• 한국응용과학기술학회지
• /
• 제32권3호
• /
• pp.405-411
• /
• 2015

Carbon composites for flexible fiber heating element were examined to improve the electrical conductivity in this study. Carbon composites using carbon black, denka black, super-c, super-p with/without CNF or dispersant such as BCS03 and Sikament-nn were prepared. Carbon composite slurry was coated on plane film and yarns(cotton, polyester) and the performances of prepared heating materials were investigated by checking electrical surface resistance, adhesion strength. The plane heating element using carbon black under natural drying condition($25^{\circ}C$) had better physical properties such as surface resistance(185.3 Ohm/sq) and adhesion strength(above 90%) than those of other carbon composite heating elements. From these results, polyester heating element coated by carbon black showed better electrical line resistance(33.2 kOhm/cm) than cotton heating element. Then, it was found that polyester heating element coated by carbon black with CNF(3 wt%) and BCS03(1 wt%) appeared best properties(0.604 kOhm/cm).

• 정보학연구
• /
• 제10권2호
• /
• pp.37-45
• /
• 2007

The multiple-ability which the structure and the physical properties which the carbon or scull tube are unique show the applicability is superior in the plane indication element which is an indispensability of information communications apparatus, the stubbornness memory element, 2nd change of air and the rough copy dosage [khay] plaque seater, the hydrogen store material and the chemical sensor back and it has the possibility which will pass over the limit which the element of existing has. from the present paper it compared in the steel and only 10 the boat it did and it analyzed against an energy storage space voluntary application and developmental apply the carbon or scull tube trend in order about under researching the effective energy storage element it could be appeared, the technique of the strong carbon nano tube. 1. The hazard which embodies the energy storage element which uses the carbon or scull tube it follows in the function which stands and CNT of the structure which is various is necessary. 2. CNT fabrications of each one must precede possible not only must be each Cabinet conference circumstances quality gain and loss. 3. The structural control of syntheses, length controls, diameter controls and the metal - CNT junction control backs of quality CNT must precede. Applies the hereafter carbon or the scull tube in the various element with the primary preceding base technique for the structural plan technique of the carbon or scull tube to be certainly established, it does, secondarily the various element functional control technique which uses the carbon or scull tube is researched and will do.

• Structural Engineering and Mechanics
• /
• 제64권3호
• /
• pp.329-337
• /
• 2017

This study concerns the vibrational behavior of multi-walled nested silicon-carbide and carbon nanotubes using the finite element method. The beam elements are used to model the carbon-carbon and silicon-carbon bonds. Besides, spring elements are employed to simulate the van der Waals interactions between walls. The effects of nanotube arrangement, number of walls, geometrical parameters and boundary conditions on the frequencies of nested silicon-carbide and carbon nanotubes are investigated. It is shown that the double-walled nanotubes have larger frequencies than triple-walled nanotubes. Besides, replacing silicon carbide layers with carbon layers leads to increasing the frequencies of nested silicon-carbide and carbon nanotubes. Comparing the first ten mode shapes of nested nanotubes, it is observed that the mode shapes of armchair and zigzag nanotubes are almost the same.

• 한국산학기술학회논문지
• /
• 제19권2호
• /
• pp.683-688
• /
• 2018

본 논문에서는 탄소섬유를 이용한 면상발열체의 발열 상태를 영상처리 기술을 이용한 분석을 제안하였다. 면상발열체의 제작 방법은 탄소섬유를 작게 잘라 촙 상태로 만든 다음 분산제를 통하여 다시 결합시켜 준다. 그 다음 부직포 위에 분산제를 통해 결합된 탄소섬유 용액을 필터링 한다. 마지막 단계는 필터링된 탄소섬유를 건조 하면 부직포 형태의 면상 탄소 섬유를 얻을 수 있다. 면상발열체는 이렇게 제작된 면상 탄소 섬유에 전기를 인가하면 된다. 본 논문에서는 면상발열체를 4가지 방법으로 분석하였다. 분석 방법 중 면상 발열체의 발열특성 분석과 면상발열체의 발열속도 분석은 제작된 면상발열체가 정상군에 해당하는지를 확인한다. 절연 코팅 및 면상 발열체 모듈 분석은 실제 제품의 제작에 사용될 수 있는 면상발열체에 대해 영상처리 기술을 이용하여 2차원 이미지 분석이다. 면상발열체의 열화상 이미지 분석은 2차원 및 3차원으로 발열 상태를 분석할 뿐만 아니라, 발열의 상위온도 15~20%와 하위온도 15~20%를 이미지에 표시하는 프로그램 기법이다. 마지막 분석은 제작된 면상발열체의 상태를 화면에 직접 보여줌으로써 제작 과정 중 잘못된 부분을 쉽게 찾을 수 있다. 이와 같은 면상발열체의 이미지 분석 방법은 기존의 방법과 결합하여 발열상태를 더욱 정밀하게 분석할 수 있었다.

• 한국대기환경학회지
• /
• 제25권2호
• /
• pp.122-132
• /
• 2009

Adsorption of toluene by activated carbon fiber (ACF) coated with dielectric heating element and desorption by applying microwave were investigated. In order to prepare adsorbent so that VOC can be desorbed by microwave heating, fine dielectric heating element with nano size was coated on the surface of the ACF using hybrid binder. Eight adsorbents (ACF-DHE, Activated Carbon Fiber coated with Dielectric Heating Element) were prepared with different amount of dielectric heating element, kinds of hybrid binder, and solvent. In order to investigate adsorption characteristics, BET surface area, pore volume, and average pore size were measured for each adsorbent including ACF. Breakthrough experiments with toluene concentration, flow rate, bed length using fixed bed reactor were performed to investigate adsorbality of adsorbent, and results were compared with that of the ACF. Desorption reactor was constructed with modified microwave oven to investigate heating effect on ACF-DHE by applying microwave power. Each adsorbent saturated with toluene were put into desorption reactor. Composition of desorbed gas generated by applying controlled microwave power to reactor was measured. Up to now, hot air desorption method has been used. Experimental results showed that desorption method with new adsorbent prepared by coating dielectric heating element on ACF can be used for industrial application.

• Carbon letters
• /
• 제15권4호
• /
• pp.219-237
• /
• 2014

The element carbon has been used as a source of energy for the past few hundred years, and now in this era of technology, carbon has played a significant and very prominent role in almost all fields of science and technology. So as an honour to this marvellous element, we humans should know about its various forms of existence. In this review article, we shed light on all possible carbon-allotropes; similarities in their synthesis techniques and the starting materials; their wide range of possible availability; and finally, future perspectives and applications. A brief introduction is given on the types, structures, and shapes of the allotropes of carbon for a better understanding.

• 한국기계가공학회지
• /
• 제19권1호
• /
• pp.1-10
• /
• 2020

This study deals with the fabrication and thermal characterization of planar heating elements attached to the backside of the reflector used in the electrodeless lamp of a freezer. We tried to solve the problem of the local heat generation of the linear heating element that occurs about 50℃. The homogeneous dispersion and manufacturing excellence of the planar heating element produced were confirmed through SEM and EDS. In addition, the test specimens was prepared according to the change in the ratio of carbon fiber to the basis weight of the planar heating element, and a sample having a basis weight of 50g/㎡ having a content ratio of carbon fiber of 70% was selected. That sample showed low surface resistance of 4.3Ω/sq and high temperature of about 81℃ at 6V. Durability was confirmed by performing repeated bending evaluation of 3000 cycles for the sample. Large area test specimens were prepared to be applied to the actual reflector, insulated by EVA film and analyzed for their thermal characteristics. From 13V application, the temperature of the linear heating element was higher than 50℃ and the average temperature of 68℃ was maximum at 18V.

• 한국방사선학회논문지
• /
• 제9권3호
• /
• pp.131-137
• /
• 2015

본 연구의 목적은 기존에 사용 중인 X선 발생장치의 촬영대를 따뜻하게 가열하면서도 X선 감약이 적은 탄소나노튜브(carbon nano tube, CNT) 발열체를 사용하여 가열장치를 구비한 X선 발생장치용 부착형 촬영대의 고안 및 설계를 하고자 한다. 고안된 제품의 구성은 부착형 탄소발열체 촬영대로서 기존 X선 촬영대, 탄소나노튜브 면상발열체, 전극선, 난연 처방된 보호필름과 바닥필름으로 구성되어 있다. 본 고안 제품의 특징과 장점은 냉기(冷氣)를 느끼는 촬영대에서 환의를 착용하고 검사를 받는 환자에게 온화한 느낌과 안전감을 제공하고 심적인 불안감을 해소하여 검사에 도움을 줄 수 있기 때문에 임상 적용을 적극 권장하는 바이다.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2003년도 추계 학술발표회논문집
• /
• pp.147-154
• /
• 2003

The purpose of this study is to investigate analytically the flexural behavior characteristics of Circular concrete beams confined by carbon sheet. Nonlinear analysis method is presented to simulate the structural behavior beam models. The proposed analytical hardening models were considered the confinement effect of concrete and the tensile effect of carbon sheet in tensile region of concrete. Prandtl-Reuss numerical formula was used to nonlinear analysis of finite element models. Comparisons analytical models with experimental data obtained from flexural testing in the laboratory were presented. Analytical and experimental models show similar behavior.

• 한국생산제조학회지
• /
• 제9권3호
• /
• pp.69-75
• /
• 2000

The object of the research is to estimate for pearlite structure of quenched carbon steels. The effects of temperature on physical properties metallic structures and the latent heat by phase transformation were considered. In this study a set of constitutive equations relevant to the analysis of thermo-elasto plastic materials with pearlite phase transformation during quenching process way presented on the basis of continuum thermo-dynamics. The iso-thermal transformation curve of the SM50C was formlated by cubic spline curve. The formulated equations of evolution in pearlite transformation was used for structure analysis. The volume fraction of pearlite was obtained from the results of calculated metallic structure by Finite element equation.