• Elastomers and Composites
• /
• v.57 no.4
• /
• pp.165-174
• /
• 2022

The effect of fumed silica loading on the thermal stability and mechanical properties of fluorosilicone (FVMQ) rubber was investigated. The distribution of fumed silica inside FVMQ was characterized using scanning electron microscopy, and the thermal stability of composites was evaluated using thermogravimetric analysis and by the changes in mechanical performance during thermo-oxidative aging. The function mechanism of fumed silica was studied by Fourier transform infrared spectroscopy. The results show that with increasing silica content, the crosslink density of composites, the modulus at 100%, and tensile strength also increased, whereas the elongation at break decreased. Furthermore, increasing the silica content of composites increased the initial decomposition temperature (T_d) and residual weight of the composite after exposure to nitrogen. In addition, the thermal oxidative aging experiment demonstrated improved aging resistance of the FVMQ composites, including lower change in tensile strength, elongation at break, and modulus at 100%.

• Journal of the Korean Applied Science and Technology
• /
• v.39 no.6
• /
• pp.924-931
• /
• 2022

Undenatured castor oil and trimethylolpropane (TMP) were used to obtain bio-based water-based polyurethane. Isophorone diisocyanate (IPDI) was incorporated into the formulation to obtain a transparent film, and ethylenediamine (EDA) was used for chain extension. In order to measure the change in physical properties according to the contents of castor oil and TMP, each tensile strength, elongation, and abrasion resistance test was conducted. As the contents of castor oil and TMP increased, the tensile strength increased, the elongation decreased, and the surface hardened strongly as the respective contents increased.

• Fashion & Textile Research Journal
• /
• v.14 no.4
• /
• pp.629-634
• /
• 2012

Knitted fabric using acrylic/wool blended yarn (A/W) is increasingly used in the knit industry; subsequently, research on knitted fabric using A/W has increased. This study presents an scientific database from evaluating physical properties of $1{\times}1$ rib stitch using A/W. In this study,$1{\times}1$ rib stitch using A/W were made at various knitting tensions (dial no. 2-6) and the number (4-6) of ply yarn. The physical properties of $1{\times}1$ rib stitch using A/W were measured and analyzed. The density was in the range 5.5-6.4 wales/cm and 4.0-5.6 courses/cm, respectively. The density increased when less plying yarns and more knitting tension were added during knitting. The thickness was in the range of 1.592-2.362 mm and the tensile strength was in the range 32.75-53.63 Kgf/mm. The burst strength was in the range 107.8-139.2 $N/cm^2$. Thickness, tensile strength, and burst strength increased as the number of ply yarn and the knitting tension increased. The elongation and the recovery extension rate were in the range 102.29-112.13% and 96.4-97.7%, respectively. The heat retention rate was in the range 59.3-65.1%. There was no difference of the elongation and the recovery extension rate and the heat retention rate by the knitting tension and the number of the ply yarn. The permeability was in the range 170.5-396.3 $cm^3/cm^2/sec$. Air permeability decreased as the number of ply yarn and the knitting tension increased. The pilling properties were excellent for all $1{\times}1$ rib stitches.

• Journal of Microbiology and Biotechnology
• /
• v.15 no.4
• /
• pp.815-822
• /
• 2005

In order to extend the shelf-life of packaged or coated foods, an antibacterial edible film was developed from soybean meal that had been fermented with Bacillus subtilis under the optimum condition of pH 7.0-7.5 and $33^{\circ}C$ for 33 h. The water vapor permeability of the fermented film ($86.0 mg/cm^2{\cdot}h$) was higher than those of normal soybean films ($66.9 mg/cm^2{\cdot}h$). Protein solubility of the fermented film was also higher than ordinary soy protein film at the pH range of 3 -10. The fermented soybean film had higher tensile strength and lower $\%$ elongation (elongation rate) than the ordinary soybean film, mainly because partial hydrolysis of proteins in the soybean film occurred during fermentation. Antimicrobial properties of the fermented film on foodstuffs were measured by placing the films on surime, jerked beef, and mashed sausage media; containing $10^2-10^3$ CFU/plate of foodborne pathogenic bacteria, and showed significantly higher inhibitory effects on the growths of all the indicating bacteria. The film could be used as a packaging material in the food industry. However, before direct application of the fermented film to the commercial food industry, its poor mechanical and antibacterial properties need to be improved.

• Journal of the Korean Society of Safety
• /
• v.23 no.4
• /
• pp.99-104
• /
• 2008

In this research, magnesium hydroxide as a flame retardant agents and zinc borate as a synergist were mixed with LDPF/EVA blended samples, in order to improve their flame retardancy. We attempted to select the best mixing ratio of the LDPF/EVA blend and the optimum amount of magnesium hydroxide and zinc borate by the comparison and analysis of the flame retardancy, the electrical properties such as the volume resistivity and dielectric loss tangent, and the mechanical properties such as the tensile strength and elongation at break. Particularly, specimen which is the 6phr of zinc borate and 10phr of magnesium hydroxide 70/30phr adding to the LDPF/EVA blended samples has been most excellent in flame retardancy and electrical/mechanical properties.

• Korean Journal of Materials Research
• /
• v.22 no.1
• /
• pp.16-23
• /
• 2012

Research into the development of high strength (1 GPa) and superior formability, such as total elongation (10%), and stretch-flangeability (50%) in hot-rolled steel was conducted with a thermomechanically controlled hot-rolling process. To improve the overall mechanical properties simultaneously, low-carbon steel using precipitation hardening of Ti-Nb-V multimicroalloying elements was employed. And, ideal microstructural characteristics for the realization of balanced mechanical properties were determined using SEM, EBSD, and TEM analyses. The developed steel, 0.06C-2.0Mn-0.5Cr-0.2(Ti + Nb + V), consisted of ferrite as the matrix phase and second phase of granular bainite with fine carbides (20-50 nm) in both phases. The significant factor of the microstructural characteristics that affect stretch-flangeability was found to be the microstructural homogeneity. The microstructural homogeneity, manifest in such characteristics as low localization of plastic strain and internally stored energy, was identified by grain average misorientation method, analyzed by electron backscattered diffraction (EBSD) and hardness deviation between the phases. In summar, a hot-rolled steel having a composition 0.06C-2.0Mn-0.5Cr-0.2(Ti + Nb + V) demonstrated a tensile strength of 998 MPa, a total elongation of 19%, and a hole expansion ratio of 65%. The most important factors to satisfy the mechanical property were the presence of fine carbides and the microstructural homogeneity, which provided low hardness deviation between the phases.

• Fashion & Textile Research Journal
• /
• v.10 no.4
• /
• pp.566-571
• /
• 2008

Frictional sounds of 8 vapor permeable water repellent fabrics by sound generator were recorded and analyzed through FFT fast Fourier transform analysis. The frictional Sounds were quantified by calculating level pressure of total sound(LPT), the level range(${\Delta}L$) and the frequency difference(${\Delta}f$). Mechanical properties were measured by KES-FB. LPT values of specimens finished wet coating were higher than those of other kinds of finishing. ${\Delta}L$ values of specimens laminated were highest. Absolute values of ${\Delta}f$ were high in the cire finished and laminated specimens. Values for bending rigidity, shear stiffness and energy required for the compression of coated specimens increased compared with the cire finished and laminated specimens. Laminated specimens had high values of frictional coefficient and low values of surface roughness. Relationship between frictional sounds and mechanical properties analysed by use of correlation coefficients and stepwise regression. LPT showed significant correlation with elongation, tensile energy, geometrical roughness, weight and thickness. ${\Delta}L$ was highly correlated with tensile linearity, frictional coefficient, and ${\Delta}f$ with tensile linearity, weight and thickness. LPT were revealed to be explained by elongation and weight. ${\Delta}L$were predicted by tensile linearity, and ${\Delta}f$ by tensile linearity and thickness.

• Elastomers and Composites
• /
• v.50 no.1
• /
• pp.24-29
• /
• 2015

In this study, we investigated the effects of a crosslinking agent and a compatibilizer on the mechanical and rheological properties of waste PP and waste ground rubber tire (WGRT) composites. In order to simulate a commercial TPV, the component of waste PP and WGRT was fixed at 30 and 70 wt%, respectively. With the simple addition of SEBS-g-MA into the waste PP/WGRT composites, the tensile strength of the composite was decreased, whereas both the elongation at break and impact strength were significantly increased because of rubbery characteristics of SEBS-g-MA. In order to further improve the properties of the composites, the waste PP/WGRT/SEBS-g-MA composites was revulcanized with dicumyl peroxide (DCP). As expected, mechanical properties of the revulcanized composites was generally improved. Especially, with 15 and 1 phr of SEBS-g-MA and DCP, elongation at break was highest value of about 183% because of the recross-linking of WGRT without chain scission of the main chain. It was found that complex viscosity of the revulcanized composite increased which might verify further vulcanization of the WGRT.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.40 no.3
• /
• pp.495-505
• /
• 2016

This study explores and selects an appropriate material that considers light and soft physical properties as well as activity for impact absorption pads that can be used to develop practical impact protective clothes worn during daily life by the elderly to reduce the impact of falls. Physical properties, impact absorption performance, and compression characteristics were evaluated on 5 types of foam, 2 types of 3D spacer fabric, and 3 types of polymer gel to select a material appropriate for the pad to be inserted into impact protective clothes. The evaluation of the physical properties showed that 3D spacer fabrics had lower density compared to other materials and polymer gels had the highest density. The elongation percentage was higher in foams than 3D spacer fabrics and EPDM foam had the highest elongation percentage. The impact absorption performance of honeycomb polymer gel was better than foams and 3D spacer fabrics. As a result of looking into compression energy and compression characteristics of materials, 'CR foam A' was found to absorb the largest amount of compression energy, 24.1%, among foams and polymer gels. A high energy absorption rate of 50.0% (or above) was indicated by 3D spacer fabrics; however, foams and polymer gels showed a progressive deformation of energy compression / recovery curve with 3D spacer fabrics that showed drastic deformation. Based on characteristics of materials, 'CR foam C' and EPDM with relatively high absorption performance can be used as protective pad materials among foams. Among polymer gels, 2 open-type polymer gels that have relatively low impact protective performance but a relatively lighter weight on human body (compared to closed-type) are considered appropriate protective pad materials.

• Journal of Korea Foundry Society
• /
• v.23 no.4
• /
• pp.195-203
• /
• 2003

Hyper-eutectic Al-Si alloy is used much to automatic parts and material for the electronic parts because of the low coefficient of thermal expansion, superior thermal stability and superior wear resistance. In this work, A390 alloy specimens were fabricated for control of the Si particle size by various processes, such as spray-casting, permanent mold-casting and squeeze-casting. To minimize the effect of microporosity of the specimens, hot extrusion was carried out under equal condition. Each specimens were evaluated tensile properties at room temperature and thermal expansion properties in the range from room temperature to 400$^{\circ}C$. Ultimate tensile strength and elongation of the spray-cast and extruded specimens which have fine and well distributed Si particles were improved greatly compare to the permanent mold-cast and extruded ones. Specimens which have finer Si particles showed higher ultimate tensile strength and elongation than those having large Si particle size, and coefficient of thermal expansion of the specimens increased linearly with Si particle size. In case of the repeated high temperature exposures, thermal expansion properties of the spray-cast and extruded specimens were found to be more stable than those of the others due to the effect of fine and well distributed Si particles.