• Structural Engineering and Mechanics
• /
• v.63 no.3
• /
• pp.361-370
• /
• 2017

Through the use of finite element analysis and acoustic emission techniques we have evaluated the interfacial failure of a carbon fiber reinforced polymer (CFRP) repair patch on a notched aluminum substrate. The repair of cracks is a very common and widely used practice in the aeronautics field to extend the life of cracked sheet metal panels. The process consists of adhesively bonding a patch that encompasses the notched site to provide additional strength, thereby increasing life and avoiding costly replacements. The mechanical strength of the bonded joint relies mainly on the bonding of the adhesive to the plate and patch stiffness. Stress concentrations at crack tips promote disbonding of the composite patch from the substrate, consequently reducing the bonded area, which makes this a critical aspect of repair effectiveness. In this paper we examine patch disbonding by calculating the influence of notch tip stress on disbond area and verify computational results with acoustic emission (AE) measurements obtained from specimens subjected to uniaxial tension. The FE results showed that disbonding first occurs between the patch and the substrate close to free edge of the patch followed by failure around the tip of the notch, both highest stress regions. Experimental results revealed that cement adhesion at the aluminum interface was the limiting factor in patch performance. The patch did not appear to strengthen the aluminum substrate when measured by stress-strain due to early stage disbonding. Analysis of the AE signals provided insight to the disbond locations and progression at the metal-adhesive interface. Crack growth from the notch in the aluminum was not observed until the stress reached a critical level, an instant before final fracture, which was unaffected by the patch due to early stage disbonding. The FE model was further utilized to study the effects of patch fiber orientation and increased adhesive strength. The model revealed that the effectiveness of patch repairs is strongly dependent upon the combined interactions of adhesive bond strength and fiber orientation.

• Applied Biological Chemistry
• /
• v.38 no.1
• /
• pp.49-54
• /
• 1995

To understand the molecular structure and pathogenesis mechanism of Korean garlic viruses, we have isolated cDNA clones for garlic viruses. The partial nucleotide sequences of 24 cDNA clones were determined and those of five clones containing poly(A) tail were compared with sequences of other plant viruses. One of these clones, V9, has a primary structure similar to the carlavirus group, suggesting that the clone V9 derived from a part of garlic latent virus (GLV). Northern blot analysis with the clone V9 as a probe demonstrated that GLV genome is 8.5 knt long and has a poly(A) tail. The clone V9 encodes coat protein (CP) of 33 kDa and nucleic acid binding protein of 10 kDa in different reading frame. The hexanucleotide motif, 5'-ACCUAA, which is conserved in the 3' noncoding region arid was proposed to be a cis-acting element involved in the production of negative strand genomic RNA was noticed. Complementary sequence to the hexanucleotide motif, 5'-TTAGGT, is also found in the positive strand of V9 RNA. The putative CP gene was cloned into the pRSET-A expression vector and expressed in E. coli BL21. The expressed recombinant V9CP protein was purified by $Ni^{2+}$ NTA affinity chromatography. The anti-V9CP antibody recognizes 34 kDa polypeptide which could be CP of GLV in infected garlic leaf extract. Immunoblot and Northern blot analysis of various cultivars shows wide occurrence of GLV in Korean garlic plants.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.29 no.6
• /
• pp.787-796
• /
• 1996

The biodegradation experiment, the TOD analysis and the element analysis for dispersant, Bunker-A oil and Bunker-B oil were conducted to study the biodegradation characteristics of a mixture of Bunker-A oil with dispersant and a mixture of Bunker-B oil with dispersant in the seawater. The results of biodegradation experiment showed 1mg of dispersant to be equivalent to 0.26 mg of $BOD_5$ and to 0.60 mg of $BOD_{20}$ in the natural seawater. The results of TOD analysis showed each 1 mg of dispersant, Bunker-A oil and Bunker-B oil to be equivalent to 2.37 mg, 2.94 mg and 2.74 mg of TOD, respectively. The results of element analysis showed carbon, hydrogen, nitrogen and phosphorus contents of dispersant to be $82.1\%,\;13.8\%,\;1.8\%\;and\;2.2\%$, respectively. Carbon and hydrogen contents of Bunker-A oil were found to be $73.3\%\;and\;13.5\%$, respectively, and carbon, hydrogen and nitrogen contents of Bunker-B oil to be $80.4\%,\;12.3\%\;and\;0.7\%$, respectively. Accordingly, the detection of nitrogen and phosphorus in dispersant shows that dispersants should be used with caution in coastal waters, with relation to eutrophication. The biodegradability of dispersant expressed as the ratio of $BOD_5/TOD$ was found to be $11.0\%$. As the mix ratios of dispersant to Bunker-A oil (3 mg/l) and a mixture of Bunker-B oil (3mg/l) were changed from 1 : 10 to 5 : 10, the biodegradabilities of a mixture of Bunker-A oil with dispersant and Bunker-B oil with dispersant increased from $2.1\%\;to\;7.2\%$ and from $1.0\%\;to\;4.4\%$, respectively. Accordingly, the dispersant belongs to the organic matter group of middle-biodegradability while mixtures in the mix ratio range of $1:10\~5:10$ belong to the organic matter group of low-biodegradability. The deoxygenation rate constant $(K_1)$ and ultimate biochemical oxygen demand $(L_0)$ obtained from the biodegradation experiment and Thomas slope method were found to be 0.125/day and 2.487 mg/l for dispersant (4 mg/l), respectively. $K_1\;and\;L_0$, were found to be $0.079\~0.131/day$ and $0.318\~2.052\;mg/l$ for a mixture of Bunker-A oil with dispersant and to be $0.106\~0.371/day$ and $0.262\~1.106\;mg/l$ for a mixture of Bunker-B oil with dispersant, respectively, having $1:10\~5:10$ mix ratios of dispersant to Bunker-A oil and Bunker-B oil. The ultimate biochemical oxygen demands of the mixtures increased as the mix ratio of dispersant to Bunker-A, B oils changed from 1 : 10 to 5 : 10. This suggests that the more dispersants are applied to the sea for the cleanup of Bunker-A oil or Bunker-B oil, the more decreases the dissolved oxygen level in the seawater.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.26 no.3
• /
• pp.270-280
• /
• 2016

This paper investigates the evolution of EM admittance of piezoelectric transducers mounted on a notched beam from wave propagation perspective. A finite element analysis is adopted to obtain numerical solutions for Lamb waves reverberating on the notched beam. The mode-converted Lamb wave signals due to a notch are extracted by using the polarization characteristics of piezoelectric transducers collocated on the beam. Then, a series of temporal spectrums are computed to demonstrate the evolution of EM admittance through fast Fourier transform of the mode-converted Lamb wave signals which are consecutively truncated in the time domain. When truncation time is relatively small, the corresponding temporal spectrum is governed by the characteristics of the input driving frequency. As truncation time becomes large, however, the modal characteristics of the notched beam play a crucial role in the temporal spectrum within the input driving frequency band. This implies that mode-converted Lamb waves reverberating on the beam contributes to the resonance of the beam. The root mean square values are computed for the temporal spectrums in the vicinity of each resonance frequency. The root mean square values increase monotonically with respect to truncation time for any resonance frequencies. Finally the implications of the numerical observation are discussed in the context of damage detection of a beam.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.16 no.3
• /
• pp.162-173
• /
• 1996

Dry magnetic particle inspection(MPI) was performed to detect the surface defects of steel ingot cast billets. Magnetic properties of several materials were characterized by the measurement of the B-H hysteresis curve. The inspection results were evaluated in terms of the magnetizing current, temperature, and the amount of magnetic particles applied to billets. Magnetic flux leakage near the defect site of interest was measured and compared with the results of calculation by the finite element method in the case of direct magnetizing current. Direct and alternating magnetizing currents for materials were deduced by the comparison of the inspections. Results of the magnetic particle inspection by direct magnetizing current were compared with those of finite element method calculations, which were verified by measuring magnetic leakage flux above the surface and the surface defects of the material. For square rods, due to the geometrical effect, the magnetic flux density at the edges along the length of the rods was about 30% of that at the center of rod face for a sufficiently large direct magnetizing current, while it was about 70% for an alternating magnetizing current. Thus, an alternating magnetizing current generates rather uniform magnetic flux density over the rods, except for the region on the face across about 10 mm from the edge. The attraction of the magnetic particle by the magnetic leakage field was nearly independent of the surface temperature of the billets up to $150^{\circ}C$. However, the temperature should have been limited below $60^{\circ}C$ for an effective fixing of gathered magnetic particles to the billet surface using methylene chloride. We also found that the amount of applied magnetic particles tremendously affected the detection capability.

• Journal of Life Science
• /
• v.12 no.2
• /
• pp.188-199
• /
• 2002

A gene coding for xylanase from thermo-tolerant Bacillus pumilus TX703 was cloned into Escherichia coli DH5 $\alpha$ using pUC19. Among 7,400 transformants, four transformants showed clear zones on the detection agar plates containing oat-spells xylan. One of them which showed highest xylanase activity was selected and its recombinant plasmid, named pXES106, was found to carry 2.24 kb insert DNA fragment. When the nucleotide sequence of the cloned xylanase gene (xynK) was determined, xynK gene was found to consist of 1,227 base-pair open reading frame coding for a polypeptide of 409 amino acids with a deduced molecular weight of 48 kDa. The coding sequence was preceded by a putative ribosome binding site, the transcription initiation signals, and cia-acting catabolite responsive element. The deduced amino acids sequence of xylanase is similar to those of the xylanases from Hordeum vulgare (barley) and Clostridium thermocellum, with 39 and 31% identical residues, respectively. The amino acids sequence of this xylanase was quite different from those of the xylanases from other Bacillus species.

• Analytical Science and Technology
• /
• v.22 no.3
• /
• pp.235-246
• /
• 2009

The analyses of minor and trace elements in glass debris were performed using LA-ICP-MS in order to identify manufacturers using real commercial samples. At first, a calibration curve was made using standard glass samples of NIST 610, 612, 614 and 616. $^{29}Si$ was used as an internal standard, and the ratios of metal/Si for each metal were compared with their concentrations. Based on elements in each sample and standard materials, 24 metals were quantified and the LOD in analysis, according to the blank sample, was in the range of 0.11 mg/kg (Ti)-4.91 mg/kg (Ca). Eleven samples from two manufacturers were collected and five sub-samples were taken from each sample for analysis. 15 elements (Co, Ce, Ca, Mn, Sr, Ba, Li, Rb, U, La, Th, Na, Al, Zr and Hf) were selected to identify manufacturers because some elements (Cu, Cr, Cd and Ni) were below the detection limit and some elements (Ti, Pr, Mg, Nb, Nd) were absent in the analysis of standards and others (Pb and Sn) had a problem of homogeneity. The attempts to identify manufacturers and the manufacturing period were performed through a triangular diagram. In the manufacturer discrimination by discriminant analysis, a canonical discriminant function was made based on Mn, Ce and Rb, and each sample could be identified.

• Journal of Digital Contents Society
• /
• v.13 no.1
• /
• pp.43-52
• /
• 2012

For accurate search on information resources, it is needed to manage gradual changes in ontology efficiently. Recently, because ontology is often written using OWL, techniques that can manage changes in OWL documents are required. To meet these needs, in this paper, we classify changeable elements to detect changes in OWL ontology and propose a storage schema that can manage the changes according to the characteristics of each element. And we suggest the possibility of improving performance of query processing using views that provide information about classes or properties in each ontology version. The proposed storage schema stores changes in metadata associated with each ontology version. In addition, it can manage metadata that must be added or deleted through reasoning when ontology changes. So, the proposed storage schema can support queries about history of changes in ontology and provide accurate and valid metadata that is suitable for user-selected ontology version.

• Journal of the Ergonomics Society of Korea
• /
• v.31 no.1
• /
• pp.23-32
• /
• 2012

Objective: This research proposes a methodology, which validates a grasp of the customers' emotions in the service design area. Background: As the era of service design has taken its approach, the need for a deliberate design that would reflect the customer's experience had emerged in the area of service. Therefore, a variety of methodologies has been adopted in the field of service design with the purpose of discovery of the customers' needs. Even though the importance of an emotion-sentient research of a service experience increases, its research progress remains to be inadequate in comparison to all the other areas. Method: Having had taken some resources from the emotional studies under other areas of expertise as a base, the concept of volatility of emotions has been introduced as the core element of this research, further followed by an elaboration of its special characteristics. The observation technique under Stakeholder's system: SOMC(Simultaneous Observation Method based on Cooperation) has been proposed in this study as it presents an effective way to grasp the concept of volatile emotions in contrast to the previously existent types of methodologies. Results: The SOMC rather supplements the existing research methods than substitutes the previous ones. In other words, although the existing research system allowed emotion detection, it was difficult to capture the change of momentary and fickle emotions. On the opposite, the SOMC provides a condition allowing a sufficient grasp of the customer's emotions and facilitates emotional capture. Conclusion: For that reason, it is hoped that this piece of research represents a valuable and effective approach in terms of grasping the true needs of the customers on the emotional level, which will in its turn contribute to the improvement of the service quality in the midst of a complicated service condition. Application: Moreover, the purpose of this research is that in its outcome it may serve as a sufficient contribution to the area of emotional studies within the field of service design.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.33 no.3
• /
• pp.193-199
• /
• 2020

This study examines a method for identifying stiffness reductions in structures subjected to seismic loads and retrofitting effects using a combination of the finite element method and an advanced genetic algorithm. The novelty of this study is the application of seismic loading and its response to anomalies in the tested structure. The technique described in this study may enable not only detection of damaged elements but also the identification of their locations and the extent of damage due to seismic loading. To demonstrate the feasibility of the method, the advanced genetic algorithm is applied to frame and truss bridge structures subjected to El Centro and Pohang seismic loads. The results reveal the excellent computational efficiency of the method and its ability to prevent severe damage from earthquakes.