• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.6
• /
• pp.81-88
• /
• 2018

The present study evaluated the effective arrangement approach of transverse reinforcement in the jacket section for seismic strengthening of reinforced concrete columns. To simulate the full-scale columns, the section dimensions were determined as $450{\times}450mm$ for non-seismic existing columns and $750{\times}750mm$ for section enlargement strengthening columns. Over-lapped channel-shape bars and prefabricated bar units were proposed for closed-hoops in the jacket section, and conventional cross-ties anchored into existing columns and V-ties were considered for the supplementary ties. Test results showed that the axial capacity of the existing column and section enlargement columns with over-lapped channel-shape hoops was similar to the nominal strength calculated using ACI 318-14 procedure whereas the section enlargement column with prefabricated bar units possessed 1.25 times higher axial capacity than the nominal prediction. Furthermore, the axial ductility ratio of the section enlargement column with prefabricated bar unit was 139% higher than that of the existing column despite the potential size effect on ductility of concrete. Thus, it can be concluded that the developed prefabricated bar unit technique is practically useful for preventing the premature buckling of longitudinal reinforcement and confining core concrete in the section enlargement strengthening columns.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.6
• /
• pp.197-205
• /
• 2018

Recently, remodeling is increasing due to aging of buildings. Therefore, the importance of quality control of structures has been raised, and interest in safety diagnosis and evaluation of structures has been increasing. In order to accurately diagnose old buildings, a diagnostic evaluation technique is needed to evaluate the defects of structures in advance. In addition, as the safety diagnostic criteria for reconstruction are improved and the weight of structural safety is increased, researches on safety diagnosis techniques of structures that are faster and more reliable are needed. In this study, we tried to estimate the compressive strength by examining the correlation between ultrasonic pulse velocity and compressive strength of a 1 story structure consisting of vertical and horizontal members of reinforced concrete using ultrasonic pulse velocity method, which is one of the nondestructive testing methods. The purpose of this study is to examine the applicability in the field. As a result, the estimated average error rate of the compressive strength of the structure using the ultrasonic pulse velocity method was 28.7%, which confirmed the applicability in the field. However, in order to increase the accuracy of the estimation, the necessity of the reliable diagnostic method using the composite nondestructive testing method was confirmed.

• Journal of Intelligence and Information Systems
• /
• v.13 no.1
• /
• pp.1-14
• /
• 2007

Character images for the background screen of cell phones are one of the fast growing sectors of the mobile content market. However, character image buyers currently experience tremendous difficulties in searching for desired images due to the awkward image search process. Content-based image retrieval (CBIR) widely used for image retrieval could be a good candidate as a solution to this problem, but it needs to overcome the limitation of the mobile Internet environment where an initial query set (IQS) cannot be easily provided as in the PC-based environment. We propose a new approach, IQS-AutoGen, which automatically generates an initial query set for CBIR on the mobile Internet. The approach applies the collaborative filtering (CF), a well-known recommendation technique, to the CBIR process by using users' preference information collected during the relevance feedback process of CBIR. The results of the experiment using a PC-based prototype system show that the proposed approach successfully satisfies the initial query requirement of CBIR in the mobile Internet environment, thereby outperforming the current image search process on the mobile Internet.

• Journal of the Korean association of regional geographers
• /
• v.22 no.4
• /
• pp.792-808
• /
• 2016

Due to the high importance of foreign trade in the national economy, Korea has a lot of ports designated as trade ports compared to the small land size. However, because of the poor utilization results, some small trade ports have been criticized for wasteful financing due to redundant investment in SOC. This is because the characteristics and comparative advantage of foreign trade in trade ports have not been analyzed in detail by region. Therefore, this study analyzes the patterns and types of change in the size of trade, number of cargo items handled, and the number of trade target countries in the past 20 years for 19 domestic small trade ports using the time-series cluster analysis technique. As a result of analysis, Korean small trade ports were classified into five growth pattern types according to the analysis index, and characteristics and implications for each type could be derived. Today, as the foreign trade environment changes drastically and the importance of balanced regional development is emphasized, it is very important to study the growth types and implications of small trade ports and the results of this study are expected to provide meaningful implications for regional port development and operation in the future.

• Explosives and Blasting
• /
• v.24 no.2
• /
• pp.51-63
• /
• 2006

The typical blasting method adopted in Pasir Coal Mine is a surface blasting technique with a single free face. It means that there is only one free face, which is usually the ground surface. This kind of blasting method is easy to use but inevitably causes enormous ground vibrations, which, in turn, can affect the stability of the slopes comprising the various boundaries of the open pit mine. In addition, the method also has the problem of lowering the overall blast efficiency compared to other methods such as bench blasting methods or ones with more than two free faces. In this respect, a project was launched to develop a new blasting method that is suitable for both controling the ground vibration and enhancing the blast efficiency. As a part of the project, we investigated the current blasting method of the mine, and have conducted field measurements of the ground vibrations from 12 biasts. This Paper presents the details of the typical blasting pattern and the Propagation characteristics of the ground vibration from the surface blasting in the mine. Especially, various predictive equations for peak Particle velocities that can be used to estimate the ground vibration level in the mine area were derived from the regression analyses using the measured ground vibration data.

• Analytical Science and Technology
• /
• v.13 no.4
• /
• pp.403-411
• /
• 2000

This study described a method of thermoluminescence dating of pottery shards using subtraction method. TL measurement was achieved using two different types of samples prepared by quartz inclusion method and fine-grain technique. Fine grains (size range: $5-10{\mu}m$) were separated by suspending grounded pottery samples into acetone solution and sedimentation quantitatively. In quartz inclusion method quartz grains in the size range of 90 to $125{\mu}m$ diameter were obtained by extracting the quartz crystals embed in the pottery shards and etching them with 1.0 M HF solutions. The archaeological dose of both the quartz and fine grains was determined from the dose calibration curves obtained from sequential irradiation of $^{137}Cs$ gamma and $^{241}Am$ alpha source to the samples and TL measurement of natural samples, in which the alpha dose of 4.60 Gy for the Packjae pottery was obtained using subtraction method. Annual alpha dose rates ($3.05{\pm}0.11$ mGy/yr.) were determined by the analysis of U, Th contents in the pottery shards and evaluation of the values with Bell's equation. Dividing the alpha dose accumulated in the pottery shards by the annual alpha dose rate, we found age of approximately $1508{\pm}80$ years B.P. (AD. ca. 492 yr.) for the Packjae pottery. It matches well with the archeological age estimate (middle of 5th century) within 10 percent uncertainty and thereby conforms the age of the pottery sample.

• Applied Biological Chemistry
• /
• v.38 no.6
• /
• pp.507-511
• /
• 1995

In an attempt to improve the productivity of ${\beta}-galactosidase$ from Bacillus sp. A1, which was isolated from soil and has remarkably higher transgalactosylation activity than lactose hydrolysis activity, a chemical mutation procedure using N-methyl-N'-nitro-N-nitrosoguanidine followed by selection was conducted. The final selection, designated as Bacillus sp. A4442, turned out to show a substantially increased enzyme productivity. Catabolite repression by glucose and lactose requirement as an inducer for the enzyme biosynthesis, which were shown in the parent strain, was markedly diminished; instead it was found out that galactose acts as another inducer. Because pH of medium, one of the most important factors for cell growth as well as enzyme production, is closely related with the sugar concentration during culture, it was kept in the optimum range of $6.5{\sim}7.5$; for this the initial glucose concentration was adjusted to be 0.5% which was thereafter maintained by the controlled pumping-in of lactose using the pH-stat technique. By doing so, we were able to increase the productivity of ${\beta}-galactosidase$ with high transgalactosylation activity up to $44\;unit/m{\ell}-broth$.

• Journal of Navigation and Port Research
• /
• v.39 no.6
• /
• pp.457-463
• /
• 2015

A gas turbine engine plays an important role as a prime mover that is used in the marine transportation field as well as the space/aviation and power plant fields. However, it has a complicated structure and there is a time delay element in the combustion process. Therefore, an elaborate mathematical model needs to be developed to control a gas turbine engine. In this study, a modeling technique for a gas generator, a PLA actuator, and a metering valve, which are major components of a gas turbine engine, is explained. In addition, sub-models are obtained at several operating points in a steady state based on the trial running data of a gas turbine engine, and a method for controlling the engine speed is proposed by designing an NPID controller for each sub-model. The proposed NPID controller uses three kinds of gains that are implemented with a nonlinear function. The parameters of the NPID controller are tuned using real-coded genetic algorithms in terms of minimizing the objective function. The validity of the proposed method is examined by applying to a gas turbine engine and by conducting a simulation.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.2
• /
• pp.1339-1347
• /
• 2015

This study discusses a remote control torch system equipped with a GMAW double wire reel. The welding machine is 30m away from the wire feeder at the industrial site and the feeder is three to five meters away from the torch. Accordingly, the welders cannot control the current and voltage that meets the welding condition during work when they are working at a place that prevents them from seeing the control panel, such as inside a vehicle or tank or at a far work site. They also have no choice but to stop working to change the wire reel when it is burned out completely. Such work suspension resulting from frequent moves to adjust the current and voltage as well as to replace the wire and subsequent cooling causes welding defects. This study produced a remote control torch equipped with a double wire reel by simplifying and streamlining the existing GMAW functions to reduce the troubling issue. The remote control torch equipped with a double wire reel and the existing $CO_2$ /MAG welding torch were applied as a V-groove butt in the vertical position using 6mm rolled steel for a SM50A welding structure. After welding, the condition of welded surface beads underwent a visual inspection and radiographic inspection to analyze the welding quality inside the welded part. This study also evaluated the reduction of welding defects, cost saving, the replacing performance against the existing commercial welders, and the effects on possible compatibility.

• Journal of KIISE:Software and Applications
• /
• v.29 no.1_2
• /
• pp.80-90
• /
• 2002

Clustering is a useful technique for grouping data points such that points within a single group/cluster have similar characteristics. Many clustering algorithms have been developed and used in engineering applications including pattern recognition and image processing etc. Recently, it has drawn increasing attention as one of important techniques in data mining. However, clustering algorithms such as K-means and Fuzzy C-means suffer from difficulties. Those are the needs to determine the number of clusters apriori and the clustering results depending on the initial set of clusters which fails to gain desirable results. In this paper, we propose a new clustering algorithm, which solves mentioned problems. In our method we use evolutionary algorithm to solve the local optima problem that clustering converges to an undesirable state starting with an inappropriate set of clusters. We also adopt a new measure that represents how well data are clustered. The measure is determined in terms of both intra-cluster dispersion and inter-cluster separability. Using the measure, in our method the number of clusters is automatically determined as the result of optimization process. And also, we combine heuristic that is problem-specific knowledge with a evolutionary algorithm to speed evolutionary algorithm search. We have experimented our algorithm with several sets of multi-dimensional data and it has been shown that one algorithm outperforms the existing algorithms.