• Journal of the Korean Society for Marine Environment & Energy
• /
• v.12 no.2
• /
• pp.91-95
• /
• 2009

To understand the effect of attachment substrate on the growth of benthic microalgae, we experimentally investigated the growth of benthic microalgae Nitzschia sp. (Jinhae Bay strain) with additions of glass beads in different sizes. The glass beads used in this study are 0.09-0.15 mm (G1), 0.25-0.50 mm (G2), 0.75-1.00 mm (G3) and 1.25-1.65 mm (G4). No addition of glass beads used as controls. Highest specific growth rate (0.37/day) and maximum cell density ($9,232{\pm}840$ cells/mL) of Nitzschia sp. showed at the smallest glass beads (G1), and the specific growth rate and maximum cell density were decreasing with increasing size of glass beads (specific growth rate and maximum cell density of G4 was 0.24/day and $6,397{\pm}524$ cells/mL, respectively). Moreover, specific growth rate of the control experiment (0.23/day) was significantly lower than their of G1 to G3 experiment. The results indicated that the attachment substrate for benthic microalgae as Nitzschia sp. is important factor which affecting the growth rate as well as cell density. Therefore, the physiological experiment of benthic microalgae seems to be necessary to preliminary experiment, which is addition or not of the attachment suitable substrate and the grain size for the target species of benthic microalgae.

• Journal of Bio-Environment Control
• /
• v.15 no.2
• /
• pp.138-148
• /
• 2006

This study was carried out to evaluate the structural safety fur both the attached wind-protecting wall in greenhouse and the detached one installed outside. Regarding the attached wind-protecting wall in greenhouse, the analysis was conducted by doing a fluid-structure coupled field analysis using both CFX-5.7 and ANSYS 8.1 and also under the design condition of an instantaneous maximum wind velocity of $30.9m{\cdot}s^{-1}$. Three kinds of the width ranged from 30 to 90cm were considered in this study. With regard to the detached wind-protecting wall, the structural saffty was analyzed under the pressure difference of 1,117 Pa which corresponded to a wind velocity of $50m{\cdot}s^{-1}$ and the analytical results were also compared with theoretical ones. The result showed that there was little difference in the distribution of velocity overall and total pressure on the lateral side according to the width of the attached wind-protecting wall, but greenhouse with wind-protecting widths of 30 to 60cm has been reinforced to the extent of about 11% when compared with the case of being without the wall. The result also showed that the detached wind-protecting wall with a main-column interval of 3m was not stable so that it was necessary for the detached wind-protecting wall to be adequately reinforced to secure structural stability. Finally, there was great difference between analytical results and theoretical studies. The difference meant that there was some possibility of including errors when a theoretical study was done in three dimensional structure.

• Journal of Bio-Environment Control
• /
• v.12 no.3
• /
• pp.132-138
• /
• 2003

This experiment was conducted to investigate the mass propagation system of Aster glehni FR. and to obtain the basic data for improvement of germination and seedling. The following was the results of experimentation about temperature and light conditions, and priming treatment as kinds of chemicals, their concentration and treated periods affect germination of Aster glehni FR. The germination percentage of Aster glehni FR. seed was higher in 20 and 25$^{\circ}C$ than the others, but it dropped rapidly at 30$^{\circ}C$ and didn't germinate at 35$^{\circ}C$. The first day to germination was the slowest at 15$^{\circ}C$. The germination rate of Aster glehni FR seed increased with increasing with temperatures from 15 to 25$^{\circ}C$. But the seed was rotten easily in high temperature. The germination rate was shown highest in 25$^{\circ}C$, and next was 15, 20, 30$^{\circ}C$ in order. Light treatment enhanced germination percentage, the first day to germination, germination rate and T50, but there was no significant difference. The 3 hours priming treatments had more effect on germination percentage than 30 minutes treatments as comparing averages. Aster glehni FR seeds primed in $KNO_3+K_3PO_4$ for 3 hours had most eHective on germination percentage (83.3%) and also showed shortest $T_{50{\cdot}}T_{50}$ and day of first germination was better in 30 minutes than 3 hours treatments, and most of priming treatments were better than control(non-priming seeds). While priming seeds showed shorter day of first gemination than control, there was no significant difference between 30 minutes and 3 hours treatments.

• Journal of Bio-Environment Control
• /
• v.11 no.4
• /
• pp.205-216
• /
• 2002

This study was conducted to examine the effect of long-day (LD) period before short-day (SD) treatment on the vegetative growth of greenhouse-grown cut chrysanthemum cv. Reagan Improved at Wageningen Agricultural University, The Netherlands. Rooted cuttings of cut chrysanthemum cv, Reagan Improved were transplanted on 6th, 13th, 20th of September and all of them were treated with LD before SD treatment on 27th of September, The periods from transplanting until final harvest were 70, 77, and 84 days for 1, 2, and 3 week-LD treatment, respectively. The final plant height increased in the plot of 3 week-LD period and decreased in the plot of 1 week-LD period before the SD treatment. Total fresh weight and the leaf area were increased more in the plot of 3 week-LD period than that of 1 week-LD period, but the absolute growth rate after SD treatment was the same on plant growth rate and increase of the number of leaves in all treatments. The final dry matter production (g.m$^{-2}$ ) was increased more in the plot of 3 week-LD period than that of 1, 2week-LD period before SD treatment. Plant height and fresh weight were followed by the condition of LD period. In addition, dry mass production was highest in 3 week-LD period.

• Atmosphere
• /
• v.16 no.1
• /
• pp.33-48
• /
• 2006

A classification of snowfall type based on development mechanism is proposed using previous snowfall studies, operational experiences, etc. Five types are proposed: snowfall caused by 1) airmass transformation (AT type), 2) terrain effects in a situation of expanding Siberian High (TE type), 3) precipitation systems associated with extratropical cyclones (EC type), 4) indirect effects of extratropical cyclones passing over the sea to the south of the Korean peninsula (ECS type), and 5) combined effects of TE and ECS types (COM type). Snowfall events during 1981-2001 are classified according to the 5 types mentioned above. For this, 118 events, with at least one station with daily snowfall depth greater than 20 cm, are selected. For the classification, synoptic weather charts, satellite images, and precipitation data are used. For TE and COM types, local sea-level pressure chart is also used to confirm the presence of condition for TE type (this is done for events in 1990 and thereafter). The classification shows that 109 out of 118 events can be classified as one of the 5 types. In the remaining 8 events, heavy snowfall occurred only in Ullung Island. Its occurrence may be due to one or more of the following mechanism: airmass transformation, mesoscale cyclones and/or mesoscale convergence over the East Sea, etc. Each type shows different characteristics in location of snowfall and composition of precipitation (i.e., dry snow, rain, and mixed precipitation). The AT-type snowfall occurs mostly in the west coast, Jeju and Ullung Islands whereas the TE-type snowfall occurs in the East coast especially over the Young Dong area. The ECS-type snowfall occurs mostly over the southern part of the peninsula and some east cost area (sometimes, whole south Korea depending on the location of cyclones). The EC- and COM-type snowfalls occur in wider area, often whole south Korea. Precipitation composition also varies with the type. The AT-type has a snow ratio (SR) higher than the mean value. The TE- and EC-type have SR similar to the mean. The ECS- and COM-type have SR values smaller than the mean. Generally the SR values at high latitude and mountainous areas are higher than those at the other areas. The SR value informs the characteristics of the precipitation composition. An SR value larger than 10 means that all precipitation is composed of snow whereas a zero SR value means that all precipitation is composed of rain.

• The Journal of Korean Academy of Prosthodontics
• /
• v.43 no.1
• /
• pp.52-60
• /
• 2005

Purpose. The intent of this study was to evaluate the effects of curing conditions on self-curing denture base resins to find out proper condition in self-curing resin polymerization. Materials and methods, In this study, 3 commercial self-curing denture base resins are used Vertex SC, Tokuso Rebase and Jet Denture Repair Acrylic. After mixing the self curing resin, it was placed in a stainless steel mold(3$\times$6$\times$60mm). The mold containing the resin was placed under the following conditions: in air at 23$^{\circ}C$; or in water at 23$^{\circ}C$; or in water at 23$^{\circ}C$ under pressure(20psi); or in water at 37$^{\circ}C$ under pressure(20psi) or in water at 50$^{\circ}C$ under pressure(20psi) , or in water at 65$^{\circ}C$ under pressure(20psi), respectively. Also heat-curing denture base resin is polymerized according to manufactures' instructions as control. Fracture toughness was measured by a single edge notched beam(SENB) method. Notch about 3mm deep was carved at the center of the long axis of the specimen using a dental diamond disk driven by a dental micro engine. The flexural test was carried out at a crosshead speed 0.5mm/min and fracture surface were observed under measuring microscope. Results and conclusion . The results obtained were summarized as follows : 1. The fracture toughness value of self-curing denture base resins were relatively lower than that of heat-curing denture base resin. 2. In Vertex SC and Jet Denture Repair Acrylic, higher fracture toughness value was observed in the curing environment with pressure but in Tokuso Rebase, low fracture toughness value was observed but there was no statistical difference. 3. Higher fracture toughness value was observed in the curing environment with water than air but there was no statistical difference. 4. Raising the temperature in water showed the increase of fracture toughness.

• Journal of Digital Contents Society
• /
• v.16 no.1
• /
• pp.63-70
• /
• 2015

In this paper, we estimate the life cycle from acceleration life test about the hard disk of disk array of image storage of PACS. Webuil distribution was selected by the Anderson-Darling goodness-of-fit test with data of down time at $50^{\circ}C$ and $60^{\circ}C$. The equality test of shape parameter and scale parameter was conducted, so that the probability distribution estimated from data of down time at $50^{\circ}C$ and $60^{\circ}C$ was not statistically significant. The shape parameter was 1.0409, The characteristic life was 24603.5 hours at normal user condition($30^{\circ}C$) by the analysis of weibull-arrhenius modeling which included the acceleration factor of temperature, and The activation energy was 0.5011 eV through arrhenius modeling. The failure analysis of the failure samples of acceleration test and the samples of market return was conducted, so that the share percentage of failure mode was detail difference but the rank of share percentage was almost same. This study suggest the test procedure of acceleration test of hard disk drive in PACS using environment, and help the life estimation at manufacture and use.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.9 no.4
• /
• pp.253-262
• /
• 2006

In this paper, collision analysis is carried out between two FRP fishing boats. A computer simulation with finite element method is used to accomplish this objective. At first, a detailed geometric model of the boat is constructed using 3-D CAD program. The formation of a finite element from a geometric data of the boats is carried out using HYPERMESH that is the commercial software for mesh generation and post processing. Twelve collision configurations are established by combining two kinds of contact angle($90^{\circ},\;135^{\circ}$) and three different speed(5, 10, 15knot) for small and large boats. Collision analysis is accomplished using DYNA3D. Stress distribution and deformation shape are investigated for each collision condition. In general, $90^{\circ}$ collision angle generate larger stress than $135^{\circ}$ case and the collision for two moving boats showed larger maximum stress than the case that one is moving and the other is stationary. When analysis is carried out until 150ms contact parts of two boats are broken for 10 and 15knot collision speed, in which maximum stress is larger than ultimate strength of the material.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.18 no.2
• /
• pp.123-129
• /
• 2012

Cabotage means transportation of cargoes or passengers between two points within same country by vessel or aircraft which registered to foreign country. Cabotage regulation has justified by the protectionism in economic aspect and by national security in the defence of a country, thus most world's major countries including United States of America, Japan and European Union(outside EU) are executing cabotage. Even though Korean's controlled fleet ranked to 5th in the world, shortage and ageing of Korean domestic seafarers came to the restricted factor in the Korean domestic shipping. Resultingly Korean government permitted 530 Myanmarese and Indonesian seafarers to come on board in domestic vessel. In regarding to the Korean law, there are no direct relationship between boarding foreign crew in domestic vessel. However the baxic concept of cabotage will be spoiled by boarding foreign crew under the regulation of cabotage, so special treatment should be needed to cover the problems in coastal shipping arose form them. To minimize the problems derived from foreign crew, following actions are recommended; first, management skills of foreign crew are needed to overcome differences of communication and culture; second foreign crew supporting center should be established to counsel their difficulties; third, high level of manning companies should be promoted; forth, stabilized crew supply should be guaranteed by improving employment condition; finally, memorandum of understanding should be concluded between two countries to prevent seceders.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.18 no.1
• /
• pp.1-13
• /
• 2012

We measured various geochemical parameters, including the grain size, loss on ignition(LOI), total organic carbon(TOC), total nitrogen(TN), total sulfur(TS) and metallic elements, in surface sediment collected from 19 stations in Gamak Bay in April 2010 in order to understand the sedimentary types, the origin of organic matters, and the distribution patterns of alkali(Li, Na, K, Rb) and alkaline earth(Be, Mg, Ca, Sr, Ba) elements. The surface sediments were mainly composed of mud. The concentrations of Chlorophyll-a, TOC, TN, TS and LOI in sediment were the highest at the cultivation areas of fish and shellfish in the northern and southern parts of the bay. The redox potential(or oxidation-reduction potential) showed the positive value in the middle part of the bay, indicating that the surface sediment is under oxidized condition. The organic materials in sediment at almost all of stations were characterized by the autochthonous origin. Based on the overall distributions of metallic elements, it appears that the concentrations of alkali and alkaline earth elements except Ba in sediment are mainly influenced by the dilution effect of quartz. The concentrations of Sr and Ba are also dependent on the secondary factors such as the effect of calcium carbonate and the redox potential.