• Journal of Sensor Science and Technology
• /
• v.15 no.3
• /
• pp.168-172
• /
• 2006

Potentiometric $CO_{2}$ sensors were fabricated using a NASICON ($Na_{1+x}Zr_{2}Si_{X}P_{3-X}O_{12}$, 1.8 < x < 2.4) thick film and auxiliary layers. The powder of a precursor of NASICON with high purity was synthesized by a sol-gel method. By using the NASICON paste, an electrolyte was prepared on the alumina substrate by screen printing and then sintered at $1000^{\circ}C$ for 4 h. A series of $Na_{2}CO_{3}-CaCO_{3}$ auxiliary phases were deposited on the Pt sensing electrode. The electromotive force (emf) values were linearly dependent on the logarithm of $CO_{2}$ concentration in the range between 1,000 and 10,000 ppm. The device attached with $Na_{2}CO_{3}-CaCO_{3}$ (1:2 in mol.%) showed good sensing properties in the low temperatures.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.9
• /
• pp.1325-1333
• /
• 2017

The sensorless control of blushless DC motor(BLDCM) is based on the $120^{\circ}$ control in which the back electromotive force(Back EMF) for estimating the position of the rotor can be detected. However, the $120^{\circ}$ control has a disadvantage that the torque constant is small as compared with $180^{\circ}$ control which can not detect the back EMF. The $150^{\circ}$ control which complements these problems makes it possible to detect the back EMF and improve the torque constant by 12.5% compared to the $120^{\circ}$ control. Therefore, this paper compares the output characteristics of BLDCM through finite element method analysis (FEA) by the conventional and proposed control methods of BLDCM for water circulation system and proposes design for downsizing and weight reduction of BLDCM according to secured torque constant. The validity of the proposed control and design proposal is proved through simulation and experimental results by comparing the output characteristics of $120^{\circ}$ control and $150^{\circ}$ control.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.10
• /
• pp.60-67
• /
• 2006

This paper presents the temperature control in aluminum plate with Peltier module. From the experimental work, Peltier module is used to control the temperature of small aluminum plate for both heating and cooling with the control of current and fan ON/OFF. And current control of Peltier module was accomplished by PWM method. As a result of experiments, it is proper that operate cooling fan only while cooling duration and there exist a proper cooling current to drop temperature rapidly. It takes about 125sec to control temperature of aluminium plate between $30^{\circ}C$ and $70^{\circ}C$ and about 70sec between $40^{\circ}C$ and $60^{\circ}C$, in ambient temperature $28^{\circ}C{\sim}29^{\circ}C$ while cooling fan is operated only cooling duration. With the cooling current, temperature control of aluminum plate was accomplished more rapidly in comparison without cooling current. Future aim is to realize more rapid temperature control and develop SMHA(special metal hydride actuator) by using Peltier module as a heating and cooling source.

• Bulletin of the Korean Chemical Society
• /
• v.26 no.4
• /
• pp.548-552
• /
• 2005

The interaction between ionic surfactants and different nonionic molecules and polymers are studied using ion surfactant selective electrode. From the experimental data, critical concentrations of the interaction and binding process are evaluated. The interaction between hexadecyltrimethylammonium bromide (HTAB) with polyethylene glycol (PEG) in three molecular weights (1000, 10000 and 100000) and also schiff-bases, 2-[2-carboxyphenyl nitrilomethylidyne]-phenol (ortho CNP), 2-[3-carboxyphenyl nitrilomethylidyne]-phenol (meta CNP)and 2-[4-carboxyphenyl nitrilomethylidyne]-phenol (para CNP) with the potentiometric method were investigated using HTAB membrane selective electrode. In the case of PEG with increasing molecular weights more interaction to HTAB occurs. The electromotive force (EMF) data also showed that interaction between para CNP with HTAB is more than the other schiff-bases. It seems this case related to less space interference of COOH group for that compound. The onset of binding ($T_1$) of course is the same for three schiffbase molecules.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.26 no.1
• /
• pp.66-74
• /
• 2012

This paper propose a improved direct torque control(DTC) system for improving operation of five-phase squirrel-cage induction motor(IM). A five-phase IM drives present unique characteristics due to the additional degrees of freedom and also drives possess many others advantage compared with the traditional three-phase motor drive system, such as reducing a amplitude of torque pulsation and increasing the reliability. In order to maximize the torque per ampere, the proposed motor has concentrated windings and the produced back-electromotive force(EMF) is almost trapezoidal, and the motor is supplied with the combined sinusoidal plus third harmonic of currents, there is necessary to controlled 3rd harmonic current. Also a DTC method is advantageous when it is applied to the five-phase IM, because the five-phase inverter provides 32 space vectors in comparison to 8 space voltage vectors into the three-phase inverter drive system. For presenting the superior performance of the proposed DTC, experimental results of speed control are presented using a 32-bit fixed point TMS320F2812 DSP with 1.5[hp] IM.

• ETRI Journal
• /
• v.37 no.6
• /
• pp.1176-1187
• /
• 2015

This work proposes a highly efficient sensorless motor driver chip for various permanent-magnet synchronous motors (PMSMs) in a wide power range. The motor driver chip is composed of two important parts. The digital part is a sensorless controller consisting mainly of an angle estimation block and a speed control block. The analog part consists of a gate driver, which is able to sense the phase current of a motor. The sensorless algorithms adapted in this paper include a sliding mode observer (SMO) method that has high robust characteristics regarding parameter variations of PMSMs. Fabricated SMO chips detect back electromotive force signals. Furthermore, motor current-sensing blocks are included with a 10-bit successive approximation analog-to-digital converter and various gain current amplifiers for proper sensorless operations. Through a fabricated SMO chip, we were able to demonstrate rated powers of 32 W, 200 W, and 1,500 W.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.897-900
• /
• 2005

This paper presents temperature control of aluminum plate using Peltier module. As one of the thermoelectric effect, Peltier effect is heat pumping phenomena by electric energy. So if current is charged to Peltier module, it absorbs heat from low temperature side and emits heat to high temperature side. In this experiment, Peltier module is used to control the temperature of small aluminum plate with heating and cooling ability of Peltier module with current control and fan On/OFF control. And current control of Peltier module was accomplished by PWM method. As a results of experiments, it takes about 125sec to control temperature of aluminium plate between $30^{\circ}C\;and\;70^{\circ}C$ and about 70sec between $40^{\circ}C\;and\;60^{\circ}C$, in ambient temperature $29^{\circ}C$ while operating cooling fan only while cooling duration. Future aim is to realize more rapid temperature control and develop SMHA(special metal hydride actuator) by using Peltier module as a heating and cooling source.

• Proceedings of the KIPE Conference
• /
• 2019.07a
• /
• pp.374-375
• /
• 2019

In this paper, In the whole industry, there is a tendency to replace brushless motors with brushless motors because of the high rate of failure in DC motors with brushes. Accordingly, many methods for driving a brushless motor have been developed and studied. In order to drive the brushless motor, it is essential to know the information about the rotor position of the motor. However, it is not possible to use a position sensor for rotor disconnection due to the structure of an electric compressor brushless DC motor. In this paper, we investigate the rotor position of the motor by using the counter electromotive force included in the voltage of the terminal made by Y connection by using the resistance of each phase without using Hall sensor or encoder generally used to detect the rotor position. A sensorless drive system for a square wave brushless direct current (DC) motor is proposed. To do this, we propose a method to detect the rotor position from the analyzed terminal voltage waveform by performing terminal voltage analysis of each phase for 3-phase, 2-exciton unipolar PWM.

• Journal of the Korean institute of surface engineering
• /
• v.55 no.3
• /
• pp.156-163
• /
• 2022

An ammonium ion with a size and charge similar to that of potassium can bind to valinomycin, which is used as an ion carrier for potassium, and cause a meaningful interference effect on the detection of potassium ions. Currently, there are few ion sensors that correct the interference effect of ammonium ions, and there are few studies that specifically suggest the mechanism of the interference effect. By fabricating a SPCE-based potassium ion-selective electrode, the electromotive force was measured in the concentration range of potassium in the nutrient solution, and the linear range was measured to be 10^-5 to 10^-2 M, and the detection limit was 10^-5.19 M. And the interference phenomenon of the potassium sensor was investigated in the concentration range of ammonium ions present in the nutrient solution. Therefore, a data-based analysis strategy using deep learning was presented as a method to minimize the interference effect.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.3
• /
• pp.275-282
• /
• 2012

This paper presents a comparison of antenna factor characteristics computed by the Method of Moments(MoM) and the electromotive force(EMF) method for a calculable dipole antenna with a hybrid balun. An expression for the antenna factor is formulated using the concept of power mismatch loss. The input impedance and effective length of the antenna, which are in the formula of the antenna factor, are calculated using the two methods. The results show that the antenna factors are agreed within 0.24 dB, although the maximum difference between the input impedances obtained from the two methods is about 17 ${\Omega}$.