• 한국분말재료학회지
• /
• 제18권1호
• /
• pp.41-48
• /
• 2011

As a pore precursor, carbon black with different content of 0 to 60 vol% were added to (Ba,Sr)$TiO_3$ powder. Porous (Ba,Sr)$TiO_3$ ceramics were prepared by pressureless sintering at $1350^{\circ}C$ for 1h under air. Effects of carbon black content on the microstructure and PTCR characteristics of porous (Ba,Sr)$TiO_3$ ceramics were investigated. The porosity of porous (Ba,Sr)$TiO_3$ ceramics increased from 6.97% to 18.22% and the grain size slightly decreased from $7.51\;{\mu}m$ to $5.96\;{\mu}m$ with increasing carbon black contents. PTCR jump of the (Ba,Sr)$TiO_3$ ceramics prepared by adding carbon black was more than $10^5$, and slightly increased with increasing carbon black. The PTCR jump in the (Ba,Sr)$TiO_3$ ceramics prepared by adding 40 vol% carbon black showed an excellent value of $9.68{\times}10^5$, which was above two times higher than that in (Ba,Sr)$TiO_3$ ceramics. These results correspond with Heywang model for the explanation of PTCR effect in (Ba,Sr)$TiO_3$ ceramics. It was considered that carbon black is an effective additive for preparing porous $BaTiO_3$ based ceramics. It is believed that newly prepared (Ba,Sr)$TiO_3$ cermics can be used for PTC thermistor.

• Journal of Microbiology
• /
• 제40권2호
• /
• pp.119-124
• /
• 2002

Experiments for the characterization of inactivation were performed in a series of batch processes with the total coliform used as a general indicator organism based on the chlorine residuals as a disinfectant. The water samples were taken from the outlet of a settling basin in a conventional surface water treat- ment system that is provided with the raw water drawn from the mid-stream of the Han River, The inactivation of total coliform was experimentally analysed for the dose of disinfectants contact time, filtration and mixing intensity. The curves obtained from a series of batch processes were shaped with a general tailing-off and biphasic mode of inactivation, i.e. a sharp loss of bacterial viability within 15 min followed by an extended phase. In order to observe the effect of carry-over suspended solids on chlorine consumption and disinfection efficiency, the water samples were filtered, prior to inoculation with coliforms, with membranes of both 2.5$\mu$m and 11.0 $\mu$m pore size, and with a sand tilter of 1.0 mm in effective size and of 1.4 in uniformity coefficient. As far as the disinfection efficiency is concerned, there were no significant differences. The parameters estimated by the models of Chick-Wat-son, Hom and Selleck from our experimental data obtained within 120 min are: log(N/N$\_$0/)=-0.16CT with n=1, leg(N/N$\_$0/)=-0.71C$\^$0.87/ with n 1 for the Chick-Watson model, log (N/N$\_$0/)=-1.87C$\^$0.47/ T$\^$0.36/ for the Hom model, log (MHo)=-2.13log (1+CT/0.11) for the Selleck model. It is notable that among the models reviewed with regard to the experimental data obtained, the Selleck model appeared to most closely resemble the total coliform survival curve.

• 대한환경공학회지
• /
• 제39권7호
• /
• pp.391-402
• /
• 2017

근래에 미세먼지가 대기환경 관련하여 이슈가 되고 있으며, 초미세먼지의 효과적인 집진을 위하여 대용량화가 용이한 여과집진기가 상업적으로 사용될 수 있는지에 대한 평가가 필요하다. 실험실 규모의 여과집진 장치를 제작하여, PTFE 재질의 부직포 여과백 또는 PTFE membrane이 코팅된 PTFE 재질의 부직포 여과백에서의 미세먼지 집진특성을 파악하기 위하여 집진실험을 수행하였다. 실험 변수로 여과속도, 투입 먼지 농도, 입도분포가 다른 먼지 종류 등을 사용한 실험에서, 여과속도가 낮을수록, 먼지 투입농도가 높을수록, 평균입도가 클수록 집진효율이 높았으며, 여과속도가 높고, 먼지 투입농도가 높을수록 압력손실이 높게 나타났다. Pore size가 상대적으로 작은 PTFE membrane이 코팅된 여과백을 사용한 경우, 코팅이 되지 않은 여과백을 사용한 경우에 비하여 집진효율이 높고, 표면여과에 따른 포집 먼지층 저항계수가 낮아져 압력손실이 낮게 나타났다. PTFE membrane이 코팅된 여과백을 사용하여 off-line 탈진을 수행할 경우, 적정 여과속도 범위 내에서 $PM_{2.5}$에 대한 집진효율이 99.99% 이상으로 매우 높게 유지됨에 따라, 여과집진기를 사용하여 초미세먼지를 효과적으로 집진할 수 있음을 확인하였다.

• 멤브레인
• /
• 제14권4호
• /
• pp.329-338
• /
• 2004

본 연구에서는 4종류의 관형 세라믹 정밀 및 한외여과막(탄소 재질)으로 제지공장의 방류수를 물로 주기적 역세척하면서 여과하였을 때, 최적 역세척 시간을 규명하였다. 각 분리막에 대상으로 물 역세척 시간의 영향을 살펴 본 결과, 분리막의 기공이 클수록 길게 역세척 하는 것이 가장 많은 총여과부피, 즉 처리수의 회수 효율이 높기 때문에 가장 효과적이라 할 수 있다. 한편, 180분 동안 여과하면서 초기투과선속에 대한 투과선속의 변화를 살펴본 결과, 정상운전시간이 길수록 막오염이 많이 진행된 상태이므로 역세척 시간을 길게 해주여야만 막오염을 억제하여 높은 투과선속을 유지할 수 있다는 것을 알 수 있었다. 또한, 막오염의 저항 변화 추이를 관찰하여 최적 물역세척 시간을 규명해 보아도, 투과선속의 변화로부터 얻은 최적 역세척 시간과 거의 동일한 결과를 얻을 수 있었다.

• Asian-Australasian Journal of Animal Sciences
• /
• 제16권2호
• /
• pp.211-216
• /
• 2003

The objective of this study was to determine the degradability of cassava chip (CC), cassava waste (CW), yellow sweet potato (YP), white sweet potato (WP), purple sweet potato (PP), corn meal (CM), and rice bran (RB) using in situ technique. Two ruminally fistulated steers with an average weight of $303{\pm}10kg$ were used to determine in situ degradabilities of DM and OM. Seven feed sources were weighted in nylon bags ($38{\mu}m$ pore size) and incubated ruminally for 1, 2, 4, 6, 8, 12, 24, and 48 h. The results showed that asymptote (a+b) and effective degradability (ED) of DM of energy sources ranked from the highest to the lowest; CC, YP, WP, PP, RB, CW, and CM (99.3, 92.5; 97.6, 87.9; 97.5, 87.9; 97.2, 87.8; 87.5, 63.6; 78.6, 63.0 and 81.7; 59.3, respectively) and for OM asymptote (a+b) and effective degradability (ED) were similar to those of degradation of DM (99.4, 93.4; 98.8, 89.8; 98.5, 89.4; 98.4, 88.1; 92.4, 65.8; 85.1, 66.9 and 83.6, 63.3, respectively). It was concluded that disappearance characteristic of CC was the highest and it may potentially facilitate the achievement of optimal ruminal availability of energy: protein especially with NPN for microbial protein synthesis.

• 멤브레인
• /
• 제28권1호
• /
• pp.62-66
• /
• 2018

본 연구에서는 순수와 유사한 밀도의 세척형 구형 입자를 제작하고 순수 수조 내에서 산기량 및 입자 농도에 따른 입자의 유동 속도를 측정하였다. 세척형 구형 입자 1~3%를 MLSS 8,000 mg/L인 활성슬러지 용액에 주입하고 20 LMH 및 산기량 500 mL/min 조건에서 FR 및 SFCO 모드로 동시에 투과 실험하였다. 사용한 분리막은 유효 막면적이 $90cm^2$, 공칭 세공크기가 $0.4{\mu}m$인 평막이다. 입자 농도가 증가할수록 TMP가 감소하였으며 FR 모드, 입자 농도 2%일 때 가장 효과적인 것으로 확인되었다.

• 멤브레인
• /
• 제25권4호
• /
• pp.320-326
• /
• 2015

본 연구에서는 0.5 wt% 에멀젼형 절삭유 수용액에 평막형 분리막을 침지시키고 대칭 및 비대칭 사인파형 투과유속 연속운전(SFCO) 방식으로 실험하였다. 사용한 정밀여과막은 유효 막면적이 $0.02m^2$이고 공칭 세공크기가 $0.15{\mu}m$이었다. 탁도 기준으로 에멀젼형 절삭유의 99% 이상이 제거되었으며 산기량이 증가할수록 TMP가 낮게 상승하였다. 비대칭형 SFCO 운전방식은 투과유속이 낮은 $10{\sim}15L/m^2{\cdot}h$ 영역에서 대칭형 SFCO 운전방식보다 다소 유리하였다. 하지만, 투과유속이 높은 $25{\sim}30L/m^2{\cdot}h$에서는 대칭형 SFCO 운전이 매우 효과적임을 확인할 수 있었다.

• Journal of Pharmaceutical Investigation
• /
• 제32권1호
• /
• pp.21-26
• /
• 2002

The primary culture of human nasal epithelial cell monolayer was performed on a Transwell. The effect of various factors on the tight junction formation was observed in order to develop an in vitro experimental system for nasal transport studies. Human nasal epithelial cells, collected from human normal inferior turbinates, were plated onto diverse inserts. After 4 days, media of the apical surface was removed for air-liquid interface (ALI) culture. Morphological characteristics was observed by transmission electron microscopy (TEM). A polyester membrane of $0.4\;{\mu}m$ pore size was determined as the most effective insert based on the change in the transepithelial electric resistance (TEER) value as well as the $^{14}C-mannitol$ transport study. The ALI method was effective in developing the tight junction as observed in the further increase in the TEER value and reduction in the permeability coefficient $(P_{app})$ of $^{14}C-mannitol$ transport. Results of the transport study of a model drug, budesonide, showed that the primary culture system developed in this study could be further developed and applied for in vitro nasal transport studies.

• 한국재료학회지
• /
• 제19권7호
• /
• pp.362-368
• /
• 2009

Ti scaffolds with a three-dimensional porous structure were successfully fabricated using powder metallurgy and modified rapid prototyping (RP) process. The fabricated Ti scaffolds showed a highly porous structure with interconnected pores. The porosity and pore size of the scaffolds were in the range of 66$\sim$72% and $300\sim400\;\mu$m, respectively. The sintering of the fabricated scaffolds under the vacuum caused the Ti particles to bond to each other. The strength of the scaffolds depended on the layering patterns. The compressive strength of the scaffolds ranged from 15 MPa to 52 MPa according to the scaffolds' architecture. The alkali treatment of the fabricated scaffolds in an aqueous NaOH solution was shown to be effective in improving the bioactivity. The surface of the alkali-treated Ti scaffolds had a nano-sized fibre-like structure. The modified surface showed a good apatite forming ability. The apatite was formed on the surface of the alkali treated Ti scaffolds within 1 day. The thickness of the apatite increased when the soaking time in a simulated body fluid (SBF) solution increased. It is expected that the surface modification of Ti scaffolds by alkali treatment could be effective in forming apatites in vivo and can subsequently enhance bone formation.

• Restorative Dentistry and Endodontics
• /
• 제23권1호
• /
• pp.379-390
• /
• 1998

In endodontic treatment, calcium hydroxide has been used as intracanal medicament. Although calcium hydroxide should be removed thoroughly before permanent root canal filling, no effective method for its removal has been reported. Because of irregularity of root canal walls, root curvatures and anatomic variations, it is insufficient to remove calcium hydroxide from the canal wall only by mechanical instrumentation Considering the chemical effects of irrigants on calcium hydroxide, $Ca^{++}$ dissolving effect from two calcium hydroxide products is investigated, using dis- tilled water, NaOCl, citric acid and EDTA. Vitapex$^{(R)}$ 0.1g and calcium hydroxide 0.03g were dissolved in distilled water, 5% NaOCl, 50% citric acid and 17% EDTA respectively, at 1, 3, 5, 10min. time interval. The solution was filtered using filter paper(pore size $5{\mu}m$) and $Ca^{++}$ concentration was determined by ion chromatography. The result were as follows : 1. Distilled water, NaOCl, citric acid and EDTA abstracted more $Ca^{++}$ from calcium hydroxide than Vitapex$^{(R)}$ except NaOCl 1, 5, 10 time interval. 2. EDTA and citric acid abstracted more $Ca^{++}$ from Vitapex$^{(R)}$ and calcium hydroxide than distilled water or NaOCl. The overall result support the view that water-based calcium hydroxide product is easily removed than oil-based calcium hydroxide product and EDTA, citric acid are more effective in $Ca^{++}$ elution than NaOCl or distilled water.