• Applied Chemistry for Engineering
• /
• v.28 no.5
• /
• pp.501-505
• /
• 2017

Due to the rapid urbanization and increased population, there is an increase in airtight nature of buildings which causes serious indoor air pollution. Among several indoor air pollutants, volatile organic compounds (VOCs) emitted from paint are of major concern. Therefore, there is an urge for the development of environmental friendly paint products. In this wok, a natural wall paint (NWP) was prepared by utilizing a natural clay material "sericite" as a main component. A small chamber test was carried out to identify the toxic substances release from NWP and the results were compared with two eco-friendly commercial paints. The total VOCs were detected in trace level inside the test chamber and their concentrations were below the recommended indoor air quality standards. Toluene was not detected for NWP, whereas formaldehyde was observed in trace level. The toxicity index results were compared with two commercial paints and found that NWP exhibited less harmful gas emission. Based on certification rating of building materials, NWP can be classified as the first grade of building materials. Due to the above advantages, the use of sericite as a major component in NWP will be a useful technique to maintain the indoor air quality.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.6D
• /
• pp.533-538
• /
• 2012

The purpose of weighting traffic management strategies is to reach strategic goal through intended and balanced implementations. The AHP is commonly used technique to derive perspective and strategic goals, and to give priorities to them in a organization. In this study, perspective and strategic goals are derived through surveys and interviews with staffs of a traffic management agency. And then, priority of perspective and strategic goals is performed through the AHP. In this study, three things were identified. Firstly, it was found weighting perspectives such as values for customers, future, activity, and performances were in sequence performed. The value for customers were ranked the first. Secondly, it was found increasing of customer- centric thinking and values of eco- friendly system are the highest weighting in strategic goal. Third, it was found increasing of customer-centric thinking is the most important in headquarters and regional headquarter. But, Values of eco-friendly system is ranked as the most important in opinion of branch office's staffs. It was also identified that depending on the working places, such as headquater and branch offices, the response differs.

• Clean Technology
• /
• v.17 no.1
• /
• pp.25-30
• /
• 2011

This study presents a fabrication method of cell-chip using aqueous solution based surface modification. The applications of cell-chip have potential for fundamental study of genetics, cell biology as well as cancer diagnostics and treatment. Conventional methods for fabrication of cell-chip have been limited in economic loss and environmental pollution because of the use of harsh organic solvent, complex process of silicon technology, and expensive equipment. In order to fabricate cell chip, we have proposed simple and eco-friendly process combined polyelectrolyte multilayer coating with microcontact printing. For the proof of concept, the cell chip can be applied to analyze the different expression of cell surface glycans and derivatives between cancer and normal cells. Our proposed method is useful technique for the application of novel cancer diagnostics and basic medical engineering.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.17 no.2
• /
• pp.1-14
• /
• 2014

The purpose of this study is to identify the efficiency of LID technologies for controlling non-point source pollution from urban areas. The recent technical responses to managing water resource and urban areas according to the influence of climate change is an important national policy, along with green growth. Through various reference studies reasonable ways to consider a wholistic plan on urban-eco-friendly river management, the Low Impact Development (LID) as the adequate river management method is being undertaken in foreign countries to technically apply to urban plans. However, the LID is at the initial stage in Korea, with no specific studies implemented. Thus, this study explored whether LID technologies can be efficient measures to control non-point source pollution on the cost side. Ulsan's Namgu and Bukgu have been chosen as case studies that illustrate the efficiency of the LID technologies. On investigation, if LID technologies are designed properly, the efficiency of them is expected to higher than that of sewage treatment plant.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2003.03a
• /
• pp.493-498
• /
• 2003

In case of slope failure by planted protection is constructed on the slope according to of the choice trend of a recently environmental-friendly countermeasure, there has a limitation about diagnosis and preparation of measure. Also, collapse of tunnel pithead department slope has maximum in construction and countermeasure method of construction choice unlike cut-slope. In this study, analyzed inside circumstance of slope using geophysical exploration for stability analysis and countermeasure inside presentation of tunnel pithead department slope which collapse happens. geophysical exploration used dipole(Dipole-Dipole) method that is based to distribution principle does specific resistance, goes side by side with on-the-spot observation and draws base strength parameter and executed stability analysis, and presented stabilization countermeasure inside of collapse slope on this. I wish to conduce in development and research for use technical development of geophysical exploration technique hereafter by executing geophysical exploration in road collapse spot applying through this study.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.4
• /
• pp.8-15
• /
• 2013

Recently many kinds of electric vehicles have been developed as many governments demand the environmental friendly vehicles. In this paper, study of load optimization for the electric vehicle which has multiple axle power system was conducted. For the analysis of the vehicle which has three or four driving axles, a method based on the geometry and assumptions that considering axles as a spring model and normal forces of the axles are proportional to the displacement of the axles was applied with basic vehicle dynamics. With the developed vehicle analysis technique, algorithm to find the optimal motor operating points was developed. Using this algorithm, it was possible to find the optimization of vehicle load distribution for multiple axles according to the driving cycles. Also, control logic for the vehicle can be developed based on the optimization simulation results.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 1998.10a
• /
• pp.490-499
• /
• 1998

This study was initiated to investigate the applicability of sludge from water or waste water treatment on the crop cultivation. Sludge is generated in the process of water and wastewater treatment process in large quantity. The sludge can cause many environmental problems. we have a many available treatment methods of sludge However, these methods still shortcomings and are not. The composition of typical municipal sludge contains organics and inorganics. The organics components are normally burnt in high temperature and mainly inorganics components are left after thermal treatment process. For the production of artificial media, chabazite was used as additive, and the mixed material was thermally treated in the firing kiln at 800~1,10$0^{\circ}C$ for about 10 minutes. The physical and chemical characteristics of artificial media were analyzed and it showed that the artificial media could be used as a media for plants and soil conditioner for farmland. The concentrations of the toxic heavy metals in the media were lower then those in the soil quality standard for farmland. This study illustrated that the artificial media production process, and introduced how to produce it's possible application as a media for Plant growth.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.03a
• /
• pp.571-578
• /
• 2009

Recently, micropiling techniques are increasingly applied in foundation rehabilitation/underpinning and seismic retrofitting projects where working space provides the limited access for conventional piling methods. Micropiling techniques provide environmental-friendly methods for minimizing disturbance to adjacent structures, ground, and the environment. Its installation is possible in restrictive area and general ground conditions. The cardinal features that the installation procedures cause minimal vibration and noise and require very low ceiling height make the micropiling methods to be commonly used for underpin existing structures. In the design point of view, the current practice obligates the bearing capacity of micropile to be obtained from skin friction of only rock-socketing area, in which it implies the frictional resistance of upper soil layer is ignored in the design process. In this paper, a new micropiling method and its verification studies via field installation are presented. The new method provides a specific way to grout bore-hole to increase frictional resistance between surrounding soil and pile-structure and it allows to consider the skin friction of micropiles for upper soil layer during design process.

• Composites Research
• /
• v.34 no.6
• /
• pp.345-349
• /
• 2021

The continued environmental pollution caused by fossil fuel consumption has prompted researchers around the world to develop environmentally friendly energy technologies. Electrochemical energy storage is the significant area of research in this development process, and the research significance of supercapacitors in this field is increasing. Herein, a simple electrodeposition synthetic route was explored to develop the MoP layered cathode material. The layered structure provided a highly ion-accessible surface for smooth and faster ion adsorption/desorption. After Fe was doped into MoP, the morphology of MoP changes and the electrochemical performance was significantly improved. Specific capacitance value of the binder-free FeMoP electrode was found to be 269 F g^-1 at 2 A g^-1 current density in 6 M aqueous KOH electrolyte. After adding Fe to MoP, an additional redox contribution was observed in the redox conversion from Fe³⁺ to Fe²⁺ redox pair, and the charge transfer kinetics of MoP was effectively improved. This research can provide guidance for the development of supercapacitor electrode materials through simple electrodeposition technology.

• Journal of the Korean institute of surface engineering
• /
• v.34 no.6
• /
• pp.553-567
• /
• 2001

Electrodeposition technology is widely used in industry for various kinds of coatings. Modifications in this technology led to several processes to meet various requirements. Electrolysis in ionic liquids has many advantages such as low energy consumption of energy, low pollutant emission and low operating costs. Although ionic liquids have already been used in liquid/liquid extraction processes, only recently their use in electrodeposition was exploited. Electrochemical deposition of composites is an expanding area. Coupled with the progress in the synthesis of nanometric powder, this research will open a large number of innovative materials. Pulse current plating is another electrodeposition technique which yields improved coatings. Although electrodeposition is now regarded as an environmental non-friendly process, it is economically viable and has many inherent advantages. For certain applications, alternatives to electrodeposition have not yet been fully implemented. Hence, continued research in this technology is warranted. This article reviews some recent advances in electrodeposition technology. Aspects of electrodeposition such as electrolysis in ionic liquids, electrodeposition of composites, pulse current plating techniques, metal and alloy deposition, compound deposition and effects of additives are discussed in this review.