• Korean Journal of Materials Research
• /
• v.12 no.7
• /
• pp.533-539
• /
• 2002

Porous anodic aluminum oxide layer for nano templates was prepared in acidic solutions. In order to investigate effects of 2nd anodization on ordered formation behaviors of the porous oxide layers, electrochemical and microstructural studies were performed, primarily using TEM, FE- SEM, AFM, and Ultramicrotomy. The pore diameter of the anodic oxide layer increased approximately linearly with increasing voltages, and to the contrary, the pore density decreased. It was shown that 2nd anodizing on the cell base after dissolving 1st anodic oxide layer was remarkably effective for forming ordered array of the pores, comparing with the case for 1st anodization only. And for controlling the diameter of pores, widening method by chemical dissolution seemed more practical than by electrochemical methods.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.50 no.3
• /
• pp.318-325
• /
• 2014

The main object of this study is to investigate the collection characteristics of wet-type rotating porous disk system experimentally. The experiment is carried out to analyze the pressure drop and collection efficiency for the present system with the experimental parameters such as system inlet velocity, stage number, tube diameter, inlet concentration, etc. In results, for the present system, at 5 stage and ${\upsilon}_{in}=1.8m/s$, the pressure drop becomes significantly lower as $64mmH_2O$ in comparison with that of the conventional wet type scrubber (Venturi scrubber, over $250mmH_2O$). The collection efficiencies increase with higher inlet velocity showing 92, 95.7, 98.4%, while $SO_2$ removal efficiencies decrease with increment of inlet velocity as 80, 65, 50% at ${\upsilon}_{in}=1.08$, 1.44, 1.8 m/s and tube diameter $D_t=10mm$, respectively. The present system is to be considered as an effective compact system for a simultaneous removal of particle/gas phase pollutants from marine diesel engines.

• Computers and Concrete
• /
• v.16 no.2
• /
• pp.311-327
• /
• 2015

Employing discrete elements for considering bond-slip effects in reinforced concrete structures is very time consuming. In this study, a new modified embedded element method is used to consider the bond-slip phenomenon in structural behavior of reinforced concrete structures. A comprehensive parametric study of RC slabs is performed to determine influence of different variables on structural behavior. The parametric study includes a set of simple models accompanied with complex models such as multi-storey buildings. The procedure includes the decrease in the effective stiffness of steel bar in the layered model. Validation of the proposed model with existing experimental results demonstrates that the model is capable of considering the bond-slip effects in embedded elements. Results demonstrate the significant effect of bond-slip on total behavior of structural members. Concrete characteristic strengths, steel yield stress, bar diameter, concrete coverage and reinforcement ratios are the parameters considered in the parametric study. Results revealed that the overall behavior of slab is significantly affected by bar diameter compared with other parameters. Variation of steel yield stress has insignificant impact in static response of RC slabs; however, its effect in cyclic behavior is important.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.12 no.3
• /
• pp.227-234
• /
• 2000

An experimental study was performed for understanding the limiting power and heat transfer characteristics of an MHP having the diameter of 3 or 4 mm which could be applied to cooling of miniature electronic equipment such as the notebook PC CPU etc. The experimental parameters which are inclination, structure of the wick, the length of the condenser and the total heat pipe were considered. The MHP with a woven-wired wick has the advantages of the improvement in capillary limit, the effective attachment tightly toward wall and the convenience in construction of wick. Cooling performance of the present MHP was compared with that of MHP with grooved, fine fiber and sintered type wick which were applied by existing enterprises. With respect to the inclination of$ -5^{\circ}$ , an MHP having the diameter of 3 or 4 mm shows the limiting power of 6~14 W. Therefore, it is expected that the MHP of the present study has sufficient applicability of cooling of notebook PC of which the amount of heat generated is about 12 W.

• Archives of Plastic Surgery
• /
• v.46 no.1
• /
• pp.46-56
• /
• 2019

Background When performing lymphovenous anastomosis, it is sometimes difficult to find venules in the proximity of an ideal lymphatic vessel that have a similar diameter to that of the lymphatic vessel. In this situation, larger venules can be used. Methods The authors evaluated the efficacy of and patient satisfaction with lymphovenous bypass with sleeve-in anastomosis. Between January 2014 and December 2016, we performed this procedure in 18 patients (eight upper extremities and 10 lower extremities) with secondary lymphedema. Lymphovenous bypass with sleeve-in anastomosis was performed under microscopy after injecting indocyanine green dye. The circumferential diameter was measured before lymphovenous bypass and at 1, 2, and 6 months after the procedure. An outcomes survey that included patients' qualitative satisfaction with lymphovenous bypass was conducted at 6 months postoperatively. Results Almost all patients showed quantitative improvements after surgery. The circumferential reduction rate in patients with stage II lymphedema of both the upper and lower extremities was significantly greater than in their counterparts with stage III/IV lymphedema. The circumferential reduction rate was lower in lower-extremity patients than in upper-extremity patients. Conclusions Lymphovenous bypass surgery with sleeve-in anastomosis in lymphedema patients is beneficial, and appears to be effective, when adequately-sized venules cannot be found in the proximity of an ideal lymphatic vessel.

• Korean Journal of Chemical Engineering
• /
• v.35 no.11
• /
• pp.2157-2163
• /
• 2018

Catalytic reactors have been essential for chemical engineering process, and different designs of reactors in multi-scales have been previously studied. Computational fluid dynamics (CFD) utilized in reactor designs have been gaining interest due to its cost-effective advantage in designing the actual reactors before its construction. In this work, butadiene synthesis via oxidative dehydrogenation (ODH) of n-butene using tubular reactor was used as a case study in the CFD model. The effects of coolant and reactor diameter were investigated in assessing the reactor performance. Based on the results of the CFD model, the conversion and selectivity were 86.5% and 59.5% respectively in a fixed bed reactor under adiabatic condition. When coolants were used in a tubular reactor, reactor temperature profiles showed that solar salt had lower temperature gradients inside the reactor than the cooling water. Furthermore, higher conversion (90.9%) and selectivity (90.5%) were observed for solar salt as compared to the cooling water (88.4% for conversion and 86.3% for selectivity). Meanwhile, reducing the reactor diameter resulted in smaller temperature gradients with higher conversion and selectivity.

• Korean Journal of Metals and Materials
• /
• v.49 no.4
• /
• pp.291-297
• /
• 2011

This work investigated the microstructure and mechanical properties of 6063 Al alloy fabricated by shear-drawing (SD) technique where shear and drawing strains were combined together within a predetermined die. To find the optimum condition for sound deformation, three different dies having different inner angle and diameter of the exit channel were prepared. After single deformation of the present sample, the sound deformation took place without an abrupt failure of the sample if the inner angle would be greater than $135^{\circ}$ in this study, when the channel diameter of the SD die was reduced from 10 to 9 mm. Microstructural observation showed that the inner angle of $135^{\circ}$ was found to be more effective than that of $150^{\circ}$ in terms of the alignment of each grain to the shear direction imposed by SD method. In addition, the yield strength of the SD-deformed sample was twice higher than that of the initial counterpart while loosing ductility in tension.

• Journal of Environmental Science International
• /
• v.32 no.3
• /
• pp.161-171
• /
• 2023

The present study evaluated growth factors affecting oak community plantations through literature review and a field survey. Specifically, 41 related literature sources were analyzed and field surveys were conducted to collect growth data. Previous studies were analyzed to identify variables with high frequency of use. The frequency of use was in the order of tree size > environment > planting density > forest age. Analysis of factors impacting height and diameter growth revealed that the growth rate of species other than Quercus variabilis was negative in the field survey. This may be because of differences between the actual trees planted and specifications in the construction drawings, which may be attributed to the site conditions and decisions made by the project subject during construction. Furthermore, simple linear regression analysis was conducted with time, height at planting, density, and species code as the independent variables and growth rate as the dependent variable. A strong positive linear correlation was noted between height and diameter. This work builds a foundation for developing a forest restoration model and simulation program based on a regression model derived from the four variables tested.

• Horticultural Science & Technology
• /
• v.33 no.6
• /
• pp.812-819
• /
• 2015

Gladiolus is one of the most popular cut flowers in the world floral market and is highly attractive to consumers. The production of poor-quality gladiolus spikes is one of the most important hurdles to obtaining high prices for this crop. The main objectives of this study were to improve the quantitative characteristics of gladiolus spikes, to increase propagule production and to enhance chemical constituent levels in leaves to help improve plant growth. We performed foliar application of bioregulators, including polyamines (putrescine and spermine) and vitamins (ascorbic acid and thiamine), at different concentrations (0, 0.1, 0.4, 0.7 and 1 mM) to gladiolus plants at the three leaf, five leaf and slipping stages. Application of 1 mM putrescine was the most effective treatment, with prominent effects on economically important spike traits including spike length (55.53 cm), spike diameter (7.53 mm), florets per spike (13.99), first floret diameter (9.66 cm) and first floret weight (4.90 g), followed by spermine treatment. The 1 mM putrescine treatment also had positive effects on corm-associated traits including corm diameter and corm weight, with values of 4.57 cm and 26.16 g compared to 3.47 cm and 17.16 g in control plants, respectively. The contents of chemical constituents in leaves, including total chlorophylls ($8.06mg{\cdot}g^{-1}$), total carotenoids ($1.66mg{\cdot}g^{-1}$), total soluble sugars ($4.75 mg{\cdot}g^{-1}$) and phenolics ($0.89mg{\cdot}g^{-1}$) increased in response to foliar application of 1 mM putrescine compared to the control. Ascorbic acid and thiamine also had positive effects on various plant morphological traits and chemical constituents in leaves compared to control plants, but the growth-promoting effects of polyamines were more pronounced. Hence, applying polyamines to gladiolus leaves will help improve spike production and increasing propagule (cormel) yields.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.6D
• /
• pp.637-643
• /
• 2012

This research collected work drilling report of TBM method site developed by WRITH company to TBM equipment company in Germany and analyzed work operating productivity. Based Oil the data analyzed TBM operating productivity, This research derived and presented excavation speed (m/day) by TBM diameter (3.0m, 3.5m, 3.8m) and rock. Also, based on the excavation speed (m/day) by TBM diameter, This research estimated a day direct construction cost and total direct construction costs by applying a direct construction cost which spent on per 1m. When we perform a similar geological construction in the future, excavation speed and direct construction cost which were derived by TBM diameter and rock is thinking the effective utilization data to estimate construction cost and plan schedule management before the start of construction.