• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.6
• /
• pp.1051-1055
• /
• 2008

If ZnS receive electric energy, it can generate light. Thin film ELD has merits of excellent sight effect, solid state and easy fabrication but has problems of low emission density, high power loss and high operating voltage. Thin film deposited by electron beam evaporator has good uniformity of 6%. We fabricate excellent thin film ELD for solution of this problems. The thin film ELD made in this study has brightness of 650fL at yellow light and 350fL at green light.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.18 no.1
• /
• pp.47-58
• /
• 2000

Transmittances of SiO2 and ZrO2 thin films, made by the electron beam evaporation method, were measured with a spectrophotometer to be used in determining their optical constants and thicknesses in the envelop method. New color glass lenses with high transmittance, which now can be manufactured in the industry, was successfully designed by using these constants. Also the vacuum evaporator could be mechanically corrected with these constants as correction factors.

• Journal of the Korean Magnetics Society
• /
• v.7 no.4
• /
• pp.205-211
• /
• 1997

The magnetic properties change which was induced by addition of small amount of Ni into Cr underlayer in CoCrTa/ CrNi thin film deposited by electron beam evaporator was investigated. The additional Ni element was found to be beneficial for incease in the coercivity of the thin film deposited at the room temperature. The origin of coercivity increase was elucidated by crystal orientation and microstructure investigation using XRD and AFM respectively. It was found that the grain size were increased by Ni addition. The coercivity of the film with CrNi underlayer is lower than that of film with Cr underlayer when prepared with higher substrate temperature. This result may be originated with the increase in grain size. When film was deposited at 280 $^{\circ}C$ substrate temperature, Cr segregation in grain boundary is found to be the other factor for determining coercivity value.

• Journal of the Semiconductor & Display Technology
• /
• v.5 no.1 s.14
• /
• pp.51-55
• /
• 2006

MgO thin films were prepared through electron-beam deposition onto ITO-coated glass substrates in order to measure electrical, dielectric, and microstructural properties. Design of experiments was performed in this study with the aim to understanding of the effects of processing variables, e.g., substrate temperature and filament current of an e-beam evaporator statistically. Leakage currents, relative dielectric constants, and diffraction intensities of MgO thin films were analyzed statistically, following the analysis procedure provided in the design of experiments. The leakage current level of MgO thin films has been found to be statistically significant at the level of $\alpha=0.1$.

• The Journal of Korean Academy of Prosthodontics
• /
• v.29 no.2
• /
• pp.245-265
• /
• 1991

The purpose of this study was to observe the changes of the elemental transmission and bond strength between the metal and porcelain according to various kinds of ion beam mixing method. ion beam mixing of $meta1/SiO_2$ (silica), $meta1/Al_2O_3$(alumina) interfaces causes reactions when the $Ar^+$ was implanted into bilayer thin films using a 100KeV accelerator which was designed and constructed for this study. A vacuum evaporator used in the $10^{-5}-10^{-6}$ Torr vacuum states for the evaporation. For this study, three kinds of porcelain metal selected, -precious, semiprecious, and non-precious. Silica and alumina were deposited to the metal by the vacuum evaporator, separately. One group was treated by two kinds of dose of the ion beam mixing $(1\times10^{16}ions/cm^2,\;5\times10^{15}ions/cm^2)$, and the other group was not mixed, and analyzed the effects of ion beam mixing. The analyses of bond strength, elemental transmissions were performed by the electron spectroscopy of chemical analysis (ESCA), light and scanning electron microscope, scratch test, and micro Vickers hardness tests. The finding led to the following conclusions. 1. In the scanning electron and light microscopic views, ion beam mixed specimens showed the ion beam mixed indentation. 2. In the micro Vickers hardness and scratch tests, ion beam mixed specimens showed higher strength than that of non mixed specimens, however, nonprecious metal showed a little change in the bond strength between mixed and non mixed specimens. 3. In the scratch test, ion beam mixed specimens showed higher shear strength than that of non treated specimens at the precious and semiprecious groups. 4. In the ESCA analysis, Au-O and Au-Si compounds were formed and transmission of the Au peak was found ion beam mixed $SiO_2/Au$ specimen, simultaneously, in the higher and lower bonded areas, and ion beam mixed $SiO_2/Ni-Cr$ specimen, oxygen, that was transmitted from $SiO_2\;to\;SiO_2/Ni-Cr$ interface combined with 12% of Ni at the interface.

• Journal of the Korean Magnetics Society
• /
• v.9 no.4
• /
• pp.210-216
• /
• 1999

The objective of this paper is to investigate corrosion behaviors of CoCrTa/CrNi thin film and post heat-treatment effect. An electron beam evaporator was used for films deposition. After evaporation, post heat-treatment was carried out under $5.0{\times}10^3$ Torr vacuum condition. Annealing temperature and time were 400 $^{\circ}C$ and 30 min, respectively. To understand the effect of annealing on corrosion behavior of CoCrTa/CrNi, potentiodynamic polarization technique and accelerated corrosion chamber test were undertaken. Corrosion potential is higher for the annealed samples (CoCrTa 400$\AA$/CrNi 1000$\AA$) than for as-deposited one. This is attributed to an enrichment of Cr in the surface layer of the thinfilm resulting in a more corrosion resistant material.

• Korean Journal of Metals and Materials
• /
• v.46 no.10
• /
• pp.683-690
• /
• 2008

In order to develop transparent electrodes for high efficiency GaN-based light emitting diodes (LEDs), the electrical and optical properties of the electron beam evaporated ITO contacts have been investigated as a function of the deposition temperature and flow rate of oxygen during the deposition. As the deposition temperature increases from $140^{\circ}C$ to $220^{\circ}C$, the resistivity of the ITO films decreases slightly from $4.0{\times}10^{-4}{\Omega}cm$ to $3.3{\times}10^{-4}{\Omega}cm$, meanwhile the transmittance of the ITO films significantly increases from 67% to 88% at the wavelength of 470 nm. When the flow rate of oxygen during the deposition increases from 2 sccm to 4 sccm, the resistivity of the ITO films increases from $3.6{\times}10^{-4}{\Omega}cm$ to $7.4{\times}10^{-4}{\Omega}cm$, meanwhile the transmittance of the ITO films increases from 86% to 99% at 470 nm. Blue LEDs fabricated with the electron beam evaporated ITO electrode show that the ITO films deposited at $200^{\circ}C$ and 3 sccm of the oxygen flow rate give a low forward-bias voltage of 3.55 V at injection current of 20 mA with a highest output power.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2002.05a
• /
• pp.92-97
• /
• 2002

We establish a visible light emission from porous polycrystalline silicon nano structure(PPNS). The PPNS layer are formed on heavily doped n-type Si substrate. 2um thickness of undoped polycrystalline silicon deposited using LPCVD (Low Pressure Chemical Vapor Deposition) anodized in a HF: ethanol(=1:1) as functions of anodizing conditions. And then a PPNS layer thermally oxidized for 1 hr at $900 ^{\circ}C$. Subsequently, thin metal Au as a top electrode deposited onto the PPNS surface by E-beam evaporator and, in order to establish ohmic contact, an thermally evaporated Al was deposited on the back side of a Si-substrate. When the top electrode biased at +6V, the electron emission observed in a PPNS which caused by field-induces electron emission through the top metal. Among the PPNSs as functions of anodization conditions, the PPNS anodized at a current density of $10mA/cm^2$ for 20 sec has a lower turn-on voltage and a higher emission current. Furthermore, the behavior of electron emission is uniformly maintained.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.180-180
• /
• 2015

Solution processed Resistive random access memory (ReRAM)은 간단한 공정 과정, 고집적도, 저렴한 가격, 대면적화 플라즈마 데미지 최소화 등의 장점으로 차세대 비휘발성 메모리로 써 많은 관심을 받고 있으며, 주로 high-k 물질인 HfOx, TiOx, ZnO 가 이용 된다. IGZO와 ZTO와 같은 산화물 반도체는 높은 이동도, 대면적화, 넓은 밴드갭으로 인하여 투명한 장점으로 LCDs (Liquid crystal displays)에 이용 가능하며, 최근에는 IGZO와 ZTO에서 Resistive Switching (RS) 특성을 확인한 논문이 보고되면서 IGZO와 ZTO를 ReRAM의 switching medium와 TFT의 active material로써 동시에 활용하는 것에 많은 관심을 받고 있다. 이와 같은 산화물 반도체는 flat panel display 회로에 TFT와 ReRAM의 active layer로써 집적가능 하며 systems-on-panels (SOP)에 적용 가능하다. 하지만 IGZO 보다는 ZTO가 In과 Ga을 포함하지 않기 때문에 저렴하다. 그러므로 IGZO를 대신하는 물질로 ZTO가 각광 받고 있다. 본 실험에서는 ZTO film에 Al을 doping하여 메모리 특성을 평가하였다. 실험 방법으로는 p-type Si에 습식산화를 통하여 SiO2를 300 nm 성장시킨 기판을 사용하였다. 그리고 Electron beam evaporator를 이용하여 Ti를 10 nm, Pt를 100 nm 증착 한다. 용액은 Zn와 Tin의 비율을 1:1로 고정한 후 Al의 비율을 0, 0.1, 0.2의 비율로 용액을 각각 제작하였다. 이 용액을 이용하여 Pt 위에 spin coating방법을 이용하여 1000 rpm 10초, 6000 rpm 30초의 조건으로 AZTO (Al-ZnO-Tin-Oxide) 박막을 증착한 뒤, solvent 및 불순물 제거를 위하여 $250^{\circ}C$의 온도로 30분 동안 열처리를 진행하였다. 이후 Electron beam evaporator를 이용하여 top electrode인 Ti를 100 nm 증착하였다. 제작된 메모리의 전기적 특성은 HP 4156B semiconductor parameter analyzer를 이용하여 측정하였다. 측정 결과, AZTO (0:1:1, 0.1:1:1, 0.2:1:1)를 이용하여 제작한 ReRAM에서 RS특성을 얻었으며 104 s이상의 신뢰성 있는 data retention특성을 확인하였다. 그리고 Al의 비율이 증가할수록 on/off ratio가 증가하고 endurance 특성이 향상되는 것을 확인하였다. 결론적으로 Al을 doping함으로써 ZTO film의 메모리 특성을 향상 시켰으며 AZTO film을 메모리와 트랜지스터의 active layer로써 활용 가능할 것으로 기대된다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.5 no.1
• /
• pp.25-36
• /
• 1995

We have investigated the structure and the conductivity of the $Cd_{1-y}Zn_{y}$ Te films evaporated on the glass substrates (Corning 7059) by Electron Beam Evaporator (EBE) in pressure of approximately $1 {\times} 10^{-6}$ torr.The structure temperatures were held at both room temperature and $300^{\circ}C$, and the samples have annealed for an hour at $300^{\circ}C$ The survace com-position of the as-prepared films were slightly different from those of CdZn Te source material.Cd losses on the CdZnTe surface was measured about 4% of atomic ratio at room temperature substrate, whereas Zn atomic ratio was nearly constant, relatively. The strure is observed to be polycrystalline whose phase is mainly cubic phase. Thermal expansion coefficient was $6.30 {\times} 10^{-5}/^{\circ}C$ which was calculated from the variation of lattice parameter by X-ray powder pat-terns measured at $400^{\circ}C$.Diffraction peaks were slightly increased by annealing for an hour at $300^{\circ}C $, but they werey highly affected by substrate temperature during evaporation.