• Journal of Radiation Industry
• /
• v.5 no.2
• /
• pp.131-135
• /
• 2011

In this study, we fabricated the HDPE and ${\alpha}-Al_2O_3$ composites with PE-g-MA as a function of the ${\alpha}-Al_2O_3$ nanopowder weight ratios. The electron beam irradiations on HDPE/${\alpha}-Al_2O_3$ composites were carried out over a range of absorbed doses from 20 to 200 kGy to make three-dimensional network structures. The mechanical properties were characterized using UTM for confirming the changes of the flexural strength and tensile strength. It was observed that the mechanical properties of HDPE were enhanced by the addition of ${\alpha}-Al_2O_3$. However, the strength of the 5 wt% ${\alpha}-Al_2O_3$ added composites decreased due to the nano-powder aggregation. The mechanical properties of composites were increased as increasing the electron beam irradiation up to 150 kGy. We believed that the electron beam irradiated HDPE/${\alpha}-Al_2O_3$ composites can be a good candidate for a variety of industrial applications.

• Journal of Radiation Industry
• /
• v.8 no.2
• /
• pp.71-76
• /
• 2014

Endocrine disrupting chemicals (EDCs) and potential EDCs are mostly man-made, found in various materials such as pesticides, additives or contaminants in food, and personal care products. The high energy ionizing radiation has the ability to remove the EDCs with a very high degree of reliability and in a clean and efficient manner. The ionizing radiation interacts with EDCs both directly and indirectly. Direct interaction takes place with EDCs and the structure of EDCs is destroyed or changed. During indirect interaction, radiolysis products of water result in the formation of highly reactive intermediates which then react with the target molecules, culminating in structural changes. To confirm the radiation reduction of EDCs in industrial sludge, a pilot scale experiment up to 50 kGy of electron beam (EB) was conducted with samples from the textile dyeing industries. The experimental result showed the over 90% of reduction of Nonylphenol (NP) and Di(2-ethylhexyl) phthalate (DEHP) at around 10 kGy of absorbed doses.

• Journal of Radiation Protection and Research
• /
• v.47 no.3
• /
• pp.152-157
• /
• 2022

Background: The hemi-body electron beam irradiation (HBIe^-) technique has been proposed for the treatment of mycosis fungoides. It spares healthy skin using an electron shield. However, shielding electrons is complicated owing to electron scattering effects. In this study, we developed a thimble-like head bolus shield that surrounds the patient's entire head to prevent irradiation of the head during HBIe^-. Materials and Methods: The feasibility of a thimble-like head bolus shield was evaluated using a simplified Geant4 Monte Carlo (MC) simulation. Subsequently, the head bolus was manufactured using a three-dimensional (3D) printed mold and Ecoflex 00-30 silicone. The fabricated head bolus was experimentally validated by measuring the dose to the Rando phantom using a metal-oxide-semiconductor field-effect transistor (MOSFET) detector with clinical configuration of HBIe^-. Results and Discussion: The thimble-like head bolus reduced the electron fluence by 2% compared with that without a shield in the MC simulations. In addition, an improvement in fluence degradation outside the head shield was observed. In the experimental validation using the inhouse-developed bolus shield, this head bolus reduced the electron dose to approximately 2.5% of the prescribed dose. Conclusion: A thimble-like head bolus shield for the HBIe^- technique was developed and validated in this study. This bolus effectively spares healthy skin without underdosage in the region of the target skin in HBIe^-.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.360-360
• /
• 2011

In this work, SUS310S used for valve plate assembly was electron beam (EB) welded to determine the influence of the parametric conditions on the characteristics of the weld and to minimize porosity and micro-fissures among others. The evolution in the weld geometry and microstructure was examined as a function of the process conditions such as beam current and focusing current under a constant welding speed and accelerating voltage. The integrity of the EB welds in SUS310S was examined for defects (e.g. cracking, porosity, etc.), adequate penetration depth, and tolerable weld width deviation for the various welding conditions. Optical microscopy (OM), x-ray photoelectron spectroscopy analysis (XPS), scanning electron microscopy (SEM) and 3D micro-computed tomography (Micro-CT) for the cross section analysis of the electron beam welded SUS310S were utilized. The tensile strength and hardness were analyzed for the mechanical properties of the EB weld. At the 6 kV accelerating voltage, it was determined that a satisfactory penetration depth and desirable weld width deviation requires a beam current of 30 mA and a focusing current of 0.687 A at the welding speed of 25 mm/sec.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.151.1-151.1
• /
• 2014

Wake field effect on the electron beam from the undulator chamber in PAL-XFEL is analyzed. The wake field takeover some energy from the electron beam which will increase the energy spread of the electron beam. This will cause the degradation of the radiation power in PAL-XFEL. To decrease the effect, the surface of the undulator vacuum chamber should be fabricated with 200 nm surface roughness and 5 nm oxidation layer. In this presentation, the numerical calculation of the wake will be shown. Simulation results of the radiation generation in PAL-XFEL also will be presented.

• Journal of Radiation Protection and Research
• /
• v.26 no.3
• /
• pp.333-335
• /
• 2001

The 2 GeV electron linac, the injector of the Pohang Light Source, was used as a photo-neutron source for radiation shielding research. The operational beam parameters are the nominal electron intensity of $0.5\;{\sim}5\;nC/sec$, the repetition rate of 10 Hz, and the beam pulse length of 1.0 nsec. One electron beam line was modified in order to install the target systems for producing pulsed photo-neutrons. The neutron spectrum and intensity were investigated by the time-of-flight technique. The reliable maximum energy of the measured neutrons was about 500 MeV. The number of neutrons above 20 MeV produced by one 1 GeV electron in a thick Pb target was about $6.45{\times}10^{-4}/sr$ at 90 degrees to the beam axis. The status of the photo-neutron source and the application research are presented.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.41 no.3
• /
• pp.71-75
• /
• 2009

Cotton waste is usually used for cultivating agaric mushroom after outdoor fermentation for a few months. Electron beam was used to break down the polymer chaims of cotton waste for increasing low molecular weight soluble sugars, which may enhance the agaric mushroom cultivation. By increasing electron beam radiation, alpha cellulose content of the cotton waste was decreased while beta cellulose content and hot water solubles were increased. Electron beam radiation over 240 kGy on cotton waste caused significant increase of mushroom yield without lowering mushroom quality.

• Journal of Radiation Industry
• /
• v.7 no.2_3
• /
• pp.167-170
• /
• 2013

Lignin can be a valuable natural chemical resource. Structurally, lignin is a three-dimensional polymer made up of condensed C-C bonds and some ether linkages, most of which are not readily degraded. In this study, lignin carbonization under various electron beam pretreatment conditions was characterized through a thermogravimetric analysis (TGA), X-ray diffraction (XRD) and Raman spectroscopy. Lignin stabilization was controlled by various doses of electron beam irradiation corresponding to 50, 100, 200, 500 and 1,000 kGy; the carbonization process was performed under a nitrogen gas atmosphere at $1000^{\circ}C$ for 1 h. The TGA results showed that a 1,000 kGy lignin dose increased the residue weight from 39.96% to 45.23%, compared to non-irradiated lignin. This observation is in agreement with the XRD and Raman spectroscopy results, in which the two theta degrees and the degree of crystallization were improved by increasing the electron beam irradiation.

• Polymer(Korea)
• /
• v.32 no.6
• /
• pp.598-602
• /
• 2008

In this study we prepared crosslinked separators with the improved thermal stability by irradiating a commercial polyethylene (PE) separator for lithium secondary battery with an electron beam, and the thermal and mechanical properties of the prepared separators were evaluated as a function of the absorption dose. The thermal shrinkage of electron beam irradiated separator was decreased with increasing absorption dose. As a result of the shutdown behavior using an AC impedance, it was observed that the irradiated separator had the better shutdown function than the unirradiated separator. The modulus of the irradiated separator was enhanced as the absorption dose was increased, while the tensile strength and the break elongation of the irradiated separator were decreased.

• Journal of the Korean Society of Radiology
• /
• v.15 no.1
• /
• pp.79-83
• /
• 2021

In radiation therapy, electron beam is often used in the treatment of superficial lesion. Accurate measurements are required because electron beam interacts with them in the beam path and affects dose measurements. However, no research has been conducted on electron beam quality assurance. in this study, PbO-based dosimeter was fabricated as a basic study for electron beam quality assurance. Thus, the reproducibility and linearity of the energy of 6, 9, and 12 MeV were analyzed to evaluate measurement accuracy and precision. Reproducibility measurements show RSD value of 1.024%, 1.019% and 0.890%, respectively, at 6, 9, and 12 MeV. linearity measurements show 0.9999 R2 at 6, 9, and 12 MeV altogether. Both evaluations show that the PbO dosimeter has very good measurement accuracy and precision with excellent results.