• Proceedings of the Materials Research Society of Korea Conference
• /
• 2012.05a
• /
• pp.92-92
• /
• 2012

Chalcopyrite-type Cu(In,Ga)Se2 (CIGS) is one of the most attractive compound semiconductor materials for thin film solar cells. Among various approaches to prepare the CIGS thin film, the powder process offers an extremely simple and materials-efficient method. Here, we present the mechano-chemical synthesis of CIGS compound powders and their use as an ink material for screen-printing. During the synthesis process, milling time and speed were varied in the range of 10~600 min and 100~300 rpm, respectively. Both phase evolution and powder characteristics were carefully monitored by X-ray diffraction (XRD) method, scanning electron microscope (SEM) observation, and particle size analysis by scanning mobility particle spectrometer (SMPS) and aerodynamic particle sizer (APS). We found the optimal milling condition as 200 rpm for 120 min but also found that a monolithic phase of CIGS powders without severe particle aggregation was difficult to be obtained by the mechano-chemical milling alone. Therefore, the optimized milling condition was combined with an adequate heat-treatment (300oC for 60 min) to provide the monolithic CIGS powder of a single phase with affordable particle characteristics for the preparation of CIGS thin film. The powder was used to prepare an ink for screen printing with which dense CIGS thin films were fabricated under the controlled selenization. The morphology and electrical properties of the thin films were analyzed by SEM images and hall measurement, respectively.

• Journal of Powder Materials
• /
• v.20 no.6
• /
• pp.432-438
• /
• 2013

In this study, analysis on the oxidation behavior was conducted by a series of high-temperature oxidation tests at both $800^{\circ}C$, $900^{\circ}C$ and 1000 in the air with sintered STS 316L. The weight gain of each oxidized specimen was measured, the oxidized surface morphologies and composition of oxidation layer were analyzed with Scanning Electron Microscope-Energy Dispersive x-ray Spectroscopy (SEM-EDS), finally, the phase change and composition of the oxidized specimen were shown by X-Ray Diffraction (XRD). As a result, the weight gain increased sharply at $1000^{\circ}C$ when oxidation test was conducted for 210 hours. Also, a plentiful of pores were observed in the surface oxidation layers at $900^{\circ}C$ for 210 hours. In addition, the following conclusions on oxidation behavior of sintered STS 316L can be obtained: $Cr_2O_3$ can be formed on pores by influxing oxygen through open-pores, $(Fe_{0.6}Cr_{0.4})_2O_3$ can be generated on the inner oxidation layer, and $Fe_2O_3$ was on the outer oxidation layer. Also, $NiFe_2O_4$ could be precipitated if the oxidation time was kept longer.

• Journal of Pharmaceutical Investigation
• /
• v.25 no.3
• /
• pp.193-204
• /
• 1995

In order to examine the effect of extrahepatic cholestasis induced by common bile duct ligation on the hepatic function, the pharmacokinetics of antipyrine and d-propranolol were investigated in rats. In addition, in an attempt to observe the degree of direct hepatic injury, light and electron microscopic observations and conventional pathologic test using serum were performed. Five days after common bile duct ligation, antipyrine(15 mg/kg) and d-propranolol(3 mg/kg) were intravenously administrated to the rats, respectively. The total clearances of antipyrine and d-propranolol were significantly(p<0.05) decreased. Because hepatic clearance of antipyrine poorly extracted by the liver and that of d-propranolol highly extracted by the liver are respectively dependent on the hepatic intrinsic clearance and the hepatic blood flow, it may be concluded that extrahepatic cholestasis following five days after common bile duct ligation decreased the hepatic intrinsic clearance and the hepatic blood flow. SGPT, SGOT, cholesterol, bilirubin(total bilirubin, direct bilirubin) and alkaline phosphatase were significantly increased(p<0.05). The proliferation of bile ducts was prominent, and degeneration and necrosis of hepatocytes were observed by light microscope. Also, ultrastructurally, bile canaliculi were containing the amorphous materials and losing microvilli, and SER and RER in hepatocytes were dilated and vacuolated.

• Applied Microscopy
• /
• v.36 no.4
• /
• pp.259-269
• /
• 2006

Hemocytes of the spider Araneus ventricosus were investigated with histochemistry, density analysis of percoll gradient, and fine structural examinations using transmission electron microscope. The hemocytes of this spider were classified into two major groups: granulocytes and non-granulocytes. The granular hemocytes were subdivided into three subtypes according to their histochemical properties which are eosinophilic granuloctes(EGs), basophilic granulocytes(BGs) and cyanocytes. The EGs, which have small granules within the cytoplasm comprise about 5% of the total henocytes. However the granules of BGs are larger than those of HGs. The cyanocytes were characterized to contain hemocyanin granules in their cytoplasm. On the other hand, the non-granulocytes were divided into three subtypes; hyaline leucocytes, oenocytoids, and molting homocytes. The hyaline leucocytes are the most abundant and the smallest hemocyte type in this spider. The oenocytoids that have $10{\sim}15{\mu}m$ in diameter are mostly found at the marginal region of the myocardium in the heart tube. The molting hemocytes, which only appeared during the molting period, contains plenty of glycogen particles in their cytoplasm.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.101-101
• /
• 2018

Quantitative measurement of chloride ion concentration has an important role in various fields of electrochemistry, medical science, biology, metallurgy, architecture, etc. Among them, its importance of architecture is ever-growing due to unexpected degradations of building structure. These situations are caused by corrosion of reinforced concrete (RC) structure of buildings. And chloride ions are the most powerful factors of RC structure corrosion. Therefore, precise inspection of chloride ion concentration must be required to increase the accuracy of durability monitoring. Multi-walled Carbon nanotubes (MWCNTs) have high chemical resistivity, large surface area and superior electrical property. Thus, it is suitable for the channels of electrical signals made by the sensor. Silver nanoparticles were added to giving the sensing property. CuBTC, one of the metal organic frameworks (MOFs), was employed as a material to improve the sensing property because of its hydrophilicity and high surface area to volume ratio. In this study, sensing element was synthesized by various chemical reaction procedures. At first, MWCNTs were functionalized with a mixture of sulfuric acid and nitric acid because of enhancement of solubility in solution and surface activation. And functionalized MWCNTs, silver nanoparticles, and CuBTC were synthesized on PTFE membrane, one by one. Electroless deposition process was performed to deposit the silver nanoparticles. CuBTC was produced by room temperature synthesis. Surface morphology and composition analysis were characterized by scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDS), respectively. X-ray photoelectron spectroscopy (XPS) was also performed to confirm the existence of sensing materials. The electrical properties of sensor were measured by semiconductor analyzer. The chloride ion sensing characteristics were confirmed with the variation of the resistance at 1 V.

• Journal of Bio-Environment Control
• /
• v.10 no.2
• /
• pp.106-110
• /
• 2001

In an effort to evaluate the economic value and durability of the expanded rice hull as substrates, changes in the physical and chemical properties of material and plant growth in that substrate were studied. Using and electron microscope, the structure of used and new expanded rice hull substrate was examined. Considerable decomposition was found in the substrate which had been used one to three times. Compactness and lowered porosity in the used substrates were probably caused by decomposition. The results of cation analysis showed the possible destruction of cell wall of rice hulls. Abundant $Ca^{2+}$ in the substrates used for two to three times also indicated the possibility of decomposition. In tomato yield comparison, 15.2% more yield of tomato fruit in a new substrates indicated the negative effects of decomposition of one-time used substrates. Yield decreased in the substrates used for three times. if perlite substrates is used for three years before renewal and the cost of the perlite renewal is counted. 65.3% saving in the cost will be realized with the use of an expanded rice hull substrate. Another positive effect of the expanded rice hull substrate is the decrease of environmental contamination.n.

• Korean journal of food and cookery science
• /
• v.17 no.4
• /
• pp.367-372
• /
• 2001

This study was conducted to investigate the effect of rheological and sensory characteristics of the low-calorie layer cake made by adding different levels of polydextrose as a fat substitute for shortening. As the substitution level of polydextrose increased, the specific gravity of the cake batter increased and the viscosity decreased. The microstructures of cake crumb observed by a scanning electron microscope showed the decreased number and size of air cells and fat particles by increasing fat substitution level. The texture profile analysis using rheometer showed significant differences among the samples according to the levels of polydextrose for shortening. The hardness. gumminess, cohesiveness and chewiness of the cake declined gradually by increasing polydextrose level, while the springiness increased. There were no significant differences in resilience. Among various sensory properties, the appearance, flavor, crumb texture and overall acceptance of the layer cake decreased by increasing polydextrose level, although the taste score increased by adding 25% of polydextrose for shortening. Taking these results together, adding 25% polydextrose for shortening suggested to be a good substitution level for the low-calorie layer cake.

• Journal of Hydrogen and New Energy
• /
• v.19 no.4
• /
• pp.305-312
• /
• 2008

ZnO/Zn redox cycle is the one of the promising thermochemical cycles for hydrogen production via water splitting with high temperature heat source like a concentrated solar energy. This paper reports the particle size effect of Zinc on water splitting behavior. Water splitting reaction experiments were carried out at isothermal conditions of 350 and 400$^{\circ}C$ in TGA (Thermo Gravimetric Analyzer) using four commercial Zinc powders (nano, <10 ${\mu}m$, <150 ${\mu}m$ and $150{\sim}600\;{\mu}m$ particle sizes). Before the experiments, average particle size of Zinc powders was analyzed by PSA (Particle Size Analysis). After the experiments, XRD (X-Ray Diffraction) and SEM (Scanning Electron Microscope) analyses were conducted on the samples. The experimental results showed that particle size had a effect on the conversion of Zinc to ZnO. Zinc conversion was increased, as the particle size decreased. Especially, the nano size particles were aggregated and the particle's morphology changed on the surface during hydrolysis reaction.

• The Journal of Advanced Prosthodontics
• /
• v.6 no.3
• /
• pp.151-156
• /
• 2014

PURPOSE. To investigate the microtensile bond strength between two all-ceramic systems; lithium disilicate glass ceramic and zirconia core ceramics bonded with their corresponding glass veneers. MATERIALS AND METHODS. Blocks of core ceramics (IPS e.max$^{(R)}$ Press and Lava$^{TM}$ Frame) were fabricated and veneered with their corresponding glass veneers. The bilayered blocks were cut into microbars; 8 mm in length and $1mm^2$ in cross-sectional area (n = 30/group). Additionally, monolithic microbars of these two veneers (IPS e.max$^{(R)}$ Ceram and LavaTM Ceram; n = 30/group) were also prepared. The obtained microbars were tested in tension until fracture, and the fracture surfaces of the microbars were examined with fluorescent black light and scanning electron microscope (SEM) to identify the mode of failure. One-way ANOVA and the Dunnett's T3 test were performed to determine significant differences of the mean microtensile bond strength at a significance level of 0.05. RESULTS. The mean microtensile bond strength of IPS e.max$^{(R)}$ Press/IPS e.max$^{(R)}$ Ceram ($43.40{\pm}5.51$ MPa) was significantly greater than that of Lava$^{TM}$ Frame/Lava$^{TM}$ Ceram ($31.71{\pm}7.03$ MPa)(P<.001). Fluorescent black light and SEM analysis showed that most of the tested microbars failed cohesively in the veneer layer. Furthermore, the bond strength of Lava$^{TM}$ Frame/Lava$^{TM}$ Ceram was comparable to the tensile strength of monolithic glass veneer of Lava$^{TM}$ Ceram, while the bond strength of bilayered IPS e.max$^{(R)}$ Press/IPS e.max$^{(R)}$ Ceram was significantly greater than tensile strength of monolithic IPS e.max$^{(R)}$ Ceram. CONCLUSION. Because fracture site occurred mostly in the glass veneer and most failures were away from the interfacial zone, microtensile bond test may not be a suitable test for bonding integrity. Fracture mechanics approach such as fracture toughness of the interface may be more appropriate to represent the bonding quality between two materials.

• Journal of Technologic Dentistry
• /
• v.38 no.3
• /
• pp.157-163
• /
• 2016

Purpose: It is to compare and evaluate the change of the wear rate and phase variation of the Zirconia before and after the sintering after the grinding by a high speed equipment manufactured for the Zirconia. Methods: The specimen of the sintered Zirconia was manufactured as size of $15mm{\times}15mm{\times}2mm$. The grinding has been applied to each of all pieces of each test groups for a minute fit for each condition at same speed of 50,000 rpm by a diamond bur at high speed handpiece with injection of the air and water. For the observation of the surface before and after the sintering of the each test piece, the cross section of it was observed as 100 magnification by a scanning electron microscope after it was coated by PT, and the diffraction analysis was performed by XDR to compare the crystal phase of the Zirconia. The average surface roughness value of all specimens were evaluated. The wear test was performed at room temperature by applying a load of 1kg for 120,000 cycles for the chewing period 6 months. Wear was analyzed for the enamel cusps by measurement of the vertical substance loss with a laser scanner. Conclusion: The phase variation from the tetragonal phase to the monoclinic phase was confirmed in the test group of the pre-sintered Zirconia after the grinding, and the value of the surface roughness and the wear rate was increased in experimental group.