• 한국재료학회지
• /
• 제11권10호
• /
• pp.863-868
• /
• 2001

The present study was carried out to investigate the effect of MA processing variables on the microstructural properties of composite powders and the coefficient of thermal expansion of pulse electric current sintered AlN-Cu powder compacts. The AlN-Cu powders had a size of less than 15 $\mu\textrm{m}$ with 25 nm size of copper crystallite after MA 32 hours. The finely distributed AlN-Cu powder compacts were completely achieved after PECS. The residual oxygen was considerably removed after hydrogen reduction treatment. The residual carbon was completely removed to 97%. The CTE of AlN-Cu powder compacts showed a good consistency with Kingery-Tuner model when the volume fraction of copper was less than 60%. When it was more than 60%, the CTE had a good agreement with Series model.

• Applied Microscopy
• /
• 제46권1호
• /
• pp.20-26
• /
• 2016

Our work on $Sc_2O_3-W$ matrix dispenser cathodes had been reviewed in this paper. The cathode with uniform distribution of $Sc_2O_3$ had been obtained using liquid-liquid doping method. The cathode had excellent emission property, i.e., the emission current density in pulse condition could reach over $35A/cm^2$. It was found that the cathode surface was covered by a Ba-Sc-O active substance multilayer with a thickness of about 100 nm, which was different from the monolayer and semiconducting layer in thickness. Furthermore, the observation results displayed that nanoparticles appeared at the growth steps and the surface of tungsten grains of the fully activated cathode. The calculation result indicated that the nanoparticles could cause the increase of local electric field strengths. We proposed the emission model that both the Ba-Sc-O multilayer and the nanoparticles distributing mainly on the growth steps of the W grains contributed to the emission. The future work on this cathode has been discussed.

• 세라미스트
• /
• 제22권4호
• /
• pp.332-349
• /
• 2019

Ceramic thin films are key materials for fundamental electronic devices such as transistors and capacitors which are highly important for the state-of-the-art electronic products. Their characteristic dielectric properties enable accurate control of current conduction through channel of transistors and stored charges in capacitor electrodes. The electronic conduction in ceramic thin films is one of the most important part to understand the electrical properties of electronic device based on ceramic thin films. There have been numerous papers dealing with the electronic conduction mechanisms in emerging ceramic thin films for future electronic devices, but these studies have been rarely reviewed. Another interesting electrical characterization technique is one based on electrical pulses and following transient responses, which can be used to examine physical and chemical changes in ceramic thin films. In this review, studies on various conduction mechanisms through ceramic thin films and electrical characterization based on electric pulses are comprehensively reviewed.

• 한국광학회지
• /
• 제16권4호
• /
• pp.366-375
• /
• 2005

Ti 확산 리튬나오베이트 채널 광도파로의 z-축 분극을 주기적으로 $180^{\circ}$ 위상 변화시키는 Ti:PPLN 제작 공정을 검토하고, 개선하였다. 분극반전 공정에 적합한 지그와 Labview 프로그램을 이용하여 전하량 제어시스템을 고안하였다. 분극반전에 필요한 전하량으로부터 분극에 적절한 고전압 펄스와 duty-cycle을 조절하였으며, 분극에 필요한 임계 전압 보다 작은 전압을 인가한 상태에서 누설전류의 변화를 관찰하여 절연파괴 현상을 또한 최소화하였다.

• 한국수정란이식학회지
• /
• 제20권1호
• /
• pp.25-33
• /
• 2005

본 연구는 가축유전자원의 효율적 보존방법의 개발을 위해 수행되는 체외 정자 세포 생산 연구의 일부로, 생산된 정자 세포의 발생능을 검사하기 위한 체외배양 시스템을 확립 할 목적으로 수행되었다. 성숙 배양시간을 48시간으로 하여 $7\%$ ethanol로 활성화처리한 후 TCM199에 $10\%$의 소 태아 혈청으로 배양하였을 때 배반포까지 발달하지 못하였으나, NCSU23에 $0.4\%$ 소 혈청 알부민으로 배양하였을 때 $3\%$의 활성화된 난모세포가 배반포기까지 발달하였다. 성숙시간을 연장하여 48, 52, 56, 60, 64, 68, 그리고 72시간까지 성숙배양을 실시한 후 $7\%$ 에탄올로 활성화 처리하여 $NCSU23+0.4\%$ BSA로 배양하였을 때 56시간부터 68시간까지 배발달율이 증가하였으나 72시간 성숙배양할 때 배발달율이 다시 저하하여 활성화와 세포질 퇴행간의 윈도우가 56시간부터 68시간 사이인 것으로 추정되었다. 전기자극의 강도를 1, 1.2, 1.4, 1.6, 1.8 그리고 2.0kV/cm로 난모세포를 활성화 처리하였을때 1회 통전으로는 적절한 활성화가 일어나지 않았으며 1.6kV/cm, $80{\mu}s$, 2회 통전이 본 실험조건에서 가장 높은 배발달율을 보였다. 난모세포를 인위적으로 활성화하는데 주로 이용되는 $7\%$ 에탄올법, 전기자극법, 그리고 calcium ionophore법을 직접적으로 비교하였을 때 $7\%$ 에탄올법이 $15.7\%$, 전기 자극법이 $9.5\%$, calcium ionophore법이 $5.8\%$의 배반포 발달율을 보여, 본 실험조건에서는 $7\%$ 에탄올법이 배 발달을 활성화시키는데 가장 효율적인 것으로 나타났다.

• 전력전자학회논문지
• /
• 제21권5호
• /
• pp.396-403
• /
• 2016

Usually, large-sized buses and trucks have a very high load. In addition, frequent braking during downhill or long-distance driving, causes the conventional method using the brake friction to have a problem in safety because of brake fade and brake burst phenomenon. Auxiliary brakes dividing the braking load is essential. Hence, environment-friendly auxiliary brakes, such as contactless brake rather than the engine auxiliary brake system are needed. A study aimed at improving the energy efficiency by recharging electric energy with changing mechanical to electrical energy that occurs when braking is actively in progress. In this paper, the voltage control method is utilized to recover the electric energy generated in the electromagnetic retarder instead of the eddy current. To regenerate the braking energy into the electrical energy, the resonant L-C circuit is configured in the retarder. The voltage generated in the retarder is simply modeled as a transformer. However, retarder voltage control in this paper is simulated by modeling the induction generator because this induction generator modeling is more practical than transformer modeling. The changes in the voltage of the resonance circuit, which depends on the switch pulse duration of the control device, were analyzed. A PI controller algorithm to control this voltage is proposed. The feasibility of modeling retarder and voltage controller are shown by using MATLAB Simulink in this paper.

• 한국진공학회지
• /
• 제11권4호
• /
• pp.230-234
• /
• 2002

고온 급속 열처리를 행한 $LiNbO_3Si$/(100) 구조를 가지고 여러 가지 전극을 사용하여 금속/강유전체/반도체 커패시터를 제작하였으며, 제작한 커패시터의 비휘발성 메모리 응용 가능성을 확인하였다. MFS 커패시터의 C-V 특성 곡선에서는 LiNbO$_3$박막의 강유전성으로 인한 히스테리시스 특성이 관측되었으며, 1 MHz C-V 특성 곡선의 축적 영역에서 산출한 비유전율은 약 25 이었다. Pt 전극을 사용하여 제작한 커패시터에서는 인가 전계 500 kV/cm 범위에서 $1\times10^{-8}$ A/cm 이하의 우수한 누설전류 특성이 나타났다. midgap 부근에서의 계면 준위 밀도는 약 $10^{11}\textrm{cm}^2$.eV 이었으며, 잔류분극 값은 약 1.2 $\muC/\textrm{cm}^2$ 였다. Pt 전극과 A1 전극 모두 500 kHz 주파수의 바이폴러 펄스를 인가하면서 측정한 피로 특성에서 $10^{10}$ cycle 까지 측정된 잔류 분극 값이 초기 값과 같았다.

• 한국의학물리학회:학술대회논문집
• /
• 한국의학물리학회 2002년도 Proceedings
• /
• pp.396-399
• /
• 2002

Intense quasi-monochromatic x-ray irradiation from the linear plasma target is described. The plasma x-ray generator employs a high-voltage power supply, a low-impedance coaxial transmission line, a high-voltage condenser with a capacity of about 200 nF, a turbo-molecular pump, a thyristor pulse generator as a trigger device, and a flash x-ray tube. The high-voltage main condenser is charged up to 55 kV by the power supply, and the electric charges in the condenser are discharged to the tube after triggering the cathode electrode. The x-ray tube is of a demountable triode that is connected to the turbo molecular pump with a pressure of approximately 1 mPa. As electron flows from the cathode electrode are roughly converged to the molybdenum target by the electric field in the tube, the weakly ionized plasma, which consists of metal ions and electrons, forms by the target evaporating. In the present work, the peak tube voltage was almost equal to the initial charging voltage of the main condenser, and the peak current was about 20 kA with a charging voltage of 55 kV. When the charging voltage was increased, the linear plasma x-ray source grew, and the characteristic x-ray intensities of K-series lines increased. The quite sharp lines such as hard x-ray lasers were clearly observed. The quasi-monochromatic radiography was performed by a new film-less computed radiography system.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2012년도 추계총회 및 학술대회 논문집
• /
• pp.16-16
• /
• 2012

Mg and its alloys have been of great interest because of their low density of 1.7, 30% lighter than Al, but their wide applications have been limited because of their poor resistances against corrosion and/or abrasion. Corrosion resistance of Mg alloys can be improved by formation of anodic films using anodic oxidation method in aqueous electrolytes. Plasma electrolytic oxidation (PEO) is one of anodic oxidation methods by which hard anodic films can be formed as a result of micro-arc generation under high electric field. PEO method utilize not only substrate elements but also chemical components in electrolytes to form anodic films on Mg alloys. PEO films formed on AM50 magnesium alloy in an acidic fluozirconate electrolyte were observed to consist of mainly $ZrO_2$ and $MgF_2$. Liu et al reported that PEO coating on AM30 Mg alloy consists of $MgF_2$-rich outer porous layer and an MgO-rich dense inner layer. PEO films prepared on ACM522 Mg die-casting alloy in an aqueous phosphate solution were also reported to be composed of monoclinic $Mg_3(PO_4)_2$. $CeO_2$-incorporated PEO coatings were also reported to be formed on AZ31 Mg alloys in $CeO_2$ particle-containing $Na_2SiO_3$-based electrolytes. Magnesium tin hydroxide ($MgSn(OH)_6$) was also produced on AZ91D alloy by PEO process in stannate-containing electrolyte. Effects of $OH^-$, $F^-$, $PO{_4}^{3-}$ and $SiO{_3}^{2-}$ ions and alloying elements of Al and Sn on the formation of PEO films on pure Mg and Mg alloys and their protective properties against corrosion have been investigated in this work. $PO{_4}^{3-}$, $F^-$ and $SiO{_3}^{2-}$ ions were observed to contribute to the formation of PEO films but $OH^-$ ions were found to break down the surface films under high electric field. The effect of pulse current on the formation of PEO films will be also reported.

• 한국항해항만학회지
• /
• 제29권10호
• /
• pp.859-863
• /
• 2005

본 논문은 광범위한 전력제어가 가능하고, PC 직렬통신 방식에 의해 원거리에서 시스템을 ON-OFF할 수 있으며, 시스템의 상태를 모니터링 할 수 있는 선박비상조명시스템의 전력제어특성 개선에 관해 연구한다. 제안된 시스템은 강압형 컨버터, 비상급전회로, 반 브리지 인버터, 형광램프기동회로, 마이크로프로세서 제어 및 멀티통신회로 등으로 구성된다. 실험을 통하여 과전류에 의한 해당 시스템의 정지와 주전원 차단시의 비상전원에 의한 신속한 급전을 확인할 수 있고, 입력전력은 35[$\%$] 범위까지 제어됨을 확인한다. 또한, 원거리에서 원하는 시스템을 ON-OFF 하고, 시스템의 전력, 전압, 전류, 배터리 전압 등의 모니터링도 한다.