• Applied Chemistry for Engineering
• /
• v.9 no.4
• /
• pp.475-480
• /
• 1998

A study on the electrochemical reduction of uranium (VI) to uranium (IV) was carried out in the mixed phases of an organic phase with uranium (VI) and aqueous phase of nitric acid by use of a highly packed glassy carbon (GC) fiber column electrode system, and a model for in-situ electrolytic stripping of uranium (VI) was suggested. The electrochemical reduction of uranium (VI) occurred faster in organic phase than in aqueous phase of the mixed phases. The uranium stripping yield increased and then became constant with the increase of organic flow rate of the electrolytic system due to the increase of diffusion resistance of uranium ions in the organic phase into the aqueous phase. Aqueous flow rate, on the other hand, didn't affect the total uranium (VI) reduction current in the system. The system combined with electrochemical reduction was confirmed to be much more effective than the simple system without it in stripping uranium.

• Progress in Superconductivity and Cryogenics
• /
• v.16 no.3
• /
• pp.21-25
• /
• 2014

As wireless power transfer (WPT) technology using strongly coupled electromagnetic resonators is a recently explored technique to realize the large power delivery and storage without any cable or wire, this technique is required for diffusion of electric vehicles (EVs) since it makes possible a convenient charging system. Typically, since the normal conducting coils are used as a transmitting coil in the CPT system, there is limited to deliver the large power promptly in the contactless EV charging system. From this reason, we proposed the combination CPT technology with HTS transmitting antenna, it is called as, superconducting contactless power transfer for EV (SUWPT4EV) system. As the HTS coil has an enough current density, it can deliver a mass amount of electric energy in spite of a small scale antenna. The SUCPT4EV system has been expected as a noble option to improve the transfer efficiency of large electric power. Such a system consists of two resonator coils; HTS transmitting antenna (Tx) coil and normal conducting receiver (Rx) coil. Especially, the impedance matching for each resonator is a sensitive and plays an important role to improve transfer efficiency as well as delivery distance. In this study, we examined the improvement of transmission efficiency and properties for HTS and copper antennas, respectively, within 45 cm distance. Thus, we obtained improved transfer efficiency with HTS antenna over 15% compared with copper antenna. In addition, we achieved effective impedance matching conditions between HTS antenna and copper receiver at radio frequency (RF) power of 370 kHz.

• Macromolecular Research
• /
• v.15 no.7
• /
• pp.676-681
• /
• 2007

A process designed to synthesize rigid polyurethane foam (PUF) with insulative properties via the modulation of PUF cell size via the addition of clay and the application of ultrasound was assessed. The blowing agents utilized in this study include water, cyclopentane, and HFC-365mfc, all of which are known to be environmentally-friendly blowing agents. The rigid PUFs were prepared from polymeric 4,4'-diphenylmethane diisocyanate (PMDI) and polyether polyol with a density of $50kg/m^3$. In addition, rigid PUFs/clay nanocomposites were synthesized with clay modified by PMDI with and without the application of ultrasound. The PUF generated using water as a blowing agent evidenced the highest tensile strength. The tensile strength of the PUF/nanocomposites was higher than that of the neat PUF and the strength was even higher with the application of ultrasound. The cell size of the PUF/clay nanocomposites was less than that of the neat PUF, regardless of the type of blowing agent utilized. It appears that the higher tensile strength and lower cell size of the PUF/clay nanocomposites may be attributable to the uniform dispersion of the clay via ultrasonic agitation. The thermal conductivity of the PUF/clay nanocomposites generated with HCFC-141b evidenced the lowest value when PUF/clay nanocomposites were compared with other blowing agents, including HFC-365mfc, cyclopentane, and water. Ultrasound has also proven effective with regard to the reduction of the thermal conductivity of the PUF/clay nanocomposites with any of the blowing agents employed in this study. It has also been suggested that the uniformly dispersed clay particles in the PUF matrix function as diffusion barriers, which prevent the amelioration of the thermal insulation property.

• Restorative Dentistry and Endodontics
• /
• v.26 no.5
• /
• pp.399-408
• /
• 2001

Tooth bleaching has been prevailing recently for its ability to recover the color and shape of natural teeth without reduction of tooth material. However, it has been reported that bleaching procedure adversely affects the adhesive bond strength of composite resin to tooth. At the same time the bond strength was reported to be regained by application of some chemical agents. The purpose of this in vitro study was to investigate the effect of the removal of residual peroxide on the composite- enamel adhesion and also evaluated fracture mode between resin and enamel after bleaching. Sixty extracted human anterior and premolars teeth were divided into 5 groups and bleached by combined technique using of office bleaching with 35 % hydrogen peroxide and matrix bleaching with 10% carbamide peroxide for 4 weeks. After bleaching, the labial surfaces of each tooth were treated with catalase, 70% ethyl alcohol, distilled water and filled with composite resin. Shear bond strength was tested and the fractured surfaces were also examined with SEM. Analysis revealed significantly higher bond strength values. (p＜0.05) for catalase-treated specimens, but water-treated specimens showed reduction of bond strength, alcohol- treated specimens had medium value between the two groups(p＜0.05). The fracture mode was shown that the catalase group and the alcohol group had cohesive failure but the water sprayed group had adhesive failure. It was concluded that the peroxide residues in tooth after bleaching seems to be removed by gradual diffusion and the free radical oxygen from peroxide prevents polymerization by combining catalyst in the resin monomer. Therefore it may be possible to eliminate the adverse effect on the adhesion of composite resin to enamel after bleaching by using water displacement solution or dentin bonding agent including it for effective removal of residual peroxide.

• The Journal of Engineering Research
• /
• v.2 no.1
• /
• pp.139-145
• /
• 1997

The effect of Ba addition on the thermal stabilization of $\gamma$-$Al_2O_3$ powders were studied. Ba additive was introduced into $\gamma$-$Al_2O_3$ powders by wet impregnation of $Ba(No_3)_3$.$6H_2O$. Ba additive was proved to be effective on the thermal stabilization of $\gamma$-$Al_2O_3$ powders by suppression of sintering. The optimum content of Ba was determined by 5 mol%, through the calcinations temperature range. It is suggested that the main reason of thermal stabilizaton is the substitution effect of large $Ba^{2+}$ ions into the $\Al^{3+}$ sites, which suppressed the surface diffusion of $\Al^{3+}$ ions.

• Clean Technology
• /
• v.18 no.2
• /
• pp.123-143
• /
• 2012

Supercritical fluid technology (SFT) is recently one of the most new techniques, which has been interested various fields of related chemical industries. SFT is the most effective and practical technology with eco-friendly, energy-savings, and high efficiency as the technique using the advantages of supercritical fluid such as high solvation power, solubility, mass transfer rate, and diffusion rate. Especially, it is necessary to analyze, evaluate, and develop the potential of application techniques using SFT with these characterizations. Therefore in this review, the phase behavior in supercritical fluid at high temperature and pressure of monomers/polymers for the optimization of polymerization process are briefly described, and the preparation of molecularly imprinted polymers (MIPs) in supercritical fluid using supercritical polymerization and the performance evaluation of MIPs are introduced.

• Journal of the Korean Wood Science and Technology
• /
• v.37 no.3
• /
• pp.265-273
• /
• 2009

The aim of this study was to investigate the antifungal activitiy of extracts from different parts of Cryptomeria japonica against Trichophyton mentagrophytes, Trichophyton rubrum and Microsporum gypseum. Disc diffusion and agar dilution methods were used for determining the antifungal activity of extracts, and their major constituents were analyzed by GC/MS. Black heartwood extract among the extracts showed the highest antifungal activity against dermatophytes. TLC was used for fractionating the effective fraction from the black heartwood extract with n-hexane and chloroform as developing solvents, and then antifungal activity of each fraction was examined against dermatophytes. As a result, seventh fraction showed the highest antifungal activity among nine fractions. The major constituent of the seventh fraction determined by GC/MS was expected to be sesquiterpene, damascone with 2 more carbon atoms. The other constituents were also identified as elemol, eudesmol and hinokione.

• Korean Journal of Materials Research
• /
• v.11 no.5
• /
• pp.431-437
• /
• 2001

This research was examined the effect of intercritical heat treatment on the mechanical Properties and retained austenite formation in 0.1C-6.5Mn steels for the development of a high strength high ductility steel. using of transformation induced plasticity due to retained austenite. The stability of retained austenite is very important for the good ductility and it depend on diffusion of carbon and manganese during reverse transformation. It is effective to heat treat at$ 645^{\circ}C$ in order to obtain over 30 vol.% of retained austenite. However, it is more desirable to heat treat at $620^{\circ}C$, considering the volume fraction and mechanical stability of retained austenite. The strength-elongation combination in cold rolled steel sheets after reverse transformed at $620^{\circ}C$ for 1hr was about 4000k9/mm7, but it decreased rapidly with increasing holding time at high temperature due to the decrease of ductility. The addition of 1.1%Si in 0.14C-6.5Mn TRIP steel does not improve the mechanical properties and retained austenite formation.

• Journal of Pharmaceutical Investigation
• /
• v.36 no.5
• /
• pp.321-329
• /
• 2006

Albuterol, a selective ${\beta}_2$-adrenergic receptor stimulant, has been introduced as a potent bronchodilator for patients with bronchial asthma, chronic obstructive bronchial disease, chronic bronchitis and pulmonary emphysema. The percutaneous permeation of albuterol sulfate was investigated in hairless mouse skin in vitro with and without pretreatment with enhancers. The enhancing effects of ethanol and various penetration enhancers such as terpenes, non-ionic surfactants, pyrrolidones, and fatty acids on the permeation of albuterol sulfate were evaluated using Franz diffusion cells. Among terpenes studied, 1,8-cineole was the most effective enhancer, which increased the permeability of albuterol sulfate approximately 33-fold compared with the control without enhancer pretrement, followed by d-limonene with enhancement ratio of 21.79. 2-Pyrrolidone-5-carboxylic acid increased the permeability of albuterol sulfate approximately 5.5-fold compared with the control. Other pyrrolidones tested showed only slight permeability enhancing effect with enhancement ratio less than 2.8. Nonionic surfactants showed moderate enhancing effects. Lauric acid increased the permeability of albuterol sulfate approximately 30-fold with decreasing the lag time from 2.85 to 0.64 hr. Oleic acid and linoleic acid showed enhancement ratio of 24.55 and 22.91, respectively. These findings would allow a more rational approach for designing formulations for the transdermal delivery of albuterol sulfate and similar drugs.

• Journal of Pharmaceutical Investigation
• /
• v.29 no.4
• /
• pp.329-335
• /
• 1999

Clenbuterol, a selective ${\beta}_2-adrenergic$ receptor stimulant, has been introduced as a potent bronchodilator for patients with bronchial asthma, chronic bronchitis and pulmonary emphysema. For the purpose of developing a transdermal preparation for clenbuterol, we attempted to select an optimal solvent system and permeation enhancer among fatty acids and fatty alcohols which are known to accelerate the penetration of various drugs in permeation experiments using hairless mouse skin and Franz diffusion cell. Apparent partition coefficient of clenbuterol was increased as pH of buffer solution was increased and solubility of clenbuterol was increased as the percent of propylene glycol(PG) in buffer solution(pH 10) was increased. Permeability of clenbuterol from different buffer(pH 10)/PG solvent mixtures was decreased as the percent of PG in pH 10 buffer solution was increased and among the various enhancers studied, lauryl alcohol was found to be the most effective enhancer, increasing the permeability of clenbuterol approximately 76-fold compared with control. Lauryl alcohol$(0{\sim}2%)$ enhanced the permeability of clenbuterol concentration-dependently. In this study, the optimal solvent system for the penetration of clenbuterol was found to be 50/50 buffer(pH 10)/PG solvent mixture containing 2% lauryl alcohol.