• Polymer(Korea)
• /
• v.37 no.3
• /
• pp.399-404
• /
• 2013

In order to develop the blends with good long-term thermal stability and tensile elongation, the blends of polyphenylene sulfide (PPS) and 7 kinds of elastomer were tested. PPS/elastomer (90/10, 80/20, 70/30) blend samples were prepared by compression molding after twin screw extrusion or punching after sheet extrusion. Rheological, mechanical property and morphology of the blends were analyzed by capillary rheometer, UTM, impact tester, and SEM. For long-term thermal stability tests, the mechanical properties were measured again after the samples were stored in a convection oven for a week. The tensile strengths were almost same regardless of kinds of elastomer and the tensile elongation was the maximum for the PPS/m-EVA blend. As the content of elastomer increased, the elongation increased but delamination occurred at 30 wt% of elastomer content. The tensile strength increased but the elongation decreased seriously after thermal aging. Many problems related with PPS processing could be solved by adding a small amount of the elastomers partially compatibile with PPS and it would be applicable to develop various PPS grades.

• Journal of the Korean Society for Heat Treatment
• /
• v.10 no.2
• /
• pp.109-120
• /
• 1997

Microstructure and mechanical properties of Fe-Si-Mn-P high strength steel sheet have been investigated by controlling the cooling rate. Bainite and ferrite were obtatined by annealing in the ferrite pluse austenite region, and ferrite and austenite were obtatined after annealing in the fully austenite region. Ferrite and pearlite were obtained when the cooling rate was controlled from the annealing temperature above $760^{\circ}C$ and bainite showed with increasing cooling rate, however below $760^{\circ}C$ ferrite and bainite were obtained. Tensile strengths and hardness nearly unchanged with increasing cooling rate after control the cooling rate from the temperature above $760^{\circ}C$, while tensile strengths increased and elongation decreased with increasing cooling rate when the cooling rate was controlled from the tempeature below $760^{\circ}C$. Without regard to annealing temperature, tensile strength increased and elongation decreased with increasing cooling rate. Tensile strengths and elongation values heat treated in the ferrite plus austenite region were higher than those in the fully austenite region. Retained austenite and strength-elongation balance showed the maximum value at $780^{\circ}C$ and decreased with increasing annealing temperature. Strength-elongation balance value was controlled by the retained austenite.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.33 no.5
• /
• pp.418-422
• /
• 2000

The tensile properties and color of fish meal film under various processing conditions were measured to obtain basic data for biodegradable Alaska Pollack meal protein isolate (APMPI) film. The tensile strength and the elongation of APMPI film were increased with casting volume of APMPI solution but those of APMPI film were weakened with the addition of glycerol amount as well as reduction of pH values. In case of adding various plasticizer, the tensile strength of film was increased in order as follows: sorbitol, polyethylene glycol and glycerol. The elongation was increased in order of polyethylene glycol, sorbitol and glycerol. The tensile strength of film increased with increment of APMPI concentration, but the elongation of film was not affected by APMPI concentration. The tensile strength of APMPI film was decreased with the increment of relative humidity but its elongation was increased with the increment of relative humidity, Not only lightness and yellowness of film added with sorbitol but also redness and total different color of film added with polyethylene glycol showed the highest value in Hunter color system.

• Journal of Fisheries and Marine Sciences Education
• /
• v.25 no.4
• /
• pp.766-774
• /
• 2013

Biodegradable polybutylene succinate(PBS) is a kind of environmentally friendly plastics for fisheries, because it can mitigate the ghost fishing problem caused by gill-net and trap fisheries. To evaluate durability of PBS monofilament, each of different diameter 3 types of monofilaments were spun and exposed to 56 month outdoor and then their gravity, modification of surface, breaking strength, and elongation were analysed. The gravity of PBS monofilament was estimated to be approximately 1.24 when spinning ratio from 4.8 to 6.1. PBS monofilaments did not show any crack after 56 month exposed to outdoor and load-elastic elongation curve was showed sigmoid type. Decreasing ratio of elongation was appeared in the thinnest monofilament 0.2mm diameter and breaking strength was in the thickest monofilament 0.4mm diameter. Breaking strength and elongation at break were decreased rapidly after 48 month exposed to outdoor. Breaking strength reduced linearly after 48 month exposure, while no such linear relationship was found in the case of elongation at break. In results, it was investigated that the durability of PBS monofilament nets for gillnet and trap were 24, 50 month when keep to land, respectively.

• The International Journal of Costume Culture
• /
• v.7 no.2
• /
• pp.77-86
• /
• 2004

The purpose of this study is to characterize physical and tensile properties according to a knitting method as basic materials for solving the difficulties that occur due to the fact that the crosswise elongation is most different among knit stitch at the time of measuring elongation of knitwear. The sample used for this study was wool $100\%$ and was knitted into two, that is, controlled loop length controlled to properties of structure and fixed loop length by using Shimaseiki SES-124S 12G computer automatic flat knitting machine with DSCS device. Also, the density of rib fabric was 12gauge and its quantity was a total of seven of $0{\times}0,\;1{\times}1,\;2{\times}1,\;2{\times}2,\;3{\times}3,\;4{\times}4$ and including plain fabric, and knitted 2 pieces of sample of 300 wale${\times}400$ course. In conclusion, rib stitch has the much higher stretch rate in the direction of the course than other stitches.

• Journal of Korea Foundry Society
• /
• v.11 no.1
• /
• pp.63-70
• /
• 1991

Aluminium alloy castings, which can be not only manufactured in larger geometrically complex shapes, but also show good mechanical properties in addition to light weight, have kept their potential use as structures in the field of automotives, industrial machines and aircrafts. The variations of eutectic Si size a great effect on the elongation, impact value, fracture toughness and fatigue crack propagation rate without changes in the tensile strength or yield strength. The cooling curves with the solidification rate between $1.4^{\circ}C\;/min$ and $19.1^{\circ}C\;/min$ were obtained. With the increase of solidification rate, DAS, eutectic Si size and grain size were all decreased, which enhanced the mechanical properties. The tensile strength and yield strength were the most greatly influenced by DAS, and the elongation and impact value by eutectic Si size.

• Journal of Korea Foundry Society
• /
• v.32 no.4
• /
• pp.181-189
• /
• 2012

The microstructures of self-designed 7000 series Aluminium alloys added with Sc are observed. Moreover, the mechanical properties of the Sc-added Aluminium alloys are evaluated as a function of tensile temperature to establish the conditions of a following extrusion process. New casting conditions in the aluminium alloys added with Sc could be established by changing the casting speed and stirring time in the existing casting conditions of Aluminium alloys. The Sc addition results in $Al_3(Sc,Zr)$ precipitates in the cast alloys, and leads to the formation of equal-axed grains and fine grains. After homogenization heat treatment at $450^{\circ}C$, the Sc-added Aluminium alloys showed the highest elongation values in the temperature ranging from $300{\sim}400^{\circ}C$.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.842-845
• /
• 2000

The purpose of this paper is to investigate the influences on mechanical properties of motor pistons manufactured by casting, conventional forging and powder forging, using the comparison of characteristics like microstructure, hardness, tensile strength, and elongation. To form conventional forging piston, the experiment of visioplasticity was performed. As the model material, plasticine was used. To form powder forging piston, the shape of piston was simplified as simple cup shape. Material properties like workability, density variation before and after forging, and strain loci of material during forging were investigated. Powder forging and conventional forging technologies were effective to gain dense microstructure. In powder forging, distribution of such dense microstructuer was uniform. For hardness, pistons from powder forging and conventional forging technologies were much better than that from casting. For tensile strength and elongation, powder forging and conventional forging technologies were also advantageous.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2006.05a
• /
• pp.53-56
• /
• 2006

Magnesium alloy AZ31, which processed by conventional rolling or extrusion, has high anisotropy of mechanical properties in its strength and elongation at room temperature. We compared the influence of differential speed rolling with conventional rolling process on microstructure and mechanical properties of commercial AZ31 sheet. Commercial AZ31 alloy sheets were processed with conventional and differential speed rolling with thickness reduction ratio of 30% at a various temperature. The elongation of AZ31 alloy, warm-rolled by differential speed rolling is larger than those rolled by conventional rolling. Besides, grain size and distribution on microstructure of the conventional rolled materials were coarse and inhomogeneous, on the contrary, those of the differential speed rolled were fine and homogeneous.

• 연구논문집
• /
• s.29
• /
• pp.185-194
• /
• 1999

The shape and thickness distribution according to the pressure-time curve were carried out using the FEM and experiment. Also, mechanical properties were investigated. The square cup parts have been formed with pressure-time curve generated by result of analysis. The tensile strength and elongation have been investigated according to applied pressure conditions using the tensile test specimen obtained from the superplastic formed cup. We can use to predict the shape of formed part under the applied pressure using the FEM analysis. In the case of optimum pressure condition, the thickness distribution and mechanical properties were improved. From this study, we can find the important of optimum pressure-time condition. We have investigated about the forming of airplane part and fuel tank for motorcycle. If the applied load used in boundary conditions was appropriate, the simulation result coincides with the formed part. However, it is very difficult to define the pressure condition in complicated shape. Thus, it is need to develop the optimum pressure condition for superplastic forming.