Transition metal dichalcogenides (TMDs) with a two-dimensional layered structure have been considered highly promising materials for next-generation flexible, wearable, stretchable and transparent devices due to their unique physical, electrical and optical properties. Recent studies on TMD devices have focused on developing a suitable doping technique because precise control of the threshold voltage ($V_{TH}$) and the number of tightly-bound trions are required to achieve high performance electronic and optoelectronic devices, respectively. In particular, it is critical to develop an ultra-low level doping technique for the proper design and optimization of TMD-based devices because high level doping (about $10^{12}cm^{-2}$) causes TMD to act as a near-metallic layer. However, it is difficult to apply an ion implantation technique to TMD materials due to crystal damage that occurs during the implantation process. Although safe doping techniques have recently been developed, most of the previous TMD doping techniques presented very high doping levels of ${\sim}10^{12}cm^{-2}$. Recently, low-level n- and p-doping of TMD materials was achieved using cesium carbonate ($Cs_2CO_3$), octadecyltrichlorosilane (OTS), and M-DNA, but further studies are needed to reduce the doping level down to an intrinsic level. Here, we propose a novel DNA-based doping method on $MoS_2$ and $WSe_2$ films, which enables ultra-low n- and p-doping control and allows for proper adjustments in device performance. This is achieved by selecting and/or combining different types of divalent metal and trivalent lanthanide (Ln) ions on DNA nanostructures. The available n-doping range (${\Delta}n$) on the $MoS_2$ by Ln-DNA (DNA functionalized by trivalent Ln ions) is between $6{\times}10^9cm^{-2}$ and $2.6{\times}10^{10}cm^{-2}$, which is even lower than that provided by pristine DNA (${\sim}6.4{\times}10^{10}cm^{-2}$). The p-doping change (${\Delta}p$) on $WSe_2$ by Ln-DNA is adjusted between $-1.0{\times}10^{10}cm^{-2}$ and $-2.4{\times}10^{10}cm^{-2}$. In the case of Co-DNA (DNA functionalized by both divalent metal and trivalent Ln ions) doping where $Eu^{3+}$ or $Gd^{3+}$ ions were incorporated, a light p-doping phenomenon is observed on $MoS_2$ and $WSe_2$ (respectively, negative ${\Delta}n$ below $-9{\times}10^9cm^{-2}$ and positive ${\Delta}p$ above $1.4{\times}10^{10}cm^{-2}$) because the added $Cu^{2+}$ ions probably reduce the strength of negative charges in Ln-DNA. However, a light n-doping phenomenon (positive ${\Delta}n$ above $10^{10}cm^{-2}$ and negative ${\Delta}p$ below $-1.1{\times}10^{10}cm^{-2}$) occurs in the TMD devices doped by Co-DNA with $Tb^{3+}$ or $Er^{3+}$ ions. A significant (factor of ~5) increase in field-effect mobility is also observed on the $MoS_2$ and $WSe_2$ devices, which are, respectively, doped by $Tb^{3+}$-based Co-DNA (n-doping) and $Gd^{3+}$-based Co-DNA (p-doping), due to the reduction of effective electron and hole barrier heights after the doping. In terms of optoelectronic device performance (photoresponsivity and detectivity), the $Tb^{3+}$ or $Er^{3+}$-Co-DNA (n-doping) and the $Eu^{3+}$ or $Gd^{3+}$-Co-DNA (p-doping) improve the $MoS_2$ and $WSe_2$ photodetectors, respectively.
충남 부여군 홍산면 일대의 백운사층 셰일에서 산출되는 운모류 광물(혼합상 백운모)과 십자석에 대한 EPMA 연구를 수행하여, 혼합상 백운모와 십자석 생성 과정과의 관계 및 백운사층 셰일의 변성환경을 규명하고자 하였다. 암석에서 산출되는 운모류 광물의 평균 화학조성은 $(K_{1.11}Na_{0.26}Ca_{0.04})(Al_{3.93}Fe_{0.21}Mg_{0.07})(Si_{6.08}Al_{1.92})O_{20}(OH)_4$로 층간 양이온 함량이 낮으며(1.41) 팔면체 자리에 Fe, Mg를 함유한 일라이트, 즉 백운모/파이로필라이트/녹니석 혼합상($Mu_{70.5}Py_{23.5}Ch_{6.0}$)의 화학조성을 보인다. 한편 십자석은 암석 내에서 혼합상 백운모, 단일 결정의 파이로필라이트 및 알루미늄 규산염 광물과 함께 산출되는데, 이들 중 파이로필라이트가 십자석 생성에 참여한 것으로 판단된다. 혼합상 백운모에서 분리된 파이로필라이트와 녹니석이 반응하여 클로리토이드를 형성한 이후, 변성도가 증가하면서 파이로필라이트와 클로리토이드가 반응하여 십자석이 생성된 것으로 보이며, 이때 클로리토이드는 모두 소모되어 암석 내에서 관찰되지 않는 것으로 판단된다. 결국 일라이트가 백운모로 전이되는 과정에서 형성되는 혼합상 백운모는 십자석 생성에 필요한 광물을 공급하는 중요한 역할을 하는 것으로 보인다. 이 반응이 $300^{\circ}C$ 이상에서 일어나는 점과 혼합상 백운모에서 분리된 파이로필라이트가 약 $350^{\circ}C$에서 알루미늄 규산염 광물로 전이되는 점을 감안할 때, 백운사층 셰일은 $300{\sim}350^{\circ}C$의 변성환경을 경험한 것으로 판단된다.
The plasma damage free and room temperature processedthin film deposition technology is essential for realization of various next generation organic microelectronic devices such as flexible AMOLED display, flexible OLED lighting, and organic photovoltaic cells because characteristics of fragile organic materials in the plasma process and low glass transition temperatures (Tg) of polymer substrate. In case of directly deposition of metal oxide thin films (including transparent conductive oxide (TCO) and amorphous oxide semiconductor (AOS)) on the organic layers, plasma damages against to the organic materials is fatal. This damage is believed to be originated mainly from high energy energetic particles during the sputtering process such as negative oxygen ions, reflected neutrals by reflection of plasma background gas at the target surface, sputtered atoms, bulk plasma ions, and secondary electrons. To solve this problem, we developed the NBAS (Neutral Beam Assisted Sputtering) process as a plasma damage free and room temperature processed sputtering technology. As a result, electro-optical properties of NBAS processed ITO thin film showed resistivity of $4.0{\times}10^{-4}{\Omega}{\cdot}m$ and high transmittance (>90% at 550 nm) with nano- crystalline structure at room temperature process. Furthermore, in the experiment result of directly deposition of TCO top anode on the inverted structure OLED cell, it is verified that NBAS TCO deposition process does not damages to the underlying organic layers. In case of deposition of transparent conductive oxide (TCO) thin film on the plastic polymer substrate, the room temperature processed sputtering coating of high quality TCO thin film is required. During the sputtering process with higher density plasma, the energetic particles contribute self supplying of activation & crystallization energy without any additional heating and post-annealing and forminga high quality TCO thin film. However, negative oxygen ions which generated from sputteringtarget surface by electron attachment are accelerated to high energy by induced cathode self-bias. Thus the high energy negative oxygen ions can lead to critical physical bombardment damages to forming oxide thin film and this effect does not recover in room temperature process without post thermal annealing. To salve the inherent limitation of plasma sputtering, we have been developed the Magnetic Field Shielded Sputtering (MFSS) process as the high quality oxide thin film deposition process at room temperature. The MFSS process is effectively eliminate or suppress the negative oxygen ions bombardment damage by the plasma limiter which composed permanent magnet array. As a result, electro-optical properties of MFSS processed ITO thin film (resistivity $3.9{\times}10^{-4}{\Omega}{\cdot}cm$, transmittance 95% at 550 nm) have approachedthose of a high temperature DC magnetron sputtering (DMS) ITO thin film were. Also, AOS (a-IGZO) TFTs fabricated by MFSS process without higher temperature post annealing showed very comparable electrical performance with those by DMS process with $400^{\circ}C$ post annealing. They are important to note that the bombardment of a negative oxygen ion which is accelerated by dc self-bias during rf sputtering could degrade the electrical performance of ITO electrodes and a-IGZO TFTs. Finally, we found that reduction of damage from the high energy negative oxygen ions bombardment drives improvement of crystalline structure in the ITO thin film and suppression of the sub-gab states in a-IGZO semiconductor thin film. For realization of organic flexible electronic devices based on plastic substrates, gas barrier coatings are required to prevent the permeation of water and oxygen because organic materials are highly susceptible to water and oxygen. In particular, high efficiency flexible AMOLEDs needs an extremely low water vapor transition rate (WVTR) of $1{\times}10^{-6}gm^{-2}day^{-1}$. The key factor in high quality inorganic gas barrier formation for achieving the very low WVTR required (under ${\sim}10^{-6}gm^{-2}day^{-1}$) is the suppression of nano-sized defect sites and gas diffusion pathways among the grain boundaries. For formation of high quality single inorganic gas barrier layer, we developed high density nano-structured Al2O3 single gas barrier layer usinga NBAS process. The NBAS process can continuously change crystalline structures from an amorphous phase to a nano- crystalline phase with various grain sizes in a single inorganic thin film. As a result, the water vapor transmission rates (WVTR) of the NBAS processed $Al_2O_3$ gas barrier film have improved order of magnitude compared with that of conventional $Al_2O_3$ layers made by the RF magnetron sputteringprocess under the same sputtering conditions; the WVTR of the NBAS processed $Al_2O_3$ gas barrier film was about $5{\times}10^{-6}g/m^2/day$ by just single layer.
애씨디싸이오바실러스 페로악시댄스(Acidithiobacillus ferrooxidans; Af)에 의한 황철석의 산화 기작을 이해하기 위해 황철석-용액간 접종 배취실험 (batch experiment)을 수행하고, 주기적으로 용액의 화학 조성과 함께 반응 황철석의 표면을 주사전자현미경 (scanning electron microscope; SEM)으로 관찰하였다. 반응 용액의 Fe 농도 분석 결과는 Af가 뚜렷이 구분되는 성장 적응기와 증식기를 거침을 나타내었다. Af 성장 적응기 동안에 황철석 표변에 부착된 개체가 관찰됨으로써 이 기간 동안의 황철석이 Af에 의해 직접용탈 산화됨이 확인되었다. 하지만 부착된 개체가 많이 발견되지 않는 점과 Fe가 주로 Fe(III)로 존재한다는 점 등으로 인해 적응기간 동안 Af가 황철석을 주로 직접용탈을 통해 용해 시켰다고 확신하기는 어렵다. Af 성장 적응기의 중반 이후부터 증식기 직전까지 Fe 함량이 크기 증가 하지 않고 정체되는데, 이는 이 시기에 Af에 의한 황철석의 산화가 직접 또는 간접 용탈식 산화든, Af가 산화 기작의 전환을 위해 적응 기간을 분명히 필요로 하는 것으로 보인다. SEM 관찰 결과 황철석의 표면에서 Af의 세포 분열이 관찰되었다. 이 세포분열 외형을 따라 황철식이 그대로 용식된 모습을 보여주는데, 이는 Af에 의한 산화 속도가 매우 불균등하며 산화가 진행되는 동안에는 농도의 변화로 부터 계산되는 속도보다 훨씬 빠르게 진행됨을 나타낸다. Af의 접종이 이루어진 황철석의 표면에 훨씬 많은 부식홈이 관찰되어 이 미생물에 의한 산화가 무기적인 산화보다 훨씬 빨리 진행됨을 지시한다. Af에 의한 부식 홈은 좁고 깊어, 이것이 적응기-증식기 전이에 영향을 끼쳤을 가능성이 있다.
비산재 혼합에 의한 $CH_4$과 $CO_2$ 방출 저감 가능성을 조사하기 위해 질소 ($(NH_4)_2SO_4$) 무처리구와 처리구를 두고 비산재를 0, 5, 10% 수준으로 혼합한 후 토양 수분 변동조건 (습윤기간, 전이기간, 건조기간)에서 60일간 실험실내 항온배양실험을 통해 $CH_4$과 $CO_2$ flux를 분석하였다. 전체 항온배양기간 중 평균 $CH_4$ flux는 $0.59{\sim}1.68mg\;CH_4\;m^{-2}day^{-1}$의 범위였으며, 질소 무처리구에 비해 처리구에서 flux가 낮았는데, 이는 질소 처리시 함께 시용된 $SO_4^{2-}$의 전자수용체 기능에 의해 $CH_4$ 생성이 억제되었기 때문으로 판단되었다. 질소 무처리구와 처리구에서 비산재 10% 처리에 의해 $CH_4$ flux가 각각 37.5%와 33.0% 감소하였는데, 이는 물리적인 측면에서 미립질 (실트 함량 75.4%)인 비산재 시용에 의해 통기성 대공극량이 감소되어 $CH_4$ 확산 속도가 저감되었기 때문으로 판단되었다. 또한, 생화학적 측면에서는 비산재의 $CO_2$ 흡착능에 의해 $CH_4$ 생성의 주요 기작 중 하나인 이산화탄소 환원에 필요한 $CO_2$ 공급이 억제된 것도 원인 일 수 있다. 한편, 전체 항온 배양 기간의 평균 $CO_2$ flux ($0.64{\sim}0.90g\;CO_2\;m^{-2}day^{-1}$) 역시 질소 무처리구가 질소 처리구보다 높았다. 이는 일반적으로 질소 시비에 의해 토양 호흡량이 증가한다는 기존의 연구결과와는 상이한데, 본 연구에서 질소 처리에 의해 활성화된 미생물에 의해 $CO_2$ flux 최초 측정 시점 (처리 후 2일째) 이전에 이미 상당한 양의 $CO_2$가 이미 방출되어 실측 flux에 반영되지 못했기 때문으로 설명이 가능했다. $CH_4$과 유사하게 $CO_2$ flux도 비산재무처리구에 비해 비산재 10% 처리구에서 약 20% 감소하였는데, 이는 비산재의 원소 구성 중 Ca과 Mg과 토양수내 탄산이온의 탄산염 ($CaCO_3$과 $MgCO_3$)화 반응에 의한 $CO_2$ 침전 때문이다. 이상과 같은 비산재 처리에 의한 $CH_4$과 $CO_2$ flux 감소에 의해 지구온난화지수 역시 비산재 10% 처리구에서 약 20% 감소하였다. 따라서, 비산재는 논 토양에서 $CH_4$과 $CO_2$ 방출 저감에 효과가 있는 것으로 나타났으며, 실재 벼 재배 포장에서의 실험을 통한 추가적인 검증이 필요하다.
지난 10년 동안 유전체 내부에 형성된 나노미터 크기의 규소알갱이는 발광센터로서 주목 받아왔다 나노미터 크기인 결정질 규소의 엑시토닉 전자-홀의 쌍들이 발광결합에 기여한다고 여겨진다. 그러나 규소결정에 존재하는 여러가지 결함들은 비발광 천이의 경로가 되어 나노규소결접립의 발광천이와 경쟁하여 발광효율을 저하시키는 요인이 된다. 이러한 결정 결함들은 고온 열처리과정에서 대부분 소멸되나 $1000^{\circ}C$ 이상의 공정 에서도 나노규소와 유전체의 계면에 존재하는 결함들은 나노규소결정립의 발광을 억제하게 된다. 일반적으로 수소로서 규소결정립의 계면을 마감처리하게 되면 규소결정립의 발광효율이 획기적으로 향상되나 불행하게도 매질 내 수소의 높은 이동성으로 말미암아 후속 열처 리 과정에서 수소마감효과는 쉽게 손실된다. 따라서 본 연구에서는 온도가역적인 수소 대신 인을 이온주입 방법으로 첨가하여 수소와 같은 계면 마감효과를 얻으며 또한 후속 고온공정 에 대한 내구력을 증대시켰다. 모재인 산화규소 기판에 400keV, $1\times10^{17}\; Si/cm^2$와 그 주위에 균일한 함량을 도핑하기 위하여 다중에너지의 인을 주입하였다. 규소와 인을 이온주입 후 Ar 분위기에서 $1100^{\circ}C$ , 두 시간의 후열처리를 통하여 규소결정립을 형성하였으며 향상된 내열효과를 시험하기 위하여 Ar 분위기에서 $1000^{\circ}C$까지 열처리하였다. 인으로 마감된 나노미터 크기인 규소 결정립의 향상된 광-발광(PL)효과와 감쇄시간, 그리고 발광파장의 변화에 대하여 논의하였다.
진공증착법으로 $Cd_2GeSe_4$와 $Cd_2GeSe_4:Co^{2+}$ 박막을 ITO(indium tin oxide) 유리 기판 위에 제작하였다. 결정화는 증착된 박막들을 질소분위기의 전기로에서 열처리함으로서 이룰 수 있었다. X-선 회절 분석에 의하여 증착된 $Cd_2GeSe_4$와 $Cd_2GeSe_4:Co^{2+}$ 박막의 격자상수는 $a\;=\;7.405\;{\AA}$, $c\;=\;36.240\;{\AA}$와 $a\;=\;7.43\;{\AA}$, $c\;=\;36.81\;{\AA}$로서 능면체(rhombohedral) 구조이었고, 열처리 온도를 증가함에 따라 (113)방향으로 선택적으로 성장됨을 알 수 있었다. 열처리 온도를 증가시킴에 따라 입계 크기가 점차 커지고 판상구조로 결정화 되었다. 실온에서 측정한 광학적인 에너지 띠 간격은 열처리 온도의 증가에 따라 $Cd_2GeSe_4$ 박막의 경우 1.70 eV ~ 1.74 eV로 증가하였고, $Cd_2GeSe_4:Co^{2+}$ 박막의 경우 1.79 eV ~ 1.74 eV로 감소하였다. $Cd_2GeSe_4$와 $Cd_2GeSe_4:Co^{2+}$ 박막 내의 전하운반자들의 동역학적 거동을 광유기 방전 특성(PIDC : photoinduced discharge characteristics) 방법으로 조사하였다.
미국의 샌디에고광산에서 산출되는 분홍색이나 무색의 전기석과 산지가 알려지지 않은 브라질산의 청색 내지 녹색을 띄는 전기석 그리고 국내의 학산, 운천 광산에서 산출되는 흑갈색 전기석들의 화학적 성분과 광물 흡수 분광학적 특성을 연구하기 위하여 X선 회절기, 전자 현미 분석기, 광학적 흡수 분광분석 및 열 처리 실험 등을 이용하였다. 최소 자승법을 활용하여 단위포 크기를 구하면, 흑갈색 전기석 경우 a = 15.96-16.01 ${\AA}$, c = 7.15-7.16 ${\AA}$이며, 분홍색 전기석은 a = 15.82 - 15.87 ${\AA}, c = 7.09 - 7.10 ${\AA}$이며, 청색/녹색 전기석은 a = 15.88 - 15.94 ${\AA}$, c = 7.12 - 7.15 ${\AA}$이다. 전기석 광물들이 여러가지 다양한 색을 띄는 주요한 원인은 전이 원소들에 의한 것이다. 분홍색은 망간 3가, 청색 내지 녹색은 철 2가와 망간 2가, 청녹색은 구리 2가, 흑갈색은 철 2가, 철 2가 - 철 3가, 그리고 철 2가 - 티타늄 4가에 의해 색을 띄게 된다. 분홍색 전기석 경우, 망간 3가는 압축된 Y자리에서 O(1)H-O(3)H 축을 따라 쟌-텔러 변형으로 안정한 구조를 가지게 된다. 전기석 광물들을 고온으로 열처리하면, 일반적으로 분홍색 혹은 빨간색을 띄는 전기석들은 무색으로 변색이 되며, 청녹색은 녹청색으로 색상이 변하며, 황녹색 같은 경우는 일부 샘플들만 옅은 녹색으로 바뀌는 모습이 관찰되었다. 엘바이트-흑전기석 계에서는 철과 망간의 함량에 따라 색의 누대구조가 나타난다. 녹색 영역에서는 철의 함량이 높으며 분홍색 영역에서는 망간의 함량이 높다. 망간은 황색이나 무색 영역에서 보다 짙은 황색 영역에서 증가한다.났다.억제물질로 작용할 때 $K_i$값과 억제양상이 측정되었는데 모두 경쟁적 방해를 보였다. $K_i$값은 10mM 인산완충용액에서 측정한 것이 100 mM 인산완충용액에서 측정한 것보다 훨씬 낮아 인산기가 기질이 아니어도 효소의 부착에 큰 영향을 미치는 것을 보여주고 있다.
이 연구에서는 서울 석촌동 고분군 연접적석총에서 출토된 기와의 물리적 및 광물학적 특성을 바탕으로 소성온도를 추정하고, 열변형 과정을 해석하였다. 석촌동 고분군에서는 다량의 기와가 출토되었는데, 일부 기와는 열에 의해 형태가 변하고 불균일한 소성상태를 나타냈다. 원형기와의 표면과 속심의 색조는 비교적 균일한 황갈색 계열로서 약 12% 이상의 높은 흡수율을 나타내며, 미정질 기질에 세립질 석영, 장석류, 운모, 각섬석 등을 포함한다. 또한 미세조직 관찰 결과, 느슨한 기질과 운모의 층상구조가 확인되어 900℃ 이하의 산화환경에서 제작되었을 것으로 추정된다. 반면 열에 변형된 기와는 주로 적갈색과 청회색의 불균일한 표면 색조를 보이며, 단면은 치밀한 적갈색 표면과 다공성의 자회색 내부기질이 함께 나타나는 샌드위치 구조를 나타낸다. 흡수율은 0.8~11%이며, 멀라이트, 헤르시나이트가 동정되어 소성온도가 1,000℃ 이상으로 추정된다. 일부 시료에서는 과소성에 의한 블로우팅 포어(bloating pore)가 관찰되었고, 1,200℃ 이상의 고온을 경험한 것으로 판단된다. 한편, 원형기와를 800~1,200℃ 사이에서 온도별로 재소성하여 물리적 및 광물학적 특성을 확인한 결과, 1,000℃ 부근에서 흡수율이 급격히 낮아지고 고온 광물이 생성되기 시작했다. 또한 점차 온도가 올라갈수록 기질이 부분 용융되고 재결정화되어 변형기와의 열변형 특성과 유사한 결과를 나타냈다. 따라서 석촌동 고분군 기와는 불균일한 소성상태와 1,000~1,200℃에 달하는 2차 고온을 경험하여 형태 변형, 광물 상전이 등의 열변형 특성이 발생하였고, 이는 백제시대 화장의례와 관계가 있는 것으로 생각된다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.