• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.7
• /
• pp.666-674
• /
• 2015

In this paper, we introduce an adaptive phase-comparison monopulse technique for angle estimation of two targets in the same antenna beam. The proposed method determines a more suitable technique(between conventional phase comparison monopulse technique and Zheng's method) based on interference between two targets in Fourier domain. Consequently, regardless of the interference, angles of each individual target can be accurately estimated by means of the proposed method. In simulations, we assumed that two point targets with same velocity are located in the same antenna beam, and the accuracy improvement of the proposed method is verified by using several simulations.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.4
• /
• pp.541-550
• /
• 2012

An improved method of moments using a hybrid Galerkin-interpolation technique for numerical analysis of electromagnetic wave scattering in the 3-dimensional space is presented in this paper. Basically, the EFIE(electric field integral equation) and RWG(Rao-Wilton-Glisson) basis function are used to compute a property of electromagnetic wave scattering. We propose a hybrid technique combining the existing Galerkin's method with the interpolation method to improve the efficiency of the numerical computation. Then, an index of relative distance of each cells was defined to distinguish the relatively far elements, which interpolation method can be applied. To verify the performance of the proposed technique, the analytical Mie-series solution was used to compute the theoretical RCS of a conducting sphere for the purpose of comparison. We also applied this hybrid technique to various scatterers such as trihedral/omni-directional corner-reflectors to analyze the radar backscattering properties.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.2
• /
• pp.275-280
• /
• 2016

In this paper, we propose a novel relay selection technique which utilizes a priori decoding information at relays for buffer-aided successive relaying networks. In the conventional relaying schemes, a single relay pair is selected for receiving data from the source and transmitting data to the destination. In the proposed technique, however, all relays except the relay selected for transmitting data to the destination try to decode the received signal from the source, and they store the data if they succeed decoding. The proposed technique selects the relay such that it can succeed its own transmission and it maximizes the number of relays successfully decoding the data from the source at the same time. It is shown that the proposed relaying technique significantly outperforms the conventional buffer-aided relaying schemes in terms of outage probability through extensive computer simulations.

• Korean Journal of Materials Research
• /
• v.25 no.1
• /
• pp.54-59
• /
• 2015

Glancing angle deposition (GLAD) is a powerful technique to control the morphology and microstructure of thin film prepared by physical vapor deposition. Chromium (Cr) thin films were deposited on a polymer substrate by a sputtering technique using GLAD. The change in thickness and Vickers microhardness for the samples was observed with a change in the glancing angle. The adhesion properties of the critical load (Lc) by a scratch tester for the samples were also measured with varying the glancing angle. The critical load, thickness and Vickers microhardness for the samples decreased with an increase in the glancing angle. However, the thickness of the Cr thin film prepared at a $90^{\circ}$ glancing angle showed a relatively large value of 50 % compared to that of the sample prepared at $0^{\circ}$. The results of X-ray diffraction and scanning electron microscopy demonstrated that the effect of GLAD on the microstructure of samples prepared by sputter technique was not as remarkable as the samples prepared by evaporation technique. The relatively small change in thickness and microstructure of the Cr thin film is due to the superior step-coverage properties of the sputter technique.

• Journal of Biomedical Engineering Research
• /
• v.27 no.4
• /
• pp.189-196
• /
• 2006

Micro computed tomography (micro-CT) has been used for in vivo animal study owing to its noninvasive and high spatial resolution capability. However, the sizes of existing detectors for micro-CT systems are too small to obtain whole-body images of a small animal object with $\sim$10 micron resolution and a part of its bones or other organs should be extracted. So, we have introduced the zoom-in micro-tomography technique which can obtain high-resolution images of a local region of an live animal object without extracting samples. In order to verify our zoom-in technique, we performed in vivo animal bone study. We prepared some SD (Sprague-Dawley) rats for making osteoporosis models. They were divided into control and ovariectomized groups. Again, the ovariectomized group is divided into two groups fed with normal food and with calcium-free food. And we took 3D tomographic images of their femurs with 20 micron resolution using our zoom-in tomography technique and observed the bone changes for 12 weeks. We selected ROI (region of interest) of a femur image and applied 2D FDT (fuzzy distance transform) to measure the trabecular bone thickness. The measured results showed obvious bone changes and big differences between control and ovariectomized groups. However, we found that the reliability of the measurement depended on the selection of ROI in a bone image for thickness calculation. So, we extended the method to 3D FDT technique. We selected 3D VOI (volume of interest) in the obtained 3D tomographic images and applied 3D FDT algorithm. The results showed that the 3D technique could give more accurate and reliable measurement.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.2274-2277
• /
• 2003

A cylindrical permanent magnet inside the four-phase permanent magnet (PM) stepping motor is employed as the rotor. The stator has four teeth around, which its coils are wound. The mode of excitation can be classified into 3 modes: single-phase excitation, two-phase excitation and ministep excitation. The ministep drive is a method to subdivide one step into several small steps by means of electronics. The paper presents the programmable ministep technique drive. This technique decodes the results obtained from the counter to locate the data in Read Only Memory (ROM). The Sinusoidal Pulse Width Modulation (SPWM) is transformed to binary file and saved to the ROM. The experiment is performed with the four-phase PM stepping motor and drives from a two-phase programmable sinusoidal ministep signal, instead of square wave. The results show that the performances of the proposed programmable ministep technique drive have high efficiency, smooth step motion, and high speed response. Moreover, the resolution of sinusoidal ministep signal can be controlled by the input frequency (f command).

• Proceedings of the Korean Geotechical Society Conference
• /
• 2004.03b
• /
• pp.775-782
• /
• 2004

Recently, the cases which are constructed close by neighboring structure or underground structure are on the increase to get the utmost out of the land exploitation of underground space in the downtown area. As the building becomes larger, the excavation depth is getting deep, and the excavation area is getting, wide too. These are frequent occasions that the application of Strut or Anchor method is difficult, because of site boundary, civil application and the ground condition. Therefore, to solve these problem, we analyze and compare design with measuring data, change the design factor and show the improvement of course through the application of self-supported diaphragm wall using counterfort technique which is a new method. It is expected to be a contribution to the suitable exploitation method of construction.

• Journal of Electrical Engineering and Technology
• /
• v.2 no.1
• /
• pp.106-111
• /
• 2007

Laser cutting with the micro-control technique has great potential to be employed for acrylic machining. In this paper, the optimal conditions of acrylic etching have been investigated. The three parameters such as laser power, moving velocity, and thickness of acrylic are experimented to find out optimal conditions. From these experimental results, we have known that it is very important to control accurate power by the TRIAC switching technique. The best condition of acrylic etching is performed 10 Wand 72 mm/sec at the plastic thickness of 1.33 mm. The other case is performed 10 W and 48 mm/sec, and 12 W and 56 mm/sec at the acrylic thickness of 2.00mm, respectively.

• The KIPS Transactions:PartD
• /
• v.8D no.2
• /
• pp.145-153
• /
• 2001

The Pyramid-Technique is based on mapping n-dimensional space data into one-dimensional data and expressing it as B-tree ; and by solving the problem of search time complexity the pyramid technique also prevents the effect \"phenomenon of dimensional curse\" which is caused by treatment of hypercube range query in n-dimensional data space. The Spherical Pyramid-Technique applies the pyramid method’s space division strategy, uses spherical range query and improves the search performance to make it suitable for similarity search. However, depending on the size of data and change in dimensions, the two above technique demonstrate significantly inferior search performance for data sizes greater than one million and dimensions greater than sixteen. In this paper, we propose a new index-structured PdR-Tree to improve the search performance for high dimensional data such as multimedia data. Test results using simulation data as well as real data demonstrate that PdR-Tree surpasses both the Pyramid-Technique and Spherical Pyramid-Technique in terms of search performance.

• 한국전산유체공학회:학술대회논문집
• /
• 2010.05a
• /
• pp.40-42
• /
• 2010

Unsteady CFD results of the backward facing step (BFS) flow field is reconstructed by the low-dimenstional modes using the POD (Proper Orthogonal Decomposition) technique. Flow responses to the blowing or suction with various frequencies and amplitudes applied at the edge of the BFS can also be analysed using the same technique. The present technique can be effectively applied to the feedback flow control device.