• Journal of the Korean Applied Science and Technology
• /
• v.21 no.2
• /
• pp.164-173
• /
• 2004

The capacity and long life of gel electrolyte batteries is connected with gas recombination producting $PbO_2$ and Pb electrode. We prepared with sulfuric acid gel electrolyte to know gel characteristics per density to assemble valve regulated lead-acid (VRLA) batteries. We studied on actions of sulphuric acid gel electrolyte by measuring electrolyte dispersion using Brewster-angle microscope (BAM), charge-discharge cycle, and electrode structure using scanning election microscope (SEM). Sulphuric acid density 1.210 showed excellent gel dispersion in sol condition, electrode condition after fifty cycles in this study.

• Journal of the Korean Ceramic Society
• /
• v.32 no.2
• /
• pp.189-196
• /
• 1995

Materials retaining electrolyte of a phosphoric acid fuel cell (PAFC) have been prepared with SiC powder to SiC whisker mixing ratios of 1:1, 1:2, 1:3, 1:4, 0:1 by a tape casting method. When 3wt% dispersant (sorbitan monooleate) is added to a matrix, the porosity of the matrix decreases a little while the bubble pressure and area of the matrix increase remarkably in comparison with no dispersant content. Effect of the electrolyte resistance and the polarization resistance on perfomance of a PAFC has been investigated using A.C. impedance spectroscopy. With the increase of whisker content, the electrolyte resistance decreases due to the increase of porosity and acid absorbancy, and the polarization resistance increases due to the increase of surface roughness. The polarization resistance affects current density predominantly at the higher potential than 0.7V becuase the polarization resistance is considrably larger than the electrolyte resistance. Both the electrolyte resistance and the polarization resistance affect current density near 0.7V of the fuel cell operating potential because they have similar values. The electrolyte resistance affects current density predominantly at the lower potential than the fuel cell operating potential because the electrolyte resistance is larger than the polarization resistance.

• Membrane and Water Treatment
• /
• v.11 no.3
• /
• pp.217-222
• /
• 2020

An electrochemical oxidation process was applied to remove cyanide (CN^-) from real plating wastewater. CN^- removal efficiencies were investigated under various operating factors: current density and electrolyte concentration. Electrolyte concentration positively affected the removal of both CN^- and Chemical Oxygen Demand (COD). As the electrolyte concentration increased from 302 to 2,077 mg Cl^-/L, removal efficiency of CN^- and COD increased from 49.07% to 98.30% and from 23.53% to 49.50%, respectively, at 10 mA/㎠. Current density affected the removal efficiency in a different way. As current density increased at a fixed electrolyte concentration, CN^- removal efficiency increased while COD removal efficiency decreased, this is probably due to lowered current efficiency caused by water electrolysis.

• Journal of the Korean Applied Science and Technology
• /
• v.20 no.4
• /
• pp.296-308
• /
• 2003

The capacity and long life of gel electrolyte batteries is connected with gas recombination producting $PbO_2$ and Pb electrode. We were prepared with phosphoric acid gel electrolyte to know gel characteristics per density to assemble VRLA batteries. We studied by measuring electrolyte dispersion using Brewster-angle microscope(BAM), charge-discharge cycle and electrode structure using scanning election microscope(SEM) per electrolyte density. As a results, phosphoric acid density 1.210 was excellent gel dispersion in sol condition, electrode condition after fifty cycles in this study.

• Transactions of the Korean hydrogen and new energy society
• /
• v.24 no.4
• /
• pp.347-352
• /
• 2013

Four types of electrolyte were tested for the application as an electrolyte in the Zn-Br redox flow battery. Electrolyte was consist of $ZnBr_2$ (electrolyte number 1), $ZnBr_2+KCl$ (electrolyte number 2), $ZnBr_2+KCl+NH_4Br$ (electrolyte number 3) and $ZnBr_2+KCl+EMPBr(C_7H_{16}BF_4N)$ (electrolyte number 4). The each electrolyte property was measured by CV (cyclic voltammetry) method. The different between the potential of anodic and cathodic maximum current density in a CV experiment (${\Delta}E_P$) was 0.89V, 0.89V, 1.06V and 0.61V for the electrolyte number 1, 2, 3 and 4, respectively. The electrolyte involved KCl increased conductivity which was appeared by anodic and cathodic maximum current density in a CV experiment. It was estimated that the electrolyte of number 3 ($ZnBr_2+KCl+NH_4Br$) and number 4 ($ZnBr_2+KCl+EMPBr$) could be suitable as an electrolyte in the Zn-Br redox flow battery with non-appeared bubble, non-Br formation and high anodic-cathodic maximum current density.

• Journal of Powder Materials
• /
• v.18 no.6
• /
• pp.575-582
• /
• 2011

MAO(Micro-Arc Oxidation) method was used to make $Al_2O_3$ surface on 6063 Al specimen. This study was focused on an influence of voltage, density of electrolyte and a period of treatment on the change of surface microstructure by using SEM(Scanning Electron Microscope), EDS(Energy Dispersive X-ray Spectroscopy). The microstructure shows higher roughness and thicker oxidized layer with increase of voltage and maintaining period of treatment. The density of electrolyte affected a formation of more dense surface and increase of a oxidized layer.

• Journal of the Korean Electrochemical Society
• /
• v.6 no.3
• /
• pp.174-177
• /
• 2003

Electric double-layer capacitors based on charge storage at the interface between a high surface area activated carbon electrode and an electrolyte solution are characterized by their long cycle-life and high power density in comparison with batteries. However, energy density of electric double-layer capacitors obtained at present is about 6 Wh/kg at a power density of 500W/kg which is smaller as compared with that of batteries and limits the wide spread use of the capacitors. Therefore, a new capacitor that shows larger energy density than that of electric double-layer capacitors is proposed. The new capacitor is the hybrid capacitor consisting of activated carbon cathode, carbonaceous anode and an organic electrolyte. Maximum voltage applicable to the cell is over 4.2V that is larger than that of the electric double-layer capacitor. As a result, discharged energy density on the basis of stacked volume of electrode, current collector and separator is more than 18Wh/l at a power density of 500W/l.

• Transactions of the Korean hydrogen and new energy society
• /
• v.26 no.4
• /
• pp.324-330
• /
• 2015

The electrolyte flow rates of vanadium redox flow battery play very important role in terms of ion transfer to electrolyte, kinetics and pump efficiency in system. In this paper a vanadium redox flow battery single cell was tested to suggest the optimization criteria of electrolyte flow rates on the efficiencies. The compared electrolyte circulation flow rates in this experimental work were 15, 30 and 45 mL/min. The charge/discharge characteristics of the flow rate of 30 mL/min was the best out of all flow rates in terms of charging and discharging time. The current efficiencies, voltage efficiencies and energy efficiencies at the flow rate of 30 mL/min were the best. The IR losses obtained at thd current density of $40mA/cm^2$, at the flow rates of 15, 30 and 45 mL/min were 0.085 V, 0.042 V and 0.115 V, respectively. The charge efficiencies at the current density of $40mA/cm^2$ were 96.42%, 96.45% and 96.29% for the electrolyte flow rates of 15, 30 and 45 mL/min, respectively. The voltge efficiencies at the current density of $40mA/cm^2$ were 77.34%, 80.62% and 76.10% for the electrolyte flow rates of 15, 30 and 45 mL/min, respectively. Finally, the energy efficiencies at the current density of $40mA/cm^2$ were 74.57%, 77.76% and 73.27% for the electrolyte flow rates of 15, 30 and 45 mL/min, respectively. The optimum flow rates of electrolytes were 20 mL/min in most of operating variables of vanadium redox flow battery.

• Journal of the Korean institute of surface engineering
• /
• v.30 no.1
• /
• pp.44-56
• /
• 1997

Influence of electrochemical etching conditions on capacitance gain of aluminium electrolytic on capacitor foil has been investigated by etching cubic textured high purity aluminum foil in dilute hydrochloric acid. Uniformly distributed etch pit tunnels on aluminum surface have been obtained by pretreatment aluminium foil in 10% NaOH solution for 5 minutes followed by electrochemical etching. Electrostatic capacitance of etched aluminium foil anodized to high voltage increased with the increase of current density, total charge, temperature and concentration of electrolyte up to maximum CV-value and then deceased. Election optical observation of the etched foil revealed that the density of etch of etch pits increased with the increase of current density and concentration of electrolyte. this increase of etch pit density enlarged of the increase of capacitance. However, abnormal high current density and high electrolyte concentration induced the local dissolution of the foil surface which resulted the decrease of foil capacitance.

• Journal of the Korean institute of surface engineering
• /
• v.18 no.4
• /
• pp.164-183
• /
• 1985

The microstructure of the zinc electrodeposits was investigated by changing the flow rate of electrolyte in zinc sulfate Bath. The cathode current efficiency increased with increasing flow rate of electrolyte. The preferred orientation of zinc electrodeposit changed from (11.2) texture to (10.3) or (10.1)+(10.2) texture with increasing current density in the range of flow rate, 0.2-1.2m/sec. The morphology of the deposits changed from the sponge deposit to the blocks of hexagonal crystallites packed together through the structures of find polycrystallite with increasing current density. The microstructure of the cross-section of the above deposits are granular structure and columnar structure respectively. The surface roughness of zinc electrodeposits decreased with increasing current density and flow rate of electrolyte.