolometer, and the noise characteristics of the fabricated chip have been verified by measurements. The rms noise voltage of the proposed circuit is reduced from 30 % to 55 % compared to that of the simple readout input circuit, and the noise equivalent temperature difference (NETD) of the proposed circuit is very low value of 21.5 mK.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.11
• /
• pp.1078-1091
• /
• 2011

In this paper, a triple band-notched UWB antennas using a spiral resonator and a complementary split ring resonator is proposed as two types. The band-rejection characteristic of the designed antenna is analyzed through the structure and equivalent circuit model of spiral resonator and CSRR. The measured results of first type antenna show that a VSWR less than 2 was satisfied with a resonant frequency in the range of 1.16~12 GHz and it can be obtained the band-stop performance at 3.3~3.85 GHz, 5.15~6.1 GHz, and 8.025~8.5 GHz. The measured results of second type antenna show that a VSWR less than 2 was satisfied with this antenna works from 1.79 to 12 GHz and it can be achieved the band-notched performance at 3.3~3.88 GHz, 5.12~5.94 GHz, and 8.025~8.51 GHz. Through the measured results, the designed antenna was satisfied UWB band except for triple notched bands.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.26 no.5
• /
• pp.518-527
• /
• 2016

The present study considers the usage of concentrated forces to simulate real panel flutter. The concept of using concentrated forces have been validated for studying the flutter of wing structure in subsonic flow, yet its application in the supersonic region remained to be explored. Hence, a simply supported panel subjected to forces, equivalent to aerodynamic force is considered for studying supersonic panel flutter. The distributed aerodynamic forces are approximated to few concentrated forces by taking numerical integration. The aeroelastic equation is formulated using the classical small-deflection theory and the piston theory for linear panel flutter whereas for emulated panel flutter the flutter equation is derived by replacing the pressure due to aerodynamic loading with pressure from concentrated loading. Finally, flutter frequency, flutter dynamic pressure, and corresponding mode shape are found for emulated panel flutter and compared with linear panel flutter. Two important parameters, the number of concentrated forces and their location are discussed through numerical examples and optimization process respectively. So far, the flutter results acquired in this study are reasonable to suggest the feasibility of reproducing panel flutter using concentrated forces.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.11
• /
• pp.1128-1134
• /
• 2014

In this paper, the effects of a metamaterial slab with negative permeability in a magnetically coupled wireless power transfer system (WPT) in the overall performance are analyzed quantitatively in terms of the effective quality factors of the loop resonators and coupling coefficient considering the slab losses, based on an equivalent circuit. Using the ideal metamaterial slab(lossless slab), the WPT efficiency is improved considerably by the magnetic flux focusing. However, the practical lossy slab made of RRs or SRRs limits the significant enhancement of WPT efficiency due to the relatively high losses in the slab consisting of RRs or SRRs near the resonant frequency. For the practical loop resonator, other than a point magnetic charge, using the practical lossy metamaterial slab in order to improve the transfer efficiency, the width of the slab needs to be optimized somewhat less than the half of the distance between two loop resonators. For the low-loss slab with its loss tangent of 0.001, the WPT efficiency is maximized at 93 % when the ratio of the slab width and the distance between the two resonators is approximately 0.35, compared with 53 % for the case without the slab. The efficiency in case of employing the high-low slab(loss tangent: 0.2) is maximized at 61 % when the slab ratio is 0.25.