• Journal of Welding and Joining
• /
• 제31권4호
• /
• pp.47-53
• /
• 2013

SCMH2 steel is widely used in the industrial members of car and tractor. This study focused on material properties and evaluation technology of the SCMH2 steel regarding the surface treatment followed by carburizing and nitriding, by means of impact test, hardness test. and fatigue test including HCF (high cycle fatigue) and VHCF (very high cycle fatigue). Drop weight impact tester (Instron, 9250 Hv) and Cantilever type rotating-bending fatigue tester (YRB200, 3150 rpm) were used to characterize the SCMH2 standard specimen before and after carburizing/nitriding. In order to understand those effects on fatigue characteristics and material properties, the fractured surfaces were carefully observed and analyzed by SEM (scanning electron microscope) and EDS (energy-dispersive X-ray spectroscopy).

• Steel and Composite Structures
• /
• 제17권6호
• /
• pp.825-834
• /
• 2014

This manuscript presents an experimental investigation on the effect of Multi-walled carbon nanotubes (MWCNTs) addition on the tensile, flexural and impact properties of woven Kevlar fabric reinforced epoxy composites. MWCNTs were dispersed in the epoxy resin by sonication technique and the samples were fabricated by hand layup laminating procedure. Scanning electron microscopy (SEM) was used to characterize the microstructure of produced samples. The effects of adding small amounts (${\leq}1%$) of MWCNT on the tensile, flexural and impact (Izod) behaviors of laminated composites were analyzed. Results revealed that MWCNTs enhanced the Young's modulus up to 20%, bending modulus up to 40%, and impact strength up to 45% in comparison with woven Kevlar fabric/epoxy composites. It was found that the maximum improvements in mechanical properties were happened for 0.5 wt.% MWCNT.

• 한국안전학회지
• /
• 제10권2호
• /
• pp.64-71
• /
• 1995

Tests were performed to evaluate the effect of thermal shock behavior on the mechanical properties of PC(poly-carbonate) and PET(polyethylene-terephthalate) with MBS(methylmethacrylate-butadiene-styrene) alloy. Five different material weight fraction for PC/PET were employed : 0/100, 25/75, 50/50, 75/25, and 100/0. Three different weight fraction of MBS were added to each PC/PET : 0, 3, and 9. Therefore fifteen different types of PC/PET/MBS were prepared using single screw extrude. and injection molding machine. One thermal shock cycle consisted of each one hour stay at -$40^{\circ}C$ chamber and $＋80^{\circ}C$ chamber without delay. Specimens were thermal shocked up to 20 and 40 cycles. Specific mechanical properities considered in this study include tensile, izod impact, and high rate Impact behaviors. In addition, the morphology of the fractured surface after Izod impact testing was investigated by the SEM (scanning electron microscope).

• 반도체디스플레이기술학회지
• /
• 제23권1호
• /
• pp.36-47
• /
• 2024

The purpose of this study is to identify the factors that impact the user's intention to accept technology when Introducing new information security systems for the workers of a semiconductor company. The findings of this study were as follows. First, the factors of a company's information security systems, namely reliability, expertise, availability, security, and economic efficiency, all significantly and positively impacted performance expectations. Second, the performance expectation of introducing information security systems for a company significantly and positively impacted the intention to accept technology. Third, the social impact of introducing information security systems for a company had a significant and positive impact on technology acceptance intention. Fourth, the facilitating conditions for introducing a company's information security systems significantly and positively impacted technology acceptance intention. Fifth, as for the moderating effect of innovation resistance, the moderating effect was significant in the paths of [performance expectation -> technology acceptance intention], [social impact -> technology acceptance intention], and [facilitating conditions -> technology acceptance intention]. The implication of this study is that the factors to be considered when introducing information security systems were provided to companies that are the actors of their proliferation, providing the base data to lay the foundation for introducing security technologies and their proliferation.

• Steel and Composite Structures
• /
• 제48권3호
• /
• pp.305-320
• /
• 2023

The mechanical properties of polymeric composites are degraded under elevated temperatures due to the effect of temperature on the mechanical behavior of the resin and resin fiber interfaces. In this study, the effect of temperature on the impact response of the carbon fiber reinforced plastics (CFRP) was investigated at low-velocity impact (LVI) using a drop-weight impact tester machine. All the composite plates were fabricated using a vacuum infusion process with a stacking sequence of [45/0_2/-45/90_2]s, and a thickness of 2.9 mm. A group of the specimens was exposed to an environment with a temperature cycling at the range of -30 ℃ to 65 ℃. In addition, three other groups of the specimens were aged at ambient (28 ℃), -30 ℃, and 65 ℃ for ten days. Then all the conditioned specimens were subjected to LVI at three energy levels of 10, 15, and 20 J. To assess the behavior of the damaged composite plates, the force-time, force-displacement, and energy-time diagrams were analyzed at all temperatures. Finally, radiography, optical microscopy, and scanning electron microscopy (SEM) were used to evaluate the effect of the temperature and damages at various impact levels. Based on the results, different energy levels have a similar effect on the LVI behavior of the samples at various temperatures. Delamination, matrix cracking, and fiber failure were the main damage modes. Compared to the samples tested at room temperature, the reduction of temperature to -30 ℃ enhanced the maximum impact force and flexural stiffness while decreasing the absorbed energy and the failure surface area. The temperature increasing to 65 ℃ increased the maximum impact force and flexural stiffness while decreasing the absorbed energy and the failure surface area. Applying 200 thermal cycles at the range of -30 ℃ to 65 ℃ led to the formation of fine cracks in the matrix while decreasing the absorbed energy. The maximum contact force is recorded under cyclic temperature as 5.95, 6.51 and 7.14 kN, under impact energy of 10, 15 and 20 J, respectively. As well as, the minimum contact force belongs to the room temperature condition and is reported as 3.93, 4.94 and 5.71 kN, under impact energy of 10, 15 and 20 J, respectively.

• Journal of Welding and Joining
• /
• 제27권3호
• /
• pp.73-79
• /
• 2009

This present paper investigated the mechanical properties and the microstructures of each penetration shapes classifying the conduction shape area and the keyhole shape area about electron beam welded 120(T)mm thick plated aluminum 5052 112H. As a result the penetration depth is increased linearly according to the output power, but the aspect ratio is decreased after the regular output power. In the conduction shape area, the Heat affected zone is observed relatively wider than the keyhole shape area. In the material front surface of the welded specimen, the width is decreased but the width in the material rear surface is increased. After the measuring the Micro Vikers Hardness, it showed almost similar hardness range in all parts, and after testing the tensile strength, the ultimate tensile strength is similar to the ultimate tensile strength of the base material in all the specimens, also the fracture point was generated in the base materials of all the samples. In the result of the impact test, impact absorbed energy of the Keyhole shape area is turned up very high, and also shown up the effect about four times of fracture toughness comparing the base material. In the last result of observing the fractographs, typical ductile fraction is shown in each weld metal, and in the basic material, the dimple fraction is shown. The weld metals are shown that there are no other developments of any new chemical compound during the fastness melting and solidification.

• 한국진공학회지
• /
• 제19권5호
• /
• pp.331-340
• /
• 2010

초고주파 다중 중공 음극 방전을 이용한 플라즈마 화학 기상 증착 장치를 3차원 수치 모델링하였다. 기본적인 방전 특성을 파악하기 위하여 알곤 플라즈마를 40 MHz, 100 V, 133.3 Pa (1 Torr)의 조건에 대해서 계산하였다. 6 mm 직경의 홀을 20 mm 간격으로 배열하였고 전극 간격은 10 mm를 가정하였다. 피크 플라즈마 밀도는 홀의 하부 중앙에서 $5{\times}10^{11}#/cm^3$ 였으며 전자 온도는 접지 상태로 가정한 기판과 챔버 벽면 주위에서 가장 높았다. 준안정 상태에 의한 2단 이온화 속도는 전자 충돌에 의한 직접 이온화보다 10배 가량 높았다. 수소에 대한 계산에서는 이온화 이외의 다양한 에너지 소모 경로가 있어서 방전의 국재화가 잘 이루어지지 않았다.

• Journal of Welding and Joining
• /
• 제31권6호
• /
• pp.50-57
• /
• 2013

Characterization of microstructures and cryogenic mechanical properties of electro beam (EB) welds between cast and forged Inconel 718 superalloys has been investigated. Optimal EBW condition was found in the beam current range of 36~39 mA with the constant travel speed of 12 mm/s and arc voltage of 120 kV for 10 mm-thick specimens. Electron beam current lower than 25 mA caused to occur the liquation microfissuring in cast-side heat affected zone (HAZ) of EB welds. The HAZ liquation microfissure was found on the liquated grain boundaries with resolidified ${\gamma}/Laves$ and ${\gamma}/NbC$ eutectic constituents. EBW produced welds showing a fine dendritic structure with relatively discrete Laves phase due to fast cooling rate. After post weld aging treatment, blocky Laves phase and formation of ${\gamma}^{\prime}+{\gamma}^{{\prime}{\prime}}$ strengtheners were observed. Presence of primary strengthener and coarse Laves particles in PWHT weld may cause to reduce micro-plastic zone ahead of a crack, leading to a significant decrease in Charpy impact toughness at $-196^{\circ}C$. Fracture initiation and propagation induced by Charpy impact testing were discussed in terms of the dislocation structures ahead of crack arisen from the fractured Laves phase.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2000년도 춘계종합학술대회
• /
• pp.451-454
• /
• 2000

임팩트이온화는 고전계하에서 고에너지를 지닌 캐리어간 산란으로써 전자전송해석에 필수적인 요소이다. 임팩트이온화율 계산은 풀밴드 E-k관계와 페르미의 황금법칙을 이용하였다. 본 연구에서는 풀밴드 Monte Carlo 시뮬레이션을 이용하여 온도 및 전계에 대한 Si 임팩트이온화계수를 조사하였다. 임팩트이온화 모델에 의해서 계산된 look의 임팩트이온화계수는 실험값과 잘 맞았다. 온도상승에 따른 임팩트이온화계수와 전자의 에너지는 포논산란의 emission 모드의 증가 때문에 감소함을 알 수 있었다. 임팩트이온화계수의 대수는 온도와 전계에 대한 선형함수로 fitting 되었다. 이 선형함수의 오차는 5%이내이다. 결과적으로 임팩트이온화계수의 대수는 선형적으로 온도와 전계에 의존함을 알 수 있었다.

• Composites Research
• /
• 제17권4호
• /
• pp.53-60
• /
• 2004

본 연구에서는 1차원 파동방정식을 적용한 낙추충격시험 시스템을 제작하여 CFRP 적층판의 충격흡수특성 및 충격 강도평가를 하였으며 그 결과가 유효함을 보였다. 충격흡수에너지에 대해서는 충격에너지가 대략 6.8J이상에서는 동일한 T300 섬유와 적층배향으로 구성된 직교이방성 시험편이 의사등방성(quasi-isotropic)보다 높게 나타났으나 T700 섬유의 경우에는 크게 차이가 나타나지 않았다. 또한 동일한 T300 섬유와 적층수로 구성된 시험편이 T700섬유로 된 시험편보다 높게 나타났으나 T700 섬유의 의사등방성 시험편의 경우에는 크게 차이가 나타나지 않았다. 초음파 C-스캐너를 이용하여 내부손상영역을 관찰하여 시험편의 손상면적과 흡수에너지의 상관관계를 평가하였다. 또한 저속충격손상으로 인한 파면을 파괴메카니즘을 규명하기 위해 주사전자현미경으로 관찰하였다.