• Transactions of the Korean hydrogen and new energy society
• /
• v.27 no.2
• /
• pp.135-143
• /
• 2016

Biogas is a renewable fuel from anaerobic digestion of organic matters such as sewage sludge, manure and food waste. Raw biogas consists mainly of methane, carbon dioxide, hydrogen sulfide, and water. Biogas may also contain other impurities such as siloxanes, halogenated hydrocarbons, aromatic hydrocarbons. Efficient power technologies such as fuel cell demand ultra-low concentration of containments in the biogas feed, imposing stringent requirements on fuel purification technology. Biogas is upgraded from pressure swing adsorption after biogas purification process which consists of water, $H_2S$ and siloxane removal. A polymer electrolyte membrane fuel cell power plant is designed to operate on reformate produced from upgraded biogas by steam reformer.

• Transactions of the Korean hydrogen and new energy society
• /
• v.27 no.5
• /
• pp.503-509
• /
• 2016

Fuel cell is a device for producing electricity by using the hydrogen produced by the fuel processor. At this time, CO is also created by the fuel processor. The resulting CO enters the stack where is produce electricity and leads to the adsorption of anode catalyst, finally the CO poisoning occurs. Stack which occurred CO poisoning has a reduction in performance and shelf life are gradually fall because they do not respond to hydrogen. In this paper, experiments that using a PROX reactor to prevent CO poisoning were carried out for removing the CO concentration to less than 10ppm range available in the fuel cell. Furthermore experiments by the PROX reaction was designed and manufactured with a water-cooling heat exchange reactor to maintain a suitable temperature control due to the strong exothermic reaction.

• Journal of Sensor Science and Technology
• /
• v.17 no.5
• /
• pp.329-337
• /
• 2008

Simple, small and portable oxygen sensors were fabricated by tape casting technique. Yttria stabilized zirconia containing cordierite ceramics (YSZC) were used as a porous diffused layer of oxygen in pumping cell. Yttria stabilized zirconia (YSZ) solid electrolyte, YSZC porous diffusion layer and heater-patterned ceramic sheets were prepared by co- firing method. Limit current characteristics and the linear relationship of current to oxygen concentration were observed. Viscosity variation of the slurries both YSZ and YSZC showed a similar behavior, but micro pores in the fired sheet were increased with increasing of the cordierite amount. Molecular diffusion was dominated due to the formation of large pores in porous diffusion layer. The plateau range of limit current in porous-type oxygen sensor was narrow than the one of aperture-type oxygen sensor. However limit current curve was appeared in porous-type oxygen sensor even at the lower applied voltage. The plateau range of limit-current was widen as increasing the thickness of porous diffusion layer of the YSZ containing cordierite. Measuring temperature of $600{\sim}650^{\circ}C$ was recommended for limit-current oxygen sensor. Porous diffusion layer-type oxygen sensor showed faster response than the aperture-type one and was stable up to 30 days running without any crack at interface between the layers.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.407-408
• /
• 2005

High surface area electrodes for aluminum electrolytic capacitors are produced by AC electrochemical processes. Optimization of crystallographic etch pit growth on aluminium during AC etching of cathode film for aluminium as electrolytic capacitor has been established. In this work, we present the observations of pit distributions by galvanostatic measurements. The effects of electrolyte concentration, current density, frequency, various pre-treatments and etching time have been studied. The specimen was pretreated in 0.5M NaOH and 1M HCl at $40\sim60^{\circ}C$, and transferred into a cell containing 1M HCl, then various mol $H_2SO_4$ etchant was added. Pit size distributions were determined with scanning electron microscopy (SEM).

• Bulletin of the Korean Chemical Society
• /
• v.21 no.6
• /
• pp.571-576
• /
• 2000

Electrocatalytic effects for the reduction of thionyl chloride in $LiAICI_4/SOCl_2$ electrolyte solution containing Schiff base M(II) (M; Co and Fe) complexes are evaluated by determining kinetic parameters with cyclic voltammetry and chronoamperometry at a glassy carbon electrode. The charge transfer process during the reduction of thionyl chloride is affected by the concentration of the catalyst. The catalytic effects are demonstrated from both a shift of the reduction potential for the thionyl chloride toward a more positive direction and an increase in peak currents. Catalytic effects are larger in thionyl chloride solutions containing the binuclear [M(II) $_2$ (TSBP)] complex rather than mononuclear [M(II)(BSDT)] complexes. Significant improvements in the cell performance have been noted in terms of both thermodynamics and activation energy for the thionyl chloride reduction. The activation energy calculated from the Arrhenius plots is 4.5-5.9 kcal/mole at bare glassy carbon electrodes. The activation energy calculated for the catalyst containing solution is 3.3-4.9 kcalmole, depending on whether the temperature is lowered or rasied.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.18 no.4
• /
• pp.549-562
• /
• 2020

Deionized water, methanol, and ethanol were investigated for their effectiveness at dissolving LiCl-KCl-UCl3 at 25, 35, and 50℃ using inductively coupled plasma mass spectrometry (ICP-MS) to study the concentration evolution of uranium and mass ratio evolutions of lithium and potassium in these solvents. A visualization experiment of the dissolution of the ternary salt in solvents was performed at 25℃ for 2 min to gain further understanding of the reactions. Aforementioned solvents were evaluated for their performance on removing the adhered ternary salt from uranium dendrites that were electrochemically separated in a molten LiCl-KCl-UCl3 electrolyte (500℃) using scanning electron microscopy with energy dispersive spectroscopy (SEM-EDS). Findings indicate that deionized water is best suited for dissolving the ternary salt and removing adhered salt from electrodeposits. The maximum uranium concentrations detected in deionized water, methanol, and ethanol for the different temperature conditions were 8.33, 5.67, 2.79 μg·L-1 for 25℃, 10.62, 5.73, 2.50 μg·L-1 for 35℃, and 11.55, 6.75, and 4.73 μg·L-1 for 50℃. ICP-MS analysis indicates that ethanol did not take up any KCl during dissolutions investigated. SEM-EDS analysis of ethanol washed uranium dendrites confirmed that KCl was still adhered to the surface. Saturation criteria is also proposed and utilized to approximate the state of saturation of the solvents used in the dissolution trials.

• Korean Journal of Metals and Materials
• /
• v.49 no.5
• /
• pp.419-424
• /
• 2011

Carbon nanotubes (CNTs) were directly synthesized on a copper (Cu) plate as a current collector by the catalytic thermal vapor deposition method for an electric double-layer capacitor (EDLC) electrode. The diameters of vertically aligned CNTs grown on the Cu plate were 20~30 nm. From cyclic voltammetry (CV) results, the CNTs/Cu electrode showed high specific capacitance with typical profiles of EDLCs. Rectangularshaped CV curves suggested that the CNTs/Cu electrode could be an excellent candidate for an EDLC electrode. The specific capacitances were in a range of 25~75 F/g with a scan rate of 10~100 mV/s and KOH electrolyte concentration 1~6 M, and were maintained up to 1000 charge/discharge cycles due to strong adhesion between the Cu substrate and the CNTs.

• Corrosion Science and Technology
• /
• v.20 no.6
• /
• pp.435-450
• /
• 2021

The interest in eco-friendly energy is increasing, and polymer electrolyte membrane fuel cell (PEMFC) is attracting attention as alternative power sources. Research on metallic bipolar plates, a fuel cell component, is being actively conducted. However, since the operating conditions of PEMFC, in which sulfuric acid (H₂SO₄) and hydrofluoric acid (HF) are mixed, are strong acidity, the durability of the metallic bipolar plate is very important. In this research, the electrochemical characteristics and corrosion damage behavior of 316L stainless steel, a material for metallic bipolar plates, were analyzed through potentiostatic corrosion tests with test times and chloride concentrations. As the test times and chloride concentrations increased, the current density and corrosion damage increased. As a result of observation with scanning electron microscope(SEM) and 3D microscope, both the depth and width of pitting corrosion increased with increases in test times and chloride concentrations. In particular, the pitting corrosion damage depth at test conditions of 6 hours and 1000 ppm chloride increased the most. The growth of the pitting corrosion damage was not directly proportional to time and increased significantly after a certain period.

• Corrosion Science and Technology
• /
• v.20 no.6
• /
• pp.347-360
• /
• 2021

Currently, the demand for eco-friendly energy sources is high, which has prompted research on polymer electrolyte membrane fuel cells. Both aluminum alloys and nickel alloys, which are commonly considered as materials of bipolar plates in fuel cells, oxide layers formed on the metal surface have excellent corrosion resistance. In this research, the electrochemical characteristics of 6061-T6 aluminum alloy and Inconel 600 were investigated with chloride concentrations in an acid environment that simulated the cathode condition of the PEMFC. After potentiodynamic polarization experiments, Tafel analysis and surface analysis were performed. Inconel 600 presented remarkably good corrosion resistance under all test conditions. The corrosion current density of 6061-T6 aluminum alloy was significantly higher than that of Inconel 600 under all test conditions. Also, 6061-T6 aluminum alloy and Inconel 600 presented uniform corrosion and intergranular corrosion, respectively. The Ni, Cr, and Fe, which are the main chemical compositions of Inconel 600, are higher than Al in the electromotive force series. And a double oxide film of NiO-Cr₂O₃, which is more stable than Al₂O₃, is formed. Thus, the corrosion resistance of Inconel 600 is better.

• Korean Journal of Veterinary Research
• /
• v.61 no.4
• /
• pp.40.1-40.6
• /
• 2021

Acid-base disorder is a common problem in veterinary emergency and critical care. Traditional methods, as well as the Stewart method based on strong ion difference concepts and the Fencl-Stewart method, can be used to analyze the underlying causes. On the other hand, there are insufficient comparative study data on these methods in cats. From 2018 to 2020, 327 acid-base analysis data were collected from 69 sick and 18 healthy cats. The three most well-known methods (traditional method, Stewart method, and Fencl-Stewart method) were used to analyze the acid-base status. The frequency of acid-base imbalances and the degree of variation according to the disease were also evaluated. In the traditional acid-base analysis, 5/69 (7.2%) cats showed a normal acid-base status, and 23.2% and 40.6% of the simple and mixed disorders, respectively. The Fencl-Stewart method showed changes in both the acidotic and alkalotic processes in 64/69 (92.8%), whereas all cats showed an abnormal status in the Fencl-Stewart method (semiquantitative approach). The frequencies of the different acid-base imbalances were identified according to the analysis method. These findings can assist in analyzing the underlying causes of acid-base imbalance and developing the appropriate treatment.