• Journal of the Korean Geotechnical Society
• /
• v.38 no.7
• /
• pp.49-62
• /
• 2022

The hollow modular concrete block reinforced foundation method is one of the ground reinforcement foundation methods that uses hexagonal honeycomb-shaped concrete blocks with mixed crushed rock to reinforce soft grounds. It then forms an artificial layered ground that increases bearing capacity and reduces settlement. The hollow modular honeycomb-shaped concrete block is a geometrically economical, stable structure that distributes forces in a balanced way. However, the behavioral characteristics of hollow modular concrete block reinforced foundations are not yet fully understood. In this study, a bearing capacity test is performed to analyze the reinforcement effectiveness of the hollow modular concrete block through the laboratory model tests. From the load-settlement curve, punching shear failure occurs under the unfilled sand condition (A-1-N). However, the filled sand condition (A-1-F) shows a linear curve without yielding, confirming the reinforcement effect is three times higher than that of unreinforced ground. The bearing capacity equation is proposed for the parts that have contact pressure under concrete, vertical stress of hollow blocks, and the inner skin friction force from horizontal stress by confining effect based on the schematic diagram of confining effect inside a hollow modular concrete block. As a result of calculating the bearing capacity, the percentage of load distribution for contact force on the area of concrete is about 65%, vertical force on the area of hollow is 16.5% and inner skin friction force of area of the inner wall is about 18.5%. When the surcharge load is applied to the concrete part, the vertical stress occurs on the area of the hollow part by confining effect first. Then, in the filled sand in the hollow where the horizontal direction is constrained, the inner skin friction force occurs by the horizontal stress on the inner wall of the hollow modular concrete block. The inner skin friction force suppresses the punching of the concrete part and reduces contact pressure.

• Korean Journal of Heritage: History & Science
• /
• v.55 no.4
• /
• pp.180-193
• /
• 2022

The East Nine Royal Tombs is a representative place in the Royal Tombs of Joseon (a World Heritage Site). It consists of 1,289 stone artifacts including 979 related stone structures, 310 stone statues, and objects. Most of the stone structures in the East Nine Royal Tombs are composed of biotite granite, but some tombs are composed of light red granite. As a result of magnetic susceptibility measurement, the average data from Geonwolleung to Mongneung, excluding Hyeolleung, were similar, so it is estimated that stones were obtained from the same quarry. In the case of Sungneung, Sureung, and Gyeongneung, the range of susceptibility measurement is widely distributed. It assumed that the newly produced stones were mixed in the moving and construction process. Also, stones might be gathered from different quarries. As a result of a conservation status investigation, both the mound member and the ridge stone had the highest damage rate due to peeling and granular decomposition according to surface weathering. In the case of surface discoloration, yellowing and soils were found in the burial mound members. Yellowing, blackening, and soil were identified in the ridge stone structures. Bio-degradation is the major factor of deterioration of the East Nine Royal Tombs and the conservation status of the tombs were detected as grades 4 to 5. It seems that it is easy for the environment of the royal tombs to form soil for the microorganisms and fine conditions for continuous moisture. In the case of structures, they are in relatively good condition. As a result of a comprehensive damage rating for each tomb, the overall condition is good, but the Geonwolleung Royal Tomb and Hyeolleung Tomb, which were created in the early period, had relatively high weathering ratings. Stone objects in East Nine Royal Tombs have lost many pieces and gateway members due to surface deterioration. Also, secondary damage is ongoing. Each damage factor of the stone artifacts of the East Nine Royal Tombs combines to cause various and continuous damages. Therefore, it is necessary to establish regular conservation status data of the stone artifacts for efficient management after processing as well as conservation treatment of the royal tombs, and specific management manuals and systems. This study investigated the conservation status of stone structures in the East Nine Royal Tombs, a World Heritage Site, and systematically classified them to provide priority and necessity for conservation processing. We look forward to establishing a plan for the conservation and management of the East Nine Royal Tombs with this database in the future.

• 한국노년학
• /
• v.27 no.2
• /
• pp.459-472
• /
• 2007

This research has its purpose of developing a tool to assess the needs of the Korean elderly at home population and to provide adequate services by evaluating their physical, psychological, and socio-environmental aspects. This developed tool is composed of two hundred questions and has the advantage of combined physical, psychological and social environmental situation assessment of the elderly at home. The tool also contains not only the objective view of the professionals, but also the subjective appeals of the elderly at home population so that it can reflect their substantial desires. The assessment tool was developed over 21 months from July, 2004 to March, 2006 and this period can be divided into three different stages. In the first stage, collecting of questions for the desire-focused assessment of the elderly by literature investigation and researching foreign source materials was carried out, and this ultimately developed assessment tool was applied to the long-term care insurance pilot project in the second stage. In this process, we revised some insufficiencies of this tool after we applied to elderly of 250 from the pilot project and other 200 elderly from this research team. For the last stage, the tool was completed by using inquiries of the focused group and the group of professionals to ensure its reliability and validity. In the process of developing the tool, the total of 200 questions under 13 subcategories was selected. The 13 subcategories are basic information, subjective appeals, information of the main helper, use of services, house environment, condition of health, condition of rehabilitation, daily living(ADL, IADL, defecation, assistance), social maintenance, behavioral disability, medical health, living habits, and strength. This tool is on the purpose to assess thoroughly the desires that the elderly at home population has and to provide the best service they need.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.14 no.3
• /
• pp.134-144
• /
• 2009

Paleoproductivity changes in the central part of the Bering Sea since the last glacial period were reconstructed by analyzing opal and total organic carbon (TOC) content and their mass accumulation rate (MAR) in sediment core PC23A. Ages of the sediment were determined by both AMS $^{14}C$ dates using planktonic foraminifera and Last Appearance Datum of radiolaria (L. nipponica sakaii). The core-bottom age was calculated to reach back to 61,000 yr BP. and some of core-top was missing. Opal and TOC contents during the last glacial period varied in a range of 1-10% and 0.2-1.0%, and their average values are 5% and 0.7%, respectively. In contrast, during the last deglaciation, opal and TOC contents varied from 5 to 22% and from 0.8 to 1.2%, respectively, with increasing average values of 8% and 1.0%. Opal and TOC MAR were low ($1gcm^{-2}kyr^{-1}$, $0.2gcm^{-2}kyr^{-1}$) during the last glacial period, but they increased (>5 and >$1gcm^{-2}kyr^{-1}$) during the last deglaciation. High diatom productivity during the last deglaciation was most likely attributed to the elevated nutrient supply to the sea surface resulting from increased melt water input from the nearby land and enhanced Alaskan Stream injection from the south under the restricted sea-ice and warm condition during the rising sea level. On the contrary, low productivity during the last glacial period was mainly due to decreased Alaskan Stream injection during the low sea-level condition as well as to extensive development of sea ice under low-temperature seawater and cold environment.

• Journal of Soil and Groundwater Environment
• /
• v.14 no.2
• /
• pp.33-44
• /
• 2009

The objective of the study was to develop a hybrid technology integrating biological and physicochemical technologies to efficiently remediate arsenic contaminated lands such as abandoned mine area. The tailing soil samples contaminated with As at a high level were obtained from Songchon abandoned mine, and the content of arsenic and heavy metals as well as physicochemical properties and mineral composition were investigated. In addition, two sets of sequential extraction methods were applied to analyze chemical speciations of arsenic and heavy metals to expect their leachability and mobility in geoenvironment. Based on these geochemical data of arsenic and heavy metal contaminants, column-type experiments on the bioleaching of arsenic were undertaken. Subsequently, experiments on the hybrid process incorporating bioleaching and electrokinetics were accomplished and its removal efficiency of arsenic was compared with that of the individual electrokinetic process. With the results, finally, the feasibilty of the hybrid technnology was evaluated. The arsenic removal efficiencies of the individual electrokinetic process (44 days) and the hybrid process incorporating bioleaching (28 days) and electrokinetics (16 dyas) were measured 57.8% and 64.5%, respectively, when both two processes were operated in an identical condition. On the contrary, the arsenic removal efficiency during the bioleaching process (28 days) appeared relatively lower (11.8%), and the result indicates that the bioleaching process enhanced the efficacy of the electrokinetic process as a result of mobilization of arsenic rather than removed arsenic by itself. In particular, the arsenic removal rate of the electrokinetics integrated with bioleaching was observed over than 2 times larger than that obtained by the electrokinetics alone. From the results of the study, if the bioleaching which is considered a relatively economic process is applied sufficiently prior to electrokinetics, the removal efficiency and rate of arsenic can be significantly improved. Consequently, the study proves the feasibility of the hybrid process integrating both technologies.

• Journal of Bio-Environment Control
• /
• v.21 no.3
• /
• pp.228-235
• /
• 2012

This study was carried out to investigate the effect of irrigation methods for reducing a drainage on the growth and yield in rockwool (Grodan co.) and cocopeat (chip : dust = 50 : 50 included fiber) culture. The nutrient solution was irrigated by $100J{\cdot}cm^{-2}$-100 mL, $50J{\cdot}cm^{-2}$-45 mL, $50J{\cdot}cm^{-2}$-40 mL, $50J{\cdot}cm^{-2}$-35 mL ($100{\sim}50J{\cdot}cm^{-2}$-100~35 mL, Nutrient solution 100~35 mL was irrigated per plant when the accumulated radiation was $100{\sim}50J{\cdot}cm^{-2}$). The drain rates per plant of 100-100, 50-45, 50-40, 50-35 were 26.3%, 8.8%, 6% 4.4% and 23.1%, 7.5%, 5% 3.4% in rockwool and cocopeat slabs. The water contents and EC of 100-100 and 50-45 were managed by the 55~70%, $3.0{\sim}5.0dS{\cdot}m^{-1}$ which were good condition for paprika culture in rockwool and cocopeat slabs, while those of 50-40 and 50-35 were managed by beyond 50%, $4.5{\sim}9.5dS{\cdot}m^{-1}$. The plant height, number of branches and leaf size of 100-100 and 50-45 were similarly increased while those of 50-40 and 50-35 were decreased. The fruit size and weight of 50-40 and 50-35 were small and light, while those of 100-100 and 50-45 were similarly big and heavy. The marketable fruits of 100-100 and 50-45 treatments were similarly more by 9.7~9.8 in rockwool and 8.8~8.9 in cocopeat, while the unmarketable fruits, the small and blossom end rot fruits were increased in 50-40 and 50-35 treatments. The yield of 100-100 and 50-45 treatments were similarly high.

• Journal of Bio-Environment Control
• /
• v.21 no.3
• /
• pp.261-266
• /
• 2012

This study was carried out in order to investigate the effect of MA packaging material on quality and shelf life of ferulae mushroom (Pleurotus ferulae) at 1, 8, and $24^{\circ}C$ storage temperatures. We found that the fresh weight loss was less than 1.5% in all temperatures (1, 8, and $24^{\circ}C$) and non-perforated breathable films (1,300 cc, 3,000 cc, 5,000 cc, 7,000 cc, 10,000 cc, 15,000 cc, 20,000 cc, and $40,000cc/m^2{\cdot}day{\cdot}atm$ oxygen transmission rate) treatments. The proper MA packaging material of ferulae mushroom was 1,300 cc and 3,000 cc films at $1^{\circ}C$ storage. Because 1,300 cc and 3,000 cc films showed proper level, 15% carbon dioxide and 5% oxygen concentration for MA storage, although the shelf life was higher in 1,300 cc (42 days) than 3,000 cc (38 days), and the ethylene concentration as well as off-order showed lower in 3,000 cc than 1,300 cc film. The 3,000 cc film was the most suitable for ferulae mushroom storage at $8^{\circ}C$, because atmosphere composition in package was not statistically significantly different among the film treatments. In addition, 3,000 cc film showed the second low ethylene concentration and the longest shelf-life of 19 days. The ferulae mushroom stored at $25^{\circ}C$ showed a vigorous respiration and resulted in an extreme CA condition in package at $5^{th}$ day after storage, and showed the highest visual quality in 1,300 cc film. As the shelf life of ferulae mushroom at $1^{\circ}C$ and $8^{\circ}C$ storage were 8 times and 4 times longer than at $25^{\circ}C$ storage respectively, so the ferulae mushroom should be stored and distributed in cold chain system.

• Korean Journal of Environment and Ecology
• /
• v.27 no.3
• /
• pp.316-326
• /
• 2013

This study has researched the national expansion, dispersion of nutria and investigated its inhabitation status for the past 3 years. The report has shown that the number of nutria habitat, reported to be distributed in 9 cities or districts in 2010, has been increased to 13 in 2012. In the research of 629 nutria habitats, 95.9% of habitat traces were found in Busan-Kyungnam area. From the research of relative density by location type for the 6 survey areas in these 5 areas above, it was shown 3.98(${\pm}2.56$)ind./100m in 2010, 2.90(${\pm}2.69$)ind./100m in 2011 and 1.39(${\pm}0.66$)ind./100m in 2012. From the research of relative density by habitat types, it was shown 3.48(${\pm}2.15$)ind./100m in palustrine wetland area, $1.01{\pm}(0.25)ind.$/100m in river area and $3.69{\pm}(2.83)ind.$/100m in riverine wetland area. It was shown that the annual average density in the areas has slightly been decreased for the past 3 years between 2010 and 2012. It also reported that the habitat density in the river area is a bit lower than that in the wetland area. Currently it can be determined that the nutria has fully adapted themselves to the various local environments of wetland, river, stream, and so on in Korea and the Relative density could be remarkably increased especially in the favorable condition like a wetland. As the ones living in the area with over-density could be spread out to other areas, the efficient management plan to control should be prepared considering ecological conditions.

• Economic and Environmental Geology
• /
• v.47 no.4
• /
• pp.335-349
• /
• 2014

The Pocheon skarn deposit, located at the northwestern part of the Precambrian Gyeonggi massif in South Korea, occurs at the contact between the Cretaceous Myeongseongsan granite and the Precambrian carbonate rocks, and is also controlled by N-S-trending shear zone. The skarn distribution and mineralogy reflects both structural and lithological controls. Three types of skarn formations based on mineral assemblages in the Pocheon skarn exist; a sodiccalcic skarn and a magnesian skarn mainly developed in the dolostone, and a calcic skarn developed in the limestone. Iron mineralization occurs in the sodic-calcic and magnesian skarn zone, locally superimposed by copper mineralization during retrograde skarn stage. The sodic-calcic skarn is composed of acmite, diopside, albite, garnet, magnetite, maghemite, anhydrite, apatite, and sphene. Retrograde alteration consists of tremolite, phlogopite, epidote, sericite, gypum, chlorite, quartz, calcite, and sulfides. Magnesian skarn mainly consists of diopside and forsterite. Pyroxene and olivine are mainly altered to tremolite, with minor phlogopite, talc, and serpentine. The calcic skarn during prograde stage mainly consists of garnet, pyroxene and wollastonite. Retrograde alteration consists of epidote, vesuvianite, amphibole, biotite, magnetite, chlorite, quartz, calcite, and sulfides. Microprobe analyses indicate that the majority of the Pocheon skarn minerals are enriched by Na-Mg composition and have high $Fe^{3+}/Fe^{2+}$, $Mg^{2+}/Fe^{2+}$, and $Al^{3+}/Fe^{2+}$ ratios. Clinopyroxene is acmitic and diopsidic composition, whereas garnet is relatively grossular-rich. Amphiboles are largely of tremolite, pargasite, and magnesian hastingsite composition. The prograde anhydrous skarn assemblages formed at about $400^{\circ}{\sim}500^{\circ}C$ in a highly oxidized environment ($fO_2=10^{-23}{\sim}10^{-26}$) under a condition of about 0.5 kbar pressure and $X(CO_2)=0.10$. With increasing fluid/rock interaction during retrograde skarn, epidote, amphibole, sulfides and calcite formed as temperature decreased to approximately $250^{\circ}{\sim}400^{\circ}C$ at $X(CO_2)=0.10$.

• Korean Journal of Environment and Ecology
• /
• v.28 no.3
• /
• pp.326-330
• /
• 2014

Flowering characteristics and acorn production of Quercus acuta were studied in a Quercus acuta forest at Wando island, Korea. Three sample trees were cut and measured to investigate flowering characteristics during flowering season. Eight $20m{\times}25m$ quadrats were set up and three $1m{\times}1m$ seed traps were established within each quadrat to investigate acorn production. There were no significant differences in number of female and male inflorescence per bearing shoot among crown positions, but these values decreased from the upper part to the lower part of crown. The number of female flowers was 5,025 flowers/tree, and of the total number, 60.3% was in the upper part, 28.4% was in the middle part and 11.3% was in the lower part of crown. The number of male flowers was 7,063 flowers/tree and increased from the lower part to the upper part of crown. Acorn production of total 24 seed traps was 947 acorns/$24m^2$, and of total acorn production, 11.0% was sound, 61.9% was damaged, 25.1% was decayed and 2.0% was empty. Monthly acorn production was 240 acorns/$24m^2$ in August, 632 acorns/$24m^2$ in September, 56 acorns/$24m^2$ in October, 17 acorns/$24m^2$ in November and 2 acorns/$24m^2$ in December. Acorns fallen in October showed higher mean length, diameter and weight than those of other months.