• Journal of the Korean Society of Safety
• /
• v.27 no.3
• /
• pp.63-70
• /
• 2012

In the hazardous areas where explosive gases, vapor or mists exist, electrical apparatus and installations must be the explosion-proof construction to prevent or limit the danger of the ignition of potentially explosive atmosphere. In Korea, nine types of protection have been specified in the government regulations at present: flameproof enclosure, pressurization, oil immersion, increased safety, intrinsic safety, non-incendive, powder filling, encapsulation, and special types. Among these types, the intrinsic safety has the construction which limit or by-pass igniting the electric energy using electronic devices. This type has lots of merits but at the same time requires a high-degree of technology. In this paper, we investigated several dominating factors which affect the minimum ignition energy; this energy plays a very important role in design and evaluation of the intrinsic safety type electrical apparatus. Electrode material, which is one of the most important factors, was intensively studied for the five sorts of material(Al, Cd, Mg, Sn, and Zn) with performing experiment in a low-voltage inductive circuit using IEC-type(International Electro-technical Commission) spark apparatus. The experimental results show that the minimum ignition energy of electrode material is varied: highest in Cd and lowest in Sn. We also confirmed the effect of electrode make-and-break speed.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.1850-1852
• /
• 2000

In this paper, new Partial Discharge (PD) detection technique using Pockels cell was proposed and considerable apparent chaotic characteristics were discussed. For this purpose, PD was generated from needle-plane electrode in air and detected by optical measuring system using Pockels cell, based on Mach-Zehnder interferometer, consisting of He-Ne laser, single mode optical fiber, 50/50 beam splitter and photo detector. A qualitative analysis was carried out by drawing Return map for the normalized time series of the detected PD signals. The results are as follows:(a) Fixed points, between 0.7 and 1.0, are appeared clearly in the right upper area of the return map as the increase in the number of obtained data.(b) Considerable periodicity have been remarked even though exact period and length can not be determined.(c) The self-similarity can be also observed inasmuch as the late paths do not follow the previous ones. Accordingly, exact quantitative analysis such as embedding dimension, fractal dimension, and Lyapunov exponents should be carried out for deducing the quantitative properties regarding PD phenomena.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.3
• /
• pp.370-375
• /
• 2010

Tungsten carbide microshaft is used as micro punch, electrode of micro electro discharge machining, and micro tool because of its high hardness and rigidity. In this research, tungsten carbide microshaft was fabricated using electrochemical machining. $H_2SO_4$ solution was used as the electrolyte because it can dissolve tungsten carbide and cobalt simultaneously. Experimentally studied were the effects of electrolyte concentration, machining time, and machining voltage on material removal rate and the shape of the microshaft. To eliminate the effects of bubbles and metal corrosion layer on microshaft shape, the machining was performed below the electrolysis voltage. Three step electrochemical process was suggested to fabricate the straight tungsten carbide microshaft. As a result, a straight tungsten carbide microshaft of $30{\mu}m$ in diameter and $500{\mu}m$ in length was obtained through the proposed three step electrochemical process.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.2
• /
• pp.635-642
• /
• 2014

The space charge behaviors of oil-paper insulation affect the stability and security of oil-filled converter transformers of traditional and new energies. This paper presents the results of the electrical aging of oil-impregnated paper under AC-DC combined voltages by the pulsed electro-acoustic technique. Data mining and feature extractions were performed on the influence of electrical aging on charge dynamics based on the experiment results in the first stage. Characteristic parameters such as total charge injection and apparent charge mobility were calculated. The influences of electrical aging on the trap energy distribution of an oil-paper insulation system were analyzed and discussed. Longer electrical aging time would increase the depth and energy density of charge trap, which decelerates the apparent charge mobility and increases the probability of hot electron formation. This mechanism would accelerate damage to the cellulose and the formation of discharge channels, enhance the acceleration of the electric field distortion, and shorten insulation lifetime under AC-DC combined voltages.

• Korean Journal of Optics and Photonics
• /
• v.12 no.2
• /
• pp.115-120
• /
• 2001

In the present study, we described in detail a precise correction method of the copper emission spectra obtained from a highpressure and high-temperature pulsed plasma-jet. The pulsed plasma-jet is initiated from an electro-thermal capillary discharge through a small orifice, and expanded rapidly into an atmosphere. In order to characterize the plasma, fundamental measurements such as the plasma excitation temperature or electron number density are essential. However those spectral lines which are directly related to the excitation temperature or electron number density may be distorted by the spectral response of the optical instruments used. Therefore, in this paper, we discuss some efforts to derive precise correction methods of the copper emission spectra obtained from the pulsed plasma-jet. a-jet.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.12 no.2
• /
• pp.150-154
• /
• 2019

In the design of semiconductor integrated circuits, ESD is one of the important issues related to product quality improvement and reliability. In particular, as the process progresses and the thickness of the gate oxide film decreases, ESD is recognized as an important problem of integrated circuit design. Many ESD protection circuits have been studied to solve such ESD problems. In addition, the proposed device can modify the existing SCR structure without adding external circuit to effectively protect the gate oxide of the internal circuit by low trigger voltage, and prevent the undesired latch-up phenomenon in the steady state with high holding voltage. In this paper, SCR-based novel ESD(Electro-Static Discharge) device with the high holding voltage has been proposed. The proposed device has the lower triggering voltage without an external trigger circuitry and the high holding voltage to prevent latch-up phenomenon during the normal condition. Using TCAD simulation results, not only the design factors that influence the holding voltage, but also comparison of conventional ESD protection device(ggNMOS, SCR), are explained. The proposed device was fabricated using 0.35um BCD process and was measured electrical characteristic and robustness. In the result, the proposed device has triggering voltage of 13.1V and holding voltage of 11.4V and HBM 5kV, MM 250V ESD robustness.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.3 no.4
• /
• pp.269-278
• /
• 2005

In order to produce only a pH-controlled solution without discharging any unwanted solution, this work has developed a continuous electrolytic system with a pH-adjustment reservoir being placed before an ion exchange membrane-equipped electrolyzer, where as a target solution was fed into the pH-adjustment reservoir, some portion of the solution in the pH-adjustment reservoir was circulated through the cathodic or anodic chamber of the electrolyzer depending on the type of the ion exchange membrane used, and some other portion of the solution in the pH-adjustment reservoir was discharged from the electrolytic system through the other counter chamber with its pH being controlled. The internal circulation of the pH-adjustment reservoir solution through the anodic chamber in the case of using a cation exchange membrane and that through the cathodic chamber in the case of using an anion exchange membrane could make the solution discharged from the other counter chamber effectively acidic and basic, respectively. The phenomena of the pH being controlled in the system could be explained by the electro-migration of the ion species in the solution through the ion exchange membrane under a cell potential difference between anode and cathode and its consequently-occurring non-charge equilibriums and electrolytic water- split reactions in the anodic and cathodic chambers.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.15 no.2
• /
• pp.31-38
• /
• 2001

LCD는 비발광형 소자이므로 배면광이 필요하다. 현재의 LCD 배면광용 냉음극 형광램프는 전기-광학적 특성을 좋게 하기 위하여 수은방전을 사용한다. 그러나 수은의 이용은 외부 온도에 따라 특성이 변하는 결점과 환경 문제가 있다. 이 결점을 보완하기 위하여 원통방전형, 미세방전형 그리고 평면방전형 등 세가지 방식의 무수은 램프가 개발되어 왔다. 원통 방전형 무수은 램프는 수은 대신 Xe을 사용한다. Xe 방전이 수축되는 것을 막기 위하여 한쪽 전극은 외벽에 코일형태로 감아서 사용한다. 그리고 코일형태의 전극의 권선 간격을 조절하여 균일한 방전을 얻는다. 이 형태는 무수은 냉음극 형광램프의 두배의 광속을 얻을 수가 있다. 미세방전형 무수은 램프는 두 개의 절연체로 절연되 금속 전극사이의 방전공간에 수많은 미세방전을 일으켜 발광시킨다. 이 방식은 대향 방전구조와 면 방전구조의 두가지가 있다. 이 방식은 전극이 유전체로 둘러쌓여 있으므로 수명이 높다. 새로운 평면방전형 무수은 램프를 개발하였다. 이 램프는 두 개의 유리평판 사이에 방전공간을 만들고 한쪽 유리면의 양쪽 가장자리에 두 개의 전극을 설치하여 면방전을 유도한다. 양쪽 유리면에는 삼원색 형광체를 도포하고 Xe을 봉입하여 Xe의 진공자외선으로 형광체를 발광시킨다. 이 램프는 전극이 유전체로 덮혀있어 수명이 길다. 실험결과 기체압력 6.7[kPa], 구동전압 1,130[V]에서 최대휘도 9,200[$cd/m^2$], 광효율 20.4[lm/W]을 었었고, 기체 압력 2.7[kPa] 구동전압 1,120[V]에서 최대효율 34.1[lm/W], 휘도 1,080[$cd/m^2$]을 얻었다. 현재 무수은 램프는 수은 램프에 비해서 광학적 특성이 좋지 못하다. 무수은 램프에서 좋은 광학적 특성을 얻기 위해 가장 중요한 것은 수축이 없이 방전을 확산시키는 것이다. 이를 위해서 램프구조와 구동법을 최적화하는 것이 필요하다. 또한 기체압력을 높임으로서 Xe의 여기복사를 얻을 수 있었다.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.6 no.4
• /
• pp.130-137
• /
• 1997

The demand for wire-cut EDM is increasing rapidly in the die and tool making industry. In this study machining characteristics such as machining rate, surface roughness, hand drum form and hardness of machined material are investigated experimentally under the conditions varing pulse on time, pulse off time, peak voltage, wire tension after fixing other conditions in SKD 11 and brass and brass workpiece. It was found that various operating conditions had significant influences on machining characteristics. But the hardness of workpiece was uneffected by operating conditions. Also it was obtained experimentally that brass workpeice had better machinability than SKD 11 one.dition according to the current(Ip) in an electric spark machine : 1) Electrode is utilized Cu and Graphite. 2) Work piece is used the material of carbon steel. The condition of experiment is : 1) Current is varied 0.7(A) to 50(A) and the time of electric discharging to work piece in each time is 30(min) to 60(min). 2) After the upper side of work piece was measured in radius(5$\mu$m) of stylus analyzed the surface roughness to ade the table and graph of Rmax by yielding data. 3) Electro wear ratio is : \circled1Cooper was measured ex-machining and post-machining by the electronic balance. \circled2The ex-machining of graphite measured by it, the post-machining was found the data from volume $\times$specific gravity and analyzed to made its table and graph on ground the data. 4) In order to keep the accuracy of voltage affected to the work piece was equipped with the A.V. R and the memory scope was sticked to the electric spark machine. 5) In order to preserve the precision of current, to get rid of the noise occured by internal resistance of electric spark machine and to force injecting for the discharge fluid , it made the fixed table for a work piece to minimize the work error by means of one's failure during the electric discharging.

• Journal of Power Electronics
• /
• v.15 no.6
• /
• pp.1673-1681
• /
• 2015

A low dropout (LDO) regulator with a wide-bandwidth is proposed in this paper. The regulator features a Human Body Model (HBM) 8kV-class high robustness ElectroStatic Discharge (ESD) protection circuit, and two error amplifiers (one with low gain and wide bandwidth, and the other with high gain and narrow bandwidth). The dual error amplifiers are located within the feedback loop of the LDO regulator, and they selectively amplify the signal according to its ripples. The proposed LDO regulator is more efficient in its regulation process because of its selective amplification according to frequency and bandwidth. Furthermore, the proposed regulator has the same gain as a conventional LDO at 62 dB with a 130 kHz-wide bandwidth, which is approximately 3.5 times that of a conventional LDO. The proposed device presents a fast response with improved load and line regulation characteristics. In addition, to prevent an increase in the area of the circuit, a body-driven fabrication technique was used for the error amplifier and the pass transistor. The proposed LDO regulator has an input voltage range of 2.5 V to 4.5 V, and it provides a load current of 100 mA in an output voltage range of 1.2 V to 4.1 V. In addition, to prevent damage in the Integrated Circuit (IC) as a result of static electricity, the reliability of IC was improved by embedding a self-produced 8 kV-class (Chip level) ESD protection circuit of a P-substrate-Triggered Silicon Controlled Rectifier (PTSCR) type with high robustness characteristics.