• Journal of Korea Fishing Vessel Association
• /
• v.29
• /
• pp.15-20
• /
• 1986

This paper describes on the measurement of the deck vibration produced by the main engine vibration of stern trawler MIS SAE-BA-DA (2,275GT, 3,600PS) while the ship is cruising and drifting. The obtained results are as follows; 1. The deck vibration level was the highest point at vertical line which pass main engine and the lowest point at vertical line which pass top bridge while the crusing. 2. The vibration source level of the main engine, screw shaft and screw propeller were respectively 110, 90 and 80% while the crusing. 3. The main deck vibration pressure level at the check points 2, 20, 30, 40, 60, 70, 80, 86m from the bow to stern was respectively 9, 8, 7, 10, 22, 45, 18, 23%. 4. The frequency distributions of the main engine, screw shaft, screw propeller vibration were from 3Hz to 10KHz, predominant frequency was 1KHz, each vibration accelration the highest level were respectively 1.3, 0.8, 0.5mm/$S^2$. 5. The predominant frequency distributions of the main deck, second deck, bridge deck and top bridge deck's vibration were from 10 to 30Hz, and each vibration accelration level were respe¬ctively 0.7, 0.05, 0.07, 0.04mm/$S^2$.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.04a
• /
• pp.139-145
• /
• 1997

Nowadays, the axial stiffness of crankshaft of long-stroke diesel engine is low compared to that of the old types of engine by increasing stroke/bore ratio and major critical speed might occur within engine operation speed. An axial damper needs to be installed in order to reduce the axial vibration of the crankshaft in the event of reduced or stopped axial damper function are discussed.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.3
• /
• pp.215-223
• /
• 2007

When the propulsion shafting system of marine diesel engine is designed. the vibratory stresses on shafts should be reviewed and be satisfied with limits which are laid down by classification societies In addition. the torsional vibration aspects for crankshaft of main engine are requested to be checked by engine designers. Especially. for the 4, 5, and 6-cylinder engines. the 2nd order moment compensator(s) may be installed to compensate the external moments of engine and not to excite the hull girder vibration. This moment compensator which is mounted on fore and/or after-end of engine is driven by the roller chain drive for some of MAN 2-stroke diesel engines. While the engine is running, the roller chain Is worn down, which causes the extension of roller chain. The chain therefore should be checked and tightened by periods in order to keep its functionality. However. when the torsional angular acceleration of chain drive exceeds the certain limit. the chain will suffer the excessive slack and transverse vibration. This may cause fatigue, wear or damage on the chain and the chain ultimately may be broken. The research object of this thesis is to review factors which affect the angular acceleration of chain drive and to find out how to decrease the angular acceleration of driving chain by checking factors which have a major contribution to acceleration reduction using the statistical method of DOE(design of experiment), correlation analysis and regression analysis methods.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.13 no.4
• /
• pp.107-112
• /
• 2007

The vibration generated on shipboard is very important because it greatly affects on the comfortable mind of passenger and working conditions of crews. Shipboard vibration is closely concerned with the development of propulsion method and the type of main engine to decide speed of ship. To make the propulsion power, the main engine of ship have continuous explosion process in engine room, so the shipboard vibration is generated. The shipboard vibration causes the physiological and psychological damages to human body. In the case of the human body exposed to the shipboard vibration, the evaluation of human exposure to whole-body vibration is prescribed in ISO 6954 : 2000(E). In this paper, to evaluate the shipboard working environment, two kinds of vibration levels onboard ship were measured and compared with one another between engine rooms, engine control rooms and wheel house by the regulation of ISO 6954 : 2000(E).

• Proceedings of KOSOMES biannual meeting
• /
• 2007.11a
• /
• pp.139-144
• /
• 2007

The vibration generated on shipboard is very important because it is greatly affect on the comfortable mind of passenger and working conditions et crews. Shipboard vibration is closely concerned with the development of propulsion method tint is main engine to decide speed of ship. To make the propulsion power, the main engine of ship engine room have continuous explosion process, so the shipboard vibration is generated The physiological damage and psychological damage of human body have caused by the vibration et shipboard In the case of the human body is exposed to the shipboard vibration, the evaluation of human exposure to whole-body vibration is prescribed in ISO 6954: 2000(E). In this paper, to evaluate the shipboard working environment, the vibration levels of two kinds of ship onboard were measured and compared with engine rooms, engine control rooms and bridges by the regulation of ISO 6954: 2000(E)

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.15 no.7 s.100
• /
• pp.865-870
• /
• 2005

Torque fluctuation of the engine and angular velocity variation of propeller shaft is the main excitation source for torsional vibration in the vehicle driveline. Experimental model for engine system is constructed with 4 cylinder 4 cycle diesel engine including Motor-Propeller Shaft-Axle-Wheel system. The angular velocity is measured by magnetic pickup and FV converter at the engine flywheel and propeller shaft. This paper presents the theoretical mechanism of these excitation sources and it is identified by the experimental methods.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.654-657
• /
• 2014

In this paper, we study the analytical method to predict the excitation forces for the engine system. The engine system on the construction equipment is one of the important power sources, and the characteristics of the engine decide the performance of noise and vibration for the equipment. We predict the excitation forces using the geometrical data of the crank system and the combustion pressure in the cylinder. The excited forces are represented by the torque fluctuation above the center of the crank shaft.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.284-285
• /
• 2008

For development of low fuel consumption vehicle, design of engine can he changed and it brings collateral effect. Abnormal vibration is one of bad effect of high efficiency engine and it can be got over by active engine mount system. For development of active engine mount system, an adequate experimental equipment is required which contain characteristic of real engine movement. To make adequate experimental equipment, regulated force vibrating system including characteristics of vehicle chassis is required.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.10a
• /
• pp.792-796
• /
• 2013

A practical process to optimize engine mounts on construction equipment is presented in this research. Transmitted force from the engine is estimated by using stiffness of the mount rubber which varies with frequency, amplitude and pre-load, and by the engine excitation force that comes from piston mass and gas pressure and so on. The transmitted force is measured through TPA(Transfer Path Analysis) and is then compared with the estimated force. The optimum mount position and stiffness are solved using MATLAB. The result shows the improvement on engine mount vibration.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.04a
• /
• pp.498-503
• /
• 2009

This paper presents the vibration problem of the Engine Casing (E/C) "B" deck in the handymax vessel and describes a method to avoid resonance. The first ship of the series did not have any vibration issue on the "B" deck. However, resonance condition occurred when additional machine was installed to the following vessels. To understand the dynamic characteristics of the deck, the normal mode analysis and impact test have been performed. Within the normal operating range of the vessel, the $1^{st}$ natural frequency of the E/C "B" deck is close to the main engine's $6^{th}$ order. Based on these analysis, a reinforcement on the deck was suggested and it proved to be effective. Since actual impact test after the reinforcement also confirmed the resonance avoidance.