• Korean Journal of Veterinary Research
• /
• v.30 no.1
• /
• pp.15-27
• /
• 1990

Effects of oral administration of electrolyte solutions were studied in experimentally dehydrated adult sheep. By the latin square method five ruminal fistulated sheep were examined and dehydrated by deprivation of feed and water for 72 hours. Tap water, physiological saline, 0.45% NaCl+120 mM/L glucose and 0.9% NaCl+1% propylene glycol solution were orally administrated after dehydration, respectively. Rehydration effect and modification of the rumen function were compared. 1. After 72 hours of deprivation of feed and water, sheep were hypertonic dehydrated and blood acid-base parameters were not significantly changed. And there was marked increase in ruminal pH and decrease in ruminal total volatile fatty acid(VFA) concentration. 2. After the fluids administration the changes in blood acid-base parameters were not significant in all groups. 3. Although glucose fermentation in the rumen was observed, 0.45% NaCl+120 mM/L glucose was more effective in rehydration than physiological saline and tap water. But it was difficult to know the rehydration effect of 0.9% NaCl+1% propylene glycol solution exactly because of excessive increase in plasma osmolality. 4. After refeeding, total concentration and proportions of ruminal volatile fatty acid(VFA) were not significantly different among groups and recovered to normal concentration but not in proportions after 2 days in all groups. 5. In vitro cultured ruminal protozoa were susceptible to the decrease of the pH and osmolality.

• Corrosion Science and Technology
• /
• v.5 no.4
• /
• pp.129-136
• /
• 2006

High temperature corrosion behavior of AISI-type 316L stainless steel for the MCFC(molten carbonate fuel cell) bipolar application was studied by immersion test and penetration attack method in anode environment ($650^{\circ}C$, $Li_2CO_3/K_2CO_3=62/38$ mol%, $H_2/CO_2=80/20$ vol%) without or with different $CaCO_3$ content. Not only immersion test method but also morphological observation of samples in the carbonate melts are adopted as experimental methods. With aid of the morphological observation of cross section of samples immersed in a carbonate melt was possible to obtain penetration attack. The concentration effect of $CaCO_3$ inhibitor was investigated in order to verify the optimum concentration for practical application in MCFC stack operation. The corrosion rate in the presence of $CaCO_3$ was proven to be decreased as a function of $CaCO_3$ concentration. The corrosion rate in the presence of $CaCO_3$ was measured with a value of 6.9 mpy which is 2.4 times lower than that of inhibitor-free electrolyte. The cross section microscopy revealed that the internal penetration by oxidation in molten carbonate is very severe. In this case, the attack was occurred not only dissolution loss in the electrolyte by corrosion reaction but also weight gain through oxide layer by internal penetration.

• Journal of Pharmaceutical Investigation
• /
• v.34 no.6
• /
• pp.491-497
• /
• 2004

We investigated some important factors which affect the transdermal flux of ketoprofen, a nonsteroidal anti-inflammatory agent, as a first step to provide some basic knowledge for the development of a iontophoretic transdermal patch system. Factors such as current density, polarity, buffer (HEPES) and electrolyte concentration and pH were studied using hairless mouse skin. The effect of poly(L-lysin), which is known to affect the electro-osmotic flow through skin, on flux was also studied. Passive flux was about $20\;{\mu}g/cm^2hr$ at pH 4.0, but was negligible at pH 7.4 where all ketoprofen molecules dissolved are ionized (ketoprofen pKa=5.94). At pH 4.0, application of anodal current increased the flux further above the passive level, however anodal flux at pH 7.4 was much smaller than passive flux at pH 4.0. The application of cathodal current at pH 4.0 increased the average flux to $30-40\;{\mu}g/cm^2hr$, depending on the current density applied. At pH 7.4, cathodal flux was only about $5\;{\mu}g/cm^2hr$. Decrease in buffer and electrolyte concentration increased this cathodal flux about 10 fold. However decrease in HEPES buffer concentration 100 fold did not affect the flux. Anodal flux of acetaminophen was much larger than cathodal flux, indicating that electroosmotic flow can be playing an important role in the flux. Poly(L-lysin) increased the cathodal flux at pH 7.4. These results provide some important insights into the mechanism of transdermal flux of ketoprofen and the role of electroosmotic flow.

• Transactions of the Korean hydrogen and new energy society
• /
• v.32 no.4
• /
• pp.228-235
• /
• 2021

Polymer electrolyte membrane fuel cells (PEMFC) are currently being used in various transport applications such as drones, unmanned aerial vehicles, and automobiles. The power required is different according to the type of use, purpose, and the conditions adjusted using a cell stack. The fuel cell stack is compressed to reduce the size and prevent fuel leakage. The unit cells that make up the cell stack are subjected to compression by clamping force, which makes geometrical changes in the porous media and it impacts on cell performance. In this study, finite elements method (FEM) and computational fluid dynamics (CFD) analysis for the deformed unit cell considering the effects of clamping force is performed. First, structural analysis using the FEM technique over the deformed gas diffusion layer (GDL) considering compression is carried out, and the resulting porosity changed in the GDL is calculated. The PEMFC model is then verified by a three-dimensional, two-phase fuel cell simulation applying the physical properties and geometry obtained before and after compression. The detailed simulation results showed different concentration distributions of fuel between the original and deformed geometry, resulting in the difference in the distribution of current density is represented at compressed GDL region with low oxygen concentration.

• Applied Chemistry for Engineering
• /
• v.9 no.7
• /
• pp.1030-1035
• /
• 1998

The porous alumina membrane was prepared from aluminum metal(99.8%) by anodic oxidation using DC power supply of constant current mode in an aqueous solution of sulfuric acid. To prevent the chemical dissolution of alumina membrane, $Al_2(SO_4)_3$, $AlPO_4$ and $Al(NO_3)_3$ which could be considered to supply $Al^{3+}$ ions were added to electrolyte solution at a reaction temperature of $20^{\circ}C$ and cumulative charge of $150C/cm^2$. Effects of these additives on the formation of porous alumina membrane were evaluated under various electrolyte concentration(5~20 wt%) and current densities($10{\sim}50mA/cm^2$). The membrane surfaces which were prepared in electrolyte solution with all the additives except $Al_2(SO_4)_3$ were damaged. However, when $Al_2(SO_4)_3$ was added to the $H_2SO_4$ solution, an uniform surface of porous alumina was obtained. Also, it was shown that the pore size of membrane was nearly independent on the quantity of $Al_2(SO_4)_3$ added at same electrolyte concentration and current density.

• Resources Recycling
• /
• v.27 no.6
• /
• pp.44-52
• /
• 2018

In this study, copper was recovered from copper containing sludge by selectively controlling electro-refining process conditions in copper sulfate electrolyte solution. Electro-refining process was performed by LSV (Linear Sweep Voltammetry) result according to copper sulfate electrolyte solution concentration, applied current density, additive type and concentration. SEM (Scanning Electron Microscope) and PSA (Particle Size Analyzer) were used to analyze the shape and size of copper powder. In the 0.1 ~ 0.4 M copper sulfate electrolyte solution without organic additives, the copper powder size decreased as the applied current density became closer to the limiting current density and the copper powder size tended to decrease in 0.2 ~ 0.3 M copper sulfate electrolyte solution. In addition, when the shape and size of the copper powder were analyzed by adding various types and concentrations of organic additives to the previous experimental, fine spherical copper powder having the smallest size (nm) was obtained under the condition of cellulose type additive 2,000 ppm.

• Journal of Pharmaceutical Investigation
• /
• v.25 no.2
• /
• pp.95-100
• /
• 1995

Serum electrolyte concentration and body weight were determined before and after exercise for 2h in Korean cyclists. The serum concentration of electrolytes (Na, Ca, Zn, K, P and Cl) was increased but that of Mg was decreased as a result of exercise. The increase of serum K and P concentration was statistically significant after exercise. As the exercise time increased, the loss of body weight also increased due to dehydration and sweat. The loss of body weight ranged 1.0 to 2.3 Kg as a function of exercise time but cyclists showed the exhaustion and muscle fatigue 2h after exercise. As the ambient temperature increased, the loss of body weight was slightly increased. However, frequent drinking water was required because of dehydration and thirst. Although frequent drinking water may reduce weight loss and thirst during exercise, sports drinking beverages simultaneously containing electrolytes and nutrients are more useful to replenish loss of water and electrolytes in an exhausted condition, resulting in the improvement of physical performance.

• Transactions of the Korean hydrogen and new energy society
• /
• v.19 no.3
• /
• pp.209-216
• /
• 2008

In the present study, a mathematical model has been formulated for the performance of polymer electrolyte fuel cells. Modify the concentration polarization equation using concentration coefficient that represents the characteristics of bipolar plate reactant distribution. The model predictions have been compared with experimental results and good agreement has been demonstrated for the cell polarization curves. The effects of operating parameters on the performance of fuel cells have been studied. Increases of operation pressure reduce the effect of temperature on the performance.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.505-506
• /
• 2008

The direct methanol fuel cell (DMFC) is a promising power source for portable applications due to many advantages such as simple construction, compact design, high energy density, and relatively high energy-conversion efficiency. In this work, an electrochemical methanol sensor for monitoring the methanol concentration in direct methanol fuel cells was fabricated using a thin composite nafion membrane as the electrolyte. We have analyzed the I-V characteristic of the fabricated methanol sensor as a function of methanol concentration, catalyst electrode and platinum(Pt) dot.

• Journal of the Korean Chemical Society
• /
• v.30 no.2
• /
• pp.224-230
• /
• 1986

Dodecyltrimethylammonium bromide (DTAB) was examined as a counter-ion in the separation of aromatic sulfonic acids on alkylmodified silica (ODS) column by reversed-phase ion-pair chromatography. The capacity factor of acids was investigated and separation was attempted. The capacity factor of samples was influenced by the several factors such as a concentration of counter-ion, concentration of methanol, kinds and concentration of electrolyte in mobile phase as well as kinds and position of functional group in samples. Some mixtures of samples were able to be separated under optimum condition.