• 한국인쇄학회지
• /
• 제26권2호
• /
• pp.1-13
• /
• 2008

Printed mottle of coated paper is one of the most common phenomenon and the most difficult problem in offset printing. Offset printing is processed mainly processed by the attractive properties between water and oil, so all inks for off-printing must work with dampening solution(water). It may cause the emulsion on the printing nip from the printing pressure. This study aimed to investigate the effect of emulsified inks on print mottle from emulsified cyan ink by force with each different IP A contents. We measured the print mottle by densitometer and image analysis method. The emulsified inks also give effect to now properties of inks and it caused more ink transfer rate, however, it caused low density of inks. Moreover the emulsified inks were spreaded to around of dots and cause the thinning density on the non-printing area like print mottle. The results showed that the emulsified inks also cause scumming on the printing result with little mistake of adjusting dampening solution and mostly decreasing dot reproduction. So we could find out the obvious effect of emulsified inks to print mottle.

• Food Science and Biotechnology
• /
• 제15권2호
• /
• pp.207-213
• /
• 2006

The effects of gellan gum (from S. paucimobilis), EPS-CB (exopolysaccharide from S. chungbukensis), and a series of commercial gums (arabic gum, xanthan gum, guar gum, deacyl gellan gum), on the swelling, rheological, and pasting properties of non-waxy rice flour dispersions were investigated. The swelling properties of rice flours in gellan or guar gum dispersion after heating were found to have increased with increasing gum concentrations, but the swelling properties of rice flour/other gum systems decreased with increasing concentrations. The rice flour/gum mixtures showed high shear-thinning flow behavior (n=0.14-0.32), and consistency index (K) was higher in guar gum than other gum dispersions. The initial pasting temperatures and peak times increased along with increasing gum concentration. The peak viscosity of rice flour increased in guar gum and deacyl gellan dispersions, and the breakdown and setback viscosity of the rice flour paste was lowest in the xanthan gum system, but remained higher than those of the control. The apparent viscosities of the rice flour/gellan gum mixture pastes were the highest among the tested combinations.

• Journal of Microbiology and Biotechnology
• /
• 제20권4호
• /
• pp.844-851
• /
• 2010

Controlling the dissolved oxygen (DO) in the fed-batch culture of the medicinal mushroom Ganoderma lucidum led to a 2-fold increase of the maximum biomass productivity compared with uncontrolled DO conditions. By contrast, extracellular polysaccharide (EPS) production was two times higher under oxygen limitation (uncontrolled DO) than under increased oxygen availability (controlled DO). Morphologically, dispersed mycelium was predominant under controlled DO conditions, with highly branched hyphae, consistent with the enhanced culture growth noted under these conditions, whereas in the uncontrolled DO process mycelial clumps were the most common morphology throughout the culture. However, in both cultures, clamp connections were found. This is an exciting new finding, which widens the applicability of this basidiomycete in submerged fermentation. In rheological terms, broths demonstrated shear-thinning behavior with a yield stress under both DO conditions. The flow curves were best described by the Herschel-Bulkley model: flow index down to 0.6 and consistency coefficient up to 0.2 and 0.6 Pa $s^n$ in uncontrolled and controlled cultures DO, respectively. The pseudoplastic behavior was entirely due to the fungal biomass, and not to the presence of EPS (rheological analysis of the filtered broth showed Newtonian behavior). It is clear from this study that dissolved oxygen tension is a critical process parameter that distinctly influences G. lucidum morphology and rheology, affecting the overall performance of the process. This study contributes to an improved understanding of the process physiology of submerged fermentation of G. lucidum.

• 한국재료학회지
• /
• 제27권2호
• /
• pp.107-112
• /
• 2017

The BCBJ (Back Contact and Back Junction) or back-lit solar cell design eliminates shading loss by placing the pn junction and metal electrode contacts all on one side that faces away from the sun. However, as the electron-hole generation sites now are located very far from the pn junction, loss by minority-carrier recombination can be a significant issue. Utilizing Medici, a 2-dimensional semiconductor device simulation tool, the interdependency between the substrate thickness and the minority-carrier recombination lifetime was studied in terms of how these factors affect the solar cell power output. Qualitatively speaking, the results indicate that a very high quality substrate with a long recombination lifetime is needed to maintain the maximum power generation. The quantitative value of the recombination lifetime of minority-carriers, i.e., electrons in p-type substrates, required in the BCBJ cell is about one order of magnitude longer than that in the front-lit cell, i.e., $5{\times}10^{-4}sec$ vs. $5{\times}10^{-5}sec$. Regardless of substrate thickness up to $150{\mu}m$, the power output in the BCBJ cell stays at nearly the maximum value of about $1.8{\times}10^{-2}W{\cdot}cm^{-2}$, or $18mW{\cdot}cm^{-2}$, as long as the recombination lifetime is $5{\times}10^{-4}s$ or longer. The output power, however, declines steeply to as low as $10mW{\cdot}cm^{-2}$ when the recombination lifetime becomes significantly shorter than $5{\times}10^{-4}sec$. Substrate thinning is found to be not as effective as in the front-lit case in stemming the decline in the output power. In view of these results, for BCBJ applications, the substrate needs to be only mono-crystalline Si of very high quality. This bars the use of poly-crystalline Si, which is gaining wider acceptance in standard front-lit solar cells.

• 한국산림과학회지
• /
• 제90권3호
• /
• pp.388-397
• /
• 2001

작업환경의 개선이 불가능한 임업에 있어서 올바른 작업자세는 불필요한 체력의 낭비 및 누적된 특정부위에서 피로로 유발되는 상해발생 예방, 체력 저하로 인한 주의력 감소로 야기되는 휴먼에러 예방 등의 직접적인 효과를 가져 올 수 있을 것으로 판단된다. 이에 본 연구는 OWAS분석기법을 이용하여 체인톱을 이용한 간벌작업, 체인톱을 이용한 피해목벌채작업, 손톱을 이용한 임내정리작업, 낫을 이용한 덩굴제거작업, 고지절단톱을 이용한 가지치기작업, 낫을 이용한 어린나무가꾸기작업에 대하여 작업자세분석을 실시하였다. 주요 작업 중, 체인톱과 낫을 이용한 작업에서 근골격계에 약간의 해를 끼침으로 가까운 시일 내에 작업자세의 교정이 필요한 수준(수준 III)의 코드비율과 근골격계에 매우 심각한 해를 끼침으로 즉각적인 작업자세의 교정을 필요로 하는 수준(수준 IV)의 코드비율이 높게 조사되었다. 체인톱을 이용한 벌목작업에서 미숙련자와 숙련자의 작업자세를 비교해 본 결과, 수준 IV의 경우 중간 수준의 숙련자가 5.1%로 14.1%의 미숙련자 보다 낮은 것으로 조사되었다.

• Tribology and Lubricants
• /
• 제33권3호
• /
• pp.119-125
• /
• 2017

In this study, we perform a numerical analysis to predict the film thickness and lubrication regions for a thrust ball bearing under different operating conditions. Film thinning and replenishment affect the film thickness in starved lubrication. As the inlet meniscus position is brought to the edge of the Hertz contact, the thin film thickness is calculated as starved equation. We use a film replenishment model to determine the recovery film thickness between rolling elements. We use a hydrodynamic model to describe film recovery, that results from the effects of surface tension. In this model, we consider the surface tension gradient in fluid depression as the driving force for fluid recovery. We use Fourier transform method to determine the time-dependent depth of depressed oil. We calculate the change in the central film thickness graphically by using the recovery equation in starved elastohydrodynamic lubrication(EHL) under operating conditions that include numbers of balls, sliding velocity, applied force, and ambient film thickness. We evaluate the degree of starvation by using the distance from the center of the contact area to the meniscus position. Parched lubrication, a phenomenon where the film thickness decreases consistently, occurs at the severe condition. We determine optimal values with respect to the numbers of balls, and sliding velocity. The investigation can contribute to the design operating conditions for proper lubrication.

• Clinical and Experimental Reproductive Medicine
• /
• 제41권2호
• /
• pp.68-74
• /
• 2014

Objective: In search of an ideal method of assisted hatching (AH), we compared the effects of conventional micropipette-AH and laser-AH on the blastocyst formation rate (BFR) and blastocyst cell numbers. Methods: Four-to five-week-old ICR female mice were paired with male mice after superovulation using Pregnant mare's serum gonadotropin (PMSG) and hCG. The two-cell embryos were flushed from the oviducts of female mice. The retrieved two-cell embryos underwent one of five AH procedures: single mechanical assisted hatching (sMAH); cross mechanical assisted hatching (cMAH); single laser assisted hatching (sLAH); quarter laser assisted hatching (qLAH); and quarter laser zona thinning assisted hatching (qLZT-AH). After 72 hours incubation, double immunofluorescence staining was performed. Results: Following a 72 hours incubation, a higher hatching BFR was observed in the control, sMAH, cMAH, and sLAH groups, compared to those in the qLAH and qLZT-AH groups (p<0.05). The hatched BFR was significantly higher in the qLAH and qLZT-AH groups than in the others (p<0.05 for each group). The inner cell mass (ICM) was higher in the control and sMAH group (p<0.05). The trophectoderm cell number was higher in the cMAH and qLAH groups (p<0.05). Conclusion: Our results showed that the hatched BFR was higher in groups exposed the the qLAH and qLZT-AH methods compared to groups exposed to other AH methods. In the qLAH group, although the total cell number was significantly higher than in controls, the ICM ratio was significantly lower in than controls.

• 한국산학기술학회논문지
• /
• 제19권9호
• /
• pp.1-6
• /
• 2018

하이드로포밍 기술은 지난 20년간 자동차부품의 적용을 중심으로 비약적인 발전을 해 왔다. 이 기술은 자동차 산업응용분야에 많은 장점을 가지고 있는데 이는 더 나은 구조적 강건성, 부품수 감소에 기인한 비용절감, 재료절약, 무게감소, 낮은 스프링백현상, 개선된 강도, 내구성 향상, 설계 유연성 등이다. 하이드로포밍 부품의 성형성 검토를 위하여 다양한 컴퓨터 시뮬레이션 기술 등이 발달해 왔으며 이를 통해 성형 가능성을 검토하는 것과 동시에 성형을 위하여 벤딩 공정, 프리포밍공정, 다이클로징 공정 등의 효율적인 공정을 수립하여 하이드로포밍 부품들을 설계하고 있다. 이에 본 연구에서는 하이드로포밍 부품 설계 시 고려사항 중 성형량, 부품의 단면길이(하이드로포밍 프레스 용량에 맞는), 최소 곡률(하이드로포밍 압력에 따른 곡률 영향 평가) 등을 제시하고 실제 자동차용 리어 서브-프레임 부품의 단면분석을 실시함으로써 하이드로포밍 성형을 위한 설계 방안을 제시하고자 한다. 아울러 하이드로포밍 공정인자 중 프리벤딩, 축피딩, 유압 압력, 프레스 하중, 마찰 등의 효과를 분석하여 이들 공정이 직접적인 하이드로포밍 성형에 필요인자 인지 등을 고찰하였다.

• Clinical and Experimental Reproductive Medicine
• /
• 제44권4호
• /
• pp.193-200
• /
• 2017

Objective: This study was conducted to investigate the efficacy of laser-assisted hatching (LAH) and various vitrification times for embryonic development and blastocyst cell numbers. Methods: First, 2-cell and 8-cell embryos were collected by flushing out the oviducts. In the control groups, they were vitrified for 8 or 10 minutes without LAH. The LAH groups underwent quarter laser zona thinning-assisted hatching before vitrification (4, 6, and 8 minutes or 4, 7, and 10 minutes, respectively). After incubation, double-immunofluorescence staining was performed. Results: The hatched blastocyst rate 72 hours after the 2-cell embryos were thawed was significantly higher in the 2LAH-ES8 group (33.3%) than in the other groups (p< 0.05). In the control-8 group ($22.1{\pm}4.6$), the cell number of the inner cell mass was higher than in the LAH groups (p< 0.05). The number of trophectoderm cells was higher in the 2LAH-ES6 group ($92.8{\pm}8.9$) than in the others (p< 0.05). The hatched blastocyst rate 48 hours after the 8-cell embryos were thawed was higher in the 8LAH-ES4 group (45.5%) than in the other groups, but not significantly. The inner cell mass cell number was highest in the 8LAH-ES7 group ($19.5{\pm}5.1$, p< 0.05). The number of trophectoderm cells was higher in the 8LAH-ES10 group ($73.2{\pm}12.1$) than in the other groups, but without statistical significance. Conclusion: When LAH was performed, 2-cell embryos with large blastomeres had a lower hatched blastocyst rate when the exposure to vitrification solution was shorter. Conversely, 8-cell embryos with small blastomere had a higher hatched blastocyst rate when the exposure to vitrification solution was shorter.

• 자원리싸이클링
• /
• 제15권1호
• /
• pp.66-73
• /
• 2006

고정층 마이크로반응기를 이용하여 폐목재의 열화학적 전환에 영향을 미치는 운전 조건들-반응온도, 승온속도, 입도, 수분함량의 영향을 조사하였다. 사용한 시료는 소나무, 참나무, 아카시아, 은행나무의 폐목재칩을 사용하였다. 실험에 사용한 시료의 평균 수분 함량은 $35wt\%$이었으며 다른 바이오매스와 마찬가지로 회분함량은 $0.5wt\%$ 이하로 나타났다. 시료들의 평균 발열량은 4,550kca1/kg이었다. 열화학적 전환에 따라 발생된 생성물분포는 시료종류, 수분함량, 입도와 같이 시료의 물성에 따라 다소 달랐으며 평균적으로 액상 $40wt\%$, 고상 $20wt\%$,그리고 기상 $40wt\%$를 보였다. 생성가스의 조성은 거의 모든 실험변수에 영향을 받았으며, 평균적으로 수소 $40wt\%$, 일산화탄소 $30wt\%$이었으며 메탄은 $10wt\%$ 정도이었다.