• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.249-249
• /
• 2009

We have grown large area BSTO($(Ba_{1-x}Sr_x)TiO_3$) thin films (x=0.4) on 2 inch diameter MgO (001) single crystal substrates using a pulse laser deposition(PLD) system. Substrate temperature and oxygen pressure in the deposition chamber, and the laser optics for ablating a target have been controlled to obtain the uniform thickness and preferred orientation of the films. Results of x-ray diffraction and rocking curve analysis revealed that the BSTO films were grown on MgO substrates with a preferred orientation (002), and the full width half maximum of the rocking curve was measured to be 0.86 degree at optimum condition. Roughness of the films have been measured to be $3.42{\AA}$ rms by using atomic force microscopy. We have successfully deposited the large area BSTO thin films of $4000{\AA}$ thickness on 50 mm diameter MgO substrates.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07a
• /
• pp.61-63
• /
• 2005

Pentacene based OTFT on PC and PES plastic substrates have been fabricated in a scale of 5 inches. We could get a small OTFT device enough to be applicable for AMOLED by acquiring the at least misalignment margin through a contact aligner. And also we could find out the degradation of device parameter through the integration processes and improve the properties by using a buffer layer as an etch stopper in an active patterning. Through these, the mobility of device is more than about $0.2cm^2/Vs$ and $I_{on}/I_{off}$ is higher than $10^5$.

• The Magazine of the IEIE
• /
• v.20 no.10
• /
• pp.23-37
• /
• 1993

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1998.08a
• /
• pp.42.3-42
• /
• 1998

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1103-1107
• /
• 2004

Last year, we introduced a TFT-LCD with RGBW color system. The primary advantage of the RGBW system is that its optical efficiency is at least 50% higher than the RGB system. However, it is not a simple task to incorporate the new color system into the infrastructure of the RGB system: the driving circuitry, fabrication of color filter, and color conversion. In this report, the practical hurdles are discussed and the solutions are presented.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.85-88
• /
• 2004

2-inch qVGA (240${\times}$320) TFT-LCD with integrated 6-bit source driver is reported. The pixel density is over than 200ppi and the operation frequency is about 2.8MHz. In order to improve TFT characteristics, TS-SLS (Two-Shot Sequential Lateral Solidification) technology has been employed. A 1:6 demultiplexing scheme has been successfully implemented in the source driver owing to the superb characteristics of the TS-SLS TFTs, which resulted in small driver circuit area.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2009.08a
• /
• pp.250-250
• /
• 2009

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.1080-1082
• /
• 2008

An ultra-thin reflective flexible LCD film has been demonstrated. The 30% thickness of the display can be reduced by applying a quarter-wave-plate film as upper substrate. A low temperature alignment material and special designed photo spacer were applied in this new display. The bending behavior was improved by reduced thickness.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.1243-1246
• /
• 2006

A new source follower circuit for the integrated circuit of AMLCDs is proposed. Active load is added and calibration operation is applied to compensate the circuits. Proposed circuit is capable of minimizing the variation from both timing and device variations through measured results, the uniformity and bias effect are discussed.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.1046-1049
• /
• 2005

We have developed polymer LED displays using ink jet printing without visible swathe marks which can be observed during display operation. In addition, we have also developed a single-pass printing technology for hole-conduction layer deposition to significantly reduce the complexity of interlacing printing across the panel which is known as an alternative to remove the swathe mark.