• Journal of Powder Materials
• /
• v.25 no.4
• /
• pp.340-345
• /
• 2018

Additive manufacturing by electron beam melting is an affordable process for fabricating near net shaped parts of titanium and its alloys. 3D additive-manufactured parts have various kinds of voids, lack of fusion, etc., and they may affect crack initiation and propagation. Post process is necessary to eliminate or minimize these defects. Hot isostatic pressing (HIP) is the main method, which is expensive. The objective of this paper is to achieve an optimum and simple post heat treatment process without the HIP process. Various post heat treatments are conducted for the 3D-printed Ti-6Al-4V specimen below and above the beta transus temperature ($996^{\circ}C$). The as-fabricated EBM Ti-6Al-4V alloy has an ${\alpha}^{\prime}$-martensite structure and transforms into the ${\alpha}+{\beta}$ duplex phase during the post heat treatment. The fatigue strength of the as-fabricated specimen is 400 MPa. The post heat treatment at $1000^{\circ}C/30min/AC$ increases the fatigue strength to 420 MPa. By post heat treatment, the interior pore size and the pore volume fraction are reduced and this can increase the fatigue limit.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.632-638
• /
• 2002

Electron beam (EB) and Gas tungsten arc (TIG) welds were performed on 12.7 mm thick Ti-6Al-4V plate (ASTM Titanium Grade 5). Charpy-V toughness and hardness, as well as, microstructure of the welds and penetration from the macrostructure were studied. It appears that by EB welding rather smaller $\beta$-grains than with TIG welding can be obtained. Next to the fusion line the $\beta$-grain size in the HAZ was 50 ${\mu}{\textrm}{m}$l while in the weld metal it was 150 ${\mu}{\textrm}{m}$. Charpy-V toughness of the EB weld metal was equal or even better to that of base metal, which shows that the $\alpha$-martensite per se is not particularly brittle if only the grain size is fine enough. This is similar to behavior of low carbon martensite in steel. The grain size was studied with light optical and scanning electron (SEM) microscopes. Thus for products, for products which can be manufactured automatically with very narrow fit, the EB welding of Ti-6Al-4V appears to yield satisfactory toughness without any complex post weld heat treatment. ill this study as in earlier studies the TIG welds gave lower toughness than that of the base material due to the higher heat input and slower cooling as compared to EB welding.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.9
• /
• pp.1-10
• /
• 2002

We have done various treatments of indium tin oxide (ITO) surface for organic light-emitting diodes (OLEDs), and investigated the surface states by different surface treatments using atomic force microscopy (AFM) and Auger electron spectroscopy (AES). We have fabricated OLEDs deposited by ultra-high vacuum molecular beam deposition system and studied the characteristics of the OLEDs. We have observed the dramatical improvement of the performance of OLEDs fabricated on ITO substrates treated by $O_2$ plasma treatment reduces the carbon comtamination of ITO surfaces and increases the work function of ITO.

• Food Science and Preservation
• /
• v.23 no.1
• /
• pp.139-143
• /
• 2016

This study investigated the effect of electron beam (EB) treatment on the microbial reduction of dried laver (Porphyra tenera) and identified EB-resistant bacteria from the treated dried laver. After EB treatments of 4 kGy and 7 kGy, the numbers of total bacteria and EB-resistant bacteria were measured using tryptic soy agar and mannitol salt agar, respectively. The morphological and biochemical characteristics of each isolated EB-resistant bacteria were investigated and these bacteria were identified. Compared to the control ($1.5{\pm}0.2){\times}10^6CFU/g$, the total bacterial number was significantly decreased to ($5.4{\pm}0.5){\times}10^4CFU/g$ and ($1.1{\pm}0.6){\times}10^4CFU/g$ after EB treatments of 4 kGy and 7 kGy, respectively. With a higher EB dosage, the number of red colonies was almost same, whereas the number of yellow colonies was significantly decreased to ($3.3{\pm}1.2){\times}10^3CFU/g$ and 0 CFU/g for 4 kGy and 7 kGy, respectively. All red and yellow colonies were gram-positive cocci, catalase-positive, and resistant to 3% and 5% NaCl media. From the 16S rDNA sequence analysis, yellow and red colonies were identified as either Micrococcus flavus or M. luteus, with 99% similarity for the yellow colonies, and Deinococcus proteolyticus and D. piscis, with 99% and 97% similarity for the red colonies, respectively.

• Korean Journal of Food Science and Technology
• /
• v.29 no.4
• /
• pp.771-775
• /
• 1997

Treatment with electron beam irradiation was investigated for the elimination of Escherichia coli O157:H7 which has been linked to outbreaks of foodborne illness on undercooked and raw meat. Before treatment, the maximum populations were observed at 16 hr when E. coli O157:H7 was incubated in TSB at $37^{\circ}C$. Incubation at $4^{\circ}C$ did not influence survival and growth of the strain. The numbers of E. coli O157:H7 were present about $10^{7}\;CFU/mL$ in the log $(6\;hr\;at\;37^{\circ}C)$ and stationary phase $(16\;hr\;at\;37^{\circ}C)$ of cells, respectively. Freezing $(24\;hr\;at\;-18^{\circ})$ had a more marked lethal effect. The $D_{10}$ value at $-18^{\circ}C$ of E. coli O157:H7 contaminated in frozen beef was 0.45 kGy, and inactivation factor were $6.67{\sim}11.11$ at the radiation doses of $3{\sim}5\;kGy$. Therefore, electron beam irradiation was an effective method to eleminate of E. coli O157:H7.

• Journal of the Korean Ceramic Society
• /
• v.47 no.6
• /
• pp.618-622
• /
• 2010

Cost-effective purification methods of silicon were carried out in order to replace the conventional Siemens method for solar grade silicon. Firstly, acid leaching which is a hydrometallurgical process was preceded with grinded silicon powders of metallurgical grade (~99% purity) to remove metallic impurities. Then, plasma treatments were performed with the leached silicon powders of 99.94% purity by argon plasma at 30 kW power under atmospheric pressure. Plasma treatment was specifically efficient for removing Zr, Y, and P but not for Al and B. Another purification step by EB treatment was also studied for the 99.92% silicon lump which resulted in the fast removal of boron and aluminum. That means the two methods are effective alternative tools for removing the doping elements like boron and phosphor.

• Proceedings of the Korean Environmental Sciences Society Conference
• /
• 1998.10a
• /
• pp.1-1
• /
• 1998

Advanced (Chemical) oxidation processes (AOP) differ from most conventional ones in that hydroxyl radical(OH.) is considered to be the primary oxidant. Hydroxyl radicalcan react non-selectively with a great number of organic and inorganic chemicals. The typical rate constants of true hydroxyl radical reactions are in the range of between 109 to 1012 sec-1. Many processes are possible to generate hydroxyl radical. These include physical and chemical methods and their combinations. Physical means involves the use of high energy radiation such as gamma ray, electron beam, and acoustic wave. Under an applied high energy radiation, water molecules can be decomposed to yield hydroxyl radicals or aqueous electrons. Chemical means include the use of conventional oxidants such as hydrogen peroxide and ozone, two of the most efficient oxidants in the presence of promoter or catalyst. Hydrogen peroxide in the presence of a catalyst such as divalent iron ions can readily produce hydroxyl radicals. Ozone in the presence of specific chemical species such as OH- or hydrogen peroxide, can also generate hydroxyl radicals. Finally the combination of chemical and physical means can also yield hydroxyl radicals. Hydrogen peroxide in the presence of acoustic wave or ultra violet beam can generate hydroxyl radicals. The principles for hydroxyl radical generation will be discussed. Recent case studied of AOP for water treatment and other environmental of applications will be presented. These include the treatment of contaminated soils using electro-Fenton, lechate treatment with conventional Ponton, treatment of coal for sulfur removal using sonochemical and the treatment of groundwater with enhanced sonochemical processes.

• The Journal of Korean Society for Radiation Therapy
• /
• v.29 no.2
• /
• pp.65-73
• /
• 2017

Purpose: Machine Performance Check (MPC) is a self-checking software based on the Electronic Portal Imaging Device (EPID) to measure daily beam outputs without external installation. The purpose of this study is to verify the usefulness of MPC by comparing and correlating daily beam output of QA Beamchecker PLUS. Materials and Methods: Linear accelerator (Truebeam 2.5) was used to measure 10 energies which are composed of photon beams(6, 10, 15 MV and 6, 10 MV-FFF) and electron beams(6, 9, 12, 16 and 20 MeV). A total of 80 cycles of data was obtained by measuring beam output measurement before treatment over five months period. The Pearson correlation coefficient was used to evaluate the consistency of the beam output between the MPC and the QA Beamchecker PLUS. In this study, if the Pearson correlation coefficient is; (1) 0.8 or higher, the correlation is very strong (2) between 0.6 and 0.79, the correlation is strong (3) between 0.4 and 0.59, the correlation is moderate (4) between 0.2 and 0.39, the correlation is weak (5) lower than 0.2, the correlation is very weak. Results: Output variations observed between MPC and QA Beamchecker PLUS were within 2 % for photons and electrons. The beam outputs variations of MPC were $0.29{\pm}0.26%$ and $0.30{\pm}0.26%$ for photon and electron beams, respectively. QA Beamchecker PLUS beam outputs were $0.31{\pm}0.24%$ and $0.33{\pm}0.24%$ for photon and electron beams, respectively. The Pearson correlation coefficient between MPC and QA Beamchecker PLUS indicated that photon beams were very strong at 15 MV, and strong at 6 MV, 10 MV, 6 MV-FFF and 10 MV-FFF. For electron beams, the Pearson correlation coefficient were strong at 16 MeV and 20 MeV, moderate at 9 MeV and 12 MeV, and very weak at 6 MeV. Conclusion: MPC showed significantly strong correlation with QA Beamchecker PLUS when testing with photon beams and high-energy electron beams in the evaluation of daily beam output, but the correlation when testing with low-energy electron beams (6 MeV) appeared to be low. However, MPC and QA Beamchecker PLUS are considered to be suitable for checking daily beam output, as they performed within 2 % of beam output consistency during the observation. MPC which can perform faster than the conventional daily beam output measurement tool, is considered to be an effective method for users.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.262.1-262.1
• /
• 2014

Lipid peroxidation induces functional deterioration of cell membrane and induces cell death in extreme cases. These phenomena are known to be related generally to the change of physical properties of lipid membrane such as decreased lipid order or increased water penetration. Even though the electric property of lipid membrane is important, there has been no report about the change of electric properties after lipid peroxidation. Herein, we demonstrate the molecular energy band change in red blood cell membrane through peroxidation by air-based atmospheric pressure DBD plasma treatment. Ion-induced secondary electron emission coefficient (${\gamma}$ value) was measured by using home-made gamma-focused ion beam (${\gamma}$-FIB) system and electron energy band was calculated based on the quantum mechanical Auger neutralization theory. The oxidized lipids showed higher gamma values and lower electron work functions, which implies the change of surface charging or electrical conductance. This result suggests that modified electrical properties should play a role in cell signaling under oxidative stress.

• Journal of the Korean Ceramic Society
• /
• v.43 no.2 s.285
• /
• pp.85-91
• /
• 2006

Electron Beam Physical Vapor Deposition (EB-PVD) was applied to fabricate a thin film YSZ electrolyte with large area on the porous NiO-YSZ anode substrate. Microstructural and thermal stability of the as-deposited electrolyte film was investigated via SEM and XRD analysis. In order to obtain an optimized YSZ film with high stability, both temperature and surface roughness of substrate were varied. A structurally homogeneous YSZ film with large area of $12\times12\;cm^2$ and high thermal stability up to $900^{\circ}C$ was fabricated at the substrate temperature of $T_s/T_m$ higher than 0.4. The smoother surface was proved to give the better film quality. Precise control of heating and cooling rate of the anode substrate was necessary to obtain a very dense YSZ electrolyte with high thermal stability, which affords to survive after post heat treatment for fabrication a cathode layer on it as well as after long time operation of solid oxide fuel cell at high temperature.