• Journal of the Korean Magnetics Society
• /
• v.4 no.2
• /
• pp.106-113
• /
• 1994

This paper deals with the magnetic forces of the combined levitation and guidance EDS(Electrodynamic Suspension) maglev system when the car bogie is tilted by the roll, pitch and yaw. The end effect on the magnetic forces are considered by calculating the air-gap flux without the assumptions for its pattern. Induced voltages and currents of the ground coils are given as results. The restoring torque due to roll, pitch and yaw of the bogie body are also examined. It has been shown that the end effect of the concentrically loaded vehicle are not negligible and the combined EDS is stable maglev system against disturbing forces.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.11
• /
• pp.794-801
• /
• 2017

When a radial wheel is placed so as to partially overlap a conductive plate and rotated, a lift force is generated on the wheel, a thrust force along the edge, and a lateral force which tends to reduce the overlap region. When several of these wheels are combined, it is possible to realize a system in which the stability of the remaining axes is ensured, except in the traveling direction. To validate the overall characteristics of the multi-wheel system, we propose a transfer system levitated magnetically using radial electrodynamic wheels. The proposed system is floated and propelled by four wheels and arranged in a structure that allows the thrusts generated by the front and rear wheels to offset each other. The dynamic stability of the wheel and the effect of the pole number on the three-axial forces are analyzed by the finite element method. At this time, the thrust and levitation force are strongly coupled, and the only factor affecting them is the wheel rotation speed. Therefore, in order to control these two forces independently, we make use of the fact that the ratio of the thrust to the levitation force is proportional to the velocity and is independent of the size of the gap. The in-plane and out-of-plane motion control of the system is achieved by this control method and compared with the simulation results. The experimental results show that the coupled degrees of freedom can be effectively controlled by the wheel speed alone.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.10
• /
• pp.1767-1776
• /
• 2008

This paper presents the status of advanced technologies and domestic researches for development of Korean next generation maglev. Generally, two specific configurations such as the EMS (Electromagnetic Suspension) with LSM (Linear Synchronous Motor) and EDS (Electrodynamic Suspension) with LSM can be employed as a propulsion and levitation device of high-speed maglev. Worldwide high-speed maglev developments refer to projects such as the German Transrapid with EMS, the Japanese MLX with EDS, and the U.S. Inductrack with PM (Permanent Magnet) EDS maglev system. In this paper, the propulsion and levitation systems of these world wide high-speed maglev have been reviewed and analysed.

• Journal of Institute of Convergence Technology
• /
• v.3 no.1
• /
• pp.1-8
• /
• 2013

High-precision surface actuator, in which in-plane motion is realized by not two-dimensional actuator superposing linear actuators but integrated planar actuator, has been developed to cope with the severe target performance like precise motion with large envelope. It is very difficult to accomplish the performance with the traditional actuating principle. So, various methods have been tried to break through the problem. This paper discusses some meaningful trials performed in the Nano Measurement and Precision Motion Control Lab. of Korea National University of Transportation.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.9
• /
• pp.643-651
• /
• 2020

A capsule train runs inside a sub-vacuum tube and can reach very high speed due to the low air resistance. A capsule train uses a superconducting electrodynamic suspension (SC-EDS) method for levitation, which allows for a large levitation gap and does not require gap control. However, SC-EDS has inherent characteristics such as the large gap variation and a small damping effect in the levitation force, which can degrade the running stability and ride comfort. To overcome this, a stability improvement device should be designed and applied based on dynamic analysis. In this study, a 1/10 small-scale testbed was developed to replicate the dynamic characteristics of a capsule train and investigate the performance of stability improvement devices. The testbed is composed of a 6-degree-of-freedom Stewart platform for the realization of bogie motion, a secondary suspension with a running stabilization device, and a carbody. Based on the dynamic similarity law proposed by Jaschinski, the small-scale testbed was manufactured, and a bogie motion algorithm was applied with the consideration of guideway irregularity and levitation stiffness. The experimental results from the testbed were compared with simulation results to investigate the performance of the testbed.

• Journal of Institute of Control, Robotics and Systems
• /
• v.19 no.7
• /
• pp.626-632
• /
• 2013

When a conductive rod is put within rotating axial magnet wheels arranged parallel, three-axial magnetic forces generate on the rod. In some region, the forces has a property of negative stiffness, thus they can be applied to noncontact conveyance of the rod without a control load. Apart from the passive driving, the magnet wheel should be controlled for the rod to be stayed at the still state or be moved in a specified velocity. But, because a control input is just the rotating speed of the magnet wheel, the number of input is less than that of variables to be controlled. It means that levitation force and thrust force increase at the same time for increasing wheel speed, resulting from a strong couple between two forces. Thus, in this paper, a novel method, in which the longitudinal motion of the rod is controlled indirectly by the normal motion of the rod with respect to the wheel center, is introduced to manipulate the rod without mechanical contact on space.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.311-316
• /
• 2010

The ignition and the burning characteristics of aluminum and magnesium particles ($30-110{\mu}m$ in diameter) isolated due to electrodynamic levitation were experimentally investigated. The burning time, the ignition delay time, the flame temperature, and the flame diameter were measured. The thermal radiation intensity was measured using the photomultiplier tube and the combustion history was monitored by high-speed cinematography. Two-wavelength pyrometry measured the temperature of the burning particles. The burning times of aluminum particles were measured approximately 5 to 8 times longer than those of magnesium particles. Exponents of $D^n$-law, for the burning rate of magnesium and aluminum particles of diameters less than $110{\mu}m$, are found to be 0.6 and 1.5, respectively. The instant of aluminum ignition is clearly distinguished with the ignition delay time little less than 10 ms, however the burning history of magnesium particle exhibits no distinct instant of the ignition. The ignition delay time of magnesium particle (less than $110{\mu}m$) were approximately shown in the range from 50 to 200 ns. The flame temperatures of single metal particles are lower than the boiling point of the oxide. The nondimensional flame diameters for magnesium are decreased with increasing of the diameter. The nondimensional flame diameters for aluminum are not changed significantly.

• Journal of Magnetics
• /
• v.18 no.3
• /
• pp.370-374
• /
• 2013

This paper introduces an innovative hybrid array consisting of both permanent and electro magnets. It will enable us to develop an active control mechanism for underdamped electro-dynamic suspension (EDS) Maglev systems. The proposed scheme is based on the Halbach array configuration which takes the major technical advantage from the original Halbach characteristics: a strongly concentrated magnetic field on one side of the array and a cancelled field on the opposite side. In addition, the unique feature of the proposed concept only differs from the Halbach array with permanent magnets. The total magnetic field of the array can be actively controlled through the current of the electro-magnet's coils. As a result, the magnetic force produced by the proposed hybrid array can also be controlled actively. This study focuses on the magnetic characteristics and capability of the proposed array as compared to the basic Halbach concept. The results show that the proposed array is capable of producing not only an equivalent suspension force of the basic Halbach permanent magnet array but also a controlled mode. Consequently, the effectiveness of the proposed array confirms that this study can be used as a technical framework to develop an active control mechanism for an EDS Maglev system.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.10
• /
• pp.547-557
• /
• 2020

In this study, damping control devices were applied to the suspension system of a capsule train, and the effects were investigated to improve the ride comfort. The superconductor electrodynamic suspension (SC-EDS) method is used for the capsule train levitation. This method has advantages such as no gap control and a large gap. However, the SC-EDS method has disadvantages such as large gap variation and small damping characteristics against outer vibration, which causes degradation of the ride comfort. In this study, the damping control devices in the primary and secondary suspension were considered to improve the ride comfort in the capsule train. Damping control devices in the primary and secondary suspension can reduce the vibration transmission from outer disturbances to the bogie and from the bogie to the car body, respectively. Simulations for dynamic characteristics analyses were conducted based on the capsule train dynamic model to investigate the effects of the damping control devices on the ride comfort. As a result, it was confirmed that the ride comfort requirements according to the ISO standard can be satisfied by applying the damping control in the capsule train suspension.