• Journal of Chest Surgery
• /
• v.21 no.1
• /
• pp.10-16
• /
• 1988

Ten patients with tetralogy of Fallot were studied angiocardiographically before a modified Blalock-Taussig shunt and again 25*3.2 months after the previous shunt. All of ten patients had patent previous shunt at the time of follow up examination. Pre-and postoperative diameters of left and right pulmonary artery and descending aorta were measured and pulmonary artery index [the sum of the crossectional areas of the right and left pulmonary arteries standardized by the body surface area] was calculated. The ratio of mean diameter of left and right pulmonary arteries to the diameter of the descending aorta [LPA+RPA/2xDA] was increased postoperatively by 0.20*0.068 [p=0.020]. Mean PAI [pulmonary artery index] increased from 283.8*178.4 mm/m2 BSA to 345.8~144.5 mm/m2 BSA after shunt operation [p=0.019]. This results suggested that the modified Blalock-Taussig shunt was effective to help growth of the pulmonary arteries in most cases of the study populations but the ones with the PAI>233mm*/m* BSA appeared less benefited by Blalock Taussig shunt. Calculation of PAI could be an aid to making a decision whether to perform a one stage corrective surgical procedure or a palliative shunt procedure in the patient with small pulmonary arteries.

• Fisheries and Aquatic Sciences
• /
• v.16 no.3
• /
• pp.211-220
• /
• 2013

A shaking motion could be used to improve fish escapement from a cod-end net by creating a sieving effect over the swept volume or by disturbing the optomotor response of the fish. In this study, a perpendicular shaking motion was generated in a towed cod-end net by a circular canvas attached to the end of the codend, which formed a biased cap-like shape. This concept was tested by using a model in a flow tank and by towing a prototype cod-end during sea trials. For the model tests, the amplitude of the shaking motion was $0.6{\pm}0.1$ times the rear diameter of the cod-end, and the period of the shaking motion was $2.6{\pm}0.1$ s at a flow velocity of 0.6 or 0.8 m/s. In the sea trials, the amplitude was $0.5{\pm}0.2$ times the rear diameter of the cod-end, and the period of the shaking motion was $7{\pm}4$ s at towing speeds of 1.2 or 1.7 m/s. Thus, the shaking amplitude during the sea trials was equal to or less than that observed in the tank tests, and the shaking period was twice as long. The shaking motion described by the amplitude and period could be an effective means to stimulate fish escapement from cod-end during fishing operations considering the response of the fish.

• Transactions of Materials Processing
• /
• v.19 no.6
• /
• pp.329-336
• /
• 2010

Ring forging process is more appropriate for high-length and thin walled ring, because it utilizes the forging press and hence does not require heavy-duty ring rolling mill. Although ring forging process is very simple and economic for facilities, the process is not efficient because of multi-forging-step and low material utilization. An effective ring forging process is developed using a hollow ingot. When a hollow ingot is used with a workpiece, the ingot can be forged into a final ring without multi-stage pre-forging process, such as, cogging, upsetting, and piercing, etc.. Finally it has advantages of the material utilization and process improvement because a few reheating and forging process are not necessary to make workpiece for ring forging. The important design variables are the applied plastic deformation energy to eliminate cast structure and make uniform properties. In this study, the mechanical properties after forging of hollow cast ingot were investigated from the experiment using circumferential sectional model. Also, the effects of process variables were studied by FEM simulation on the basis of thermo-visco-plastic constitutive equation. Applied strain is different at each position in length direction because diameter of hollow ingot is different in length direction. The different strain distribution become into a narrow gap by additional plastic deformation during diameter extension process.

• Journal of the Korean Home Economics Association
• /
• v.40 no.12
• /
• pp.119-129
• /
• 2002

This research aims at finding out situation on purchasing clothes for kids, size recognition and fitting to provide basic data in order to establish standard sizes for kids' clothes. A survey was conducted to 360 mothers who have children ranging from first to third grade in elementary school on clothes purchasing method, wearing situation, criteria in deciding size and fitting preference. In terms of data analysis, frequency, percentage, mean, $X^2$-test, ANOVA and Duncan-test were used via SPSS PC program. The result is as follows; 1. While the recognition on brand was high, the recognition on body size was low: as a result, it is believed that it would be effective to mark the weight along with the brand. 2. Many times, they would select one or two size bigger on all items and they would go for a regular or one that fits as far as filling is concerned showing that it is different from adult clothes. 3. As far as obese kids, they would choose based on the diameter, so the diameter item is right but they are too long in general. The length question should be given special attention when manufacturing clothes for obese kids.

• Wind and Structures
• /
• v.14 no.1
• /
• pp.35-53
• /
• 2011

Spherical object in wind is a common scenario in daily life and engineering practice. The main challenge in understanding the aerodynamics in turbulent wind lies in the multi-aspect of turbulence. This paper presents a wind tunnel study, which focuses on the role of turbulence integral length scale ${\Lambda}$ on the drag of a sphere. Particular turbulent flow conditions were achieved via the proper combination of wind speed, orifice perforated plate, sphere diameter (D) and distance downstream from the plate. The drag was measured in turbulent flow with $2.2{\times}10^4{\leq}Re{\leq}8{\times}10^4$, $0.043{\leq}{\Lambda}/D{\leq}3.24$, and turbulence intensity Tu up to 6.3%. Our results confirmed the general trends of decreasing drag coefficient and critical Reynolds number with increasing turbulence intensity. More interestingly, the unique role of the relative integral length scale has been revealed. Over the range of conditions studied, an integral length of approximately 65% the sphere diameter is most effective in reducing the drag.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.9 no.1
• /
• pp.81-86
• /
• 2010

This paper investigated into process characteristics of AlTiN coated layers for machining to the direction of upper and lower in plastic mold material (KP-4) with the cemented carbide ball endmill with the diameter of 8mm coated AlTiN layers (1~4) step by step using machining center. The material used in experiments was KP-4 that was machined by three types of inclined angles; $15^{\circ}$, $30^{\circ}$ and $45^{\circ}$ As estimated mechanical properties of AlTiN coated layers, it was shown the most result in the condition of three layered coating that the coating that the coating depth, the hardness of the coated layer and the surface roughness of the coated layer were $13{\mu}m$, Hv 3027.3 and $0.042{\mu}m$, respectively. The cutting component was better at the condition of upper direction than that of lower direction in all experimental conditions and indicated to be less which the bigger angle of the material was increased the effective diameter of the tool.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.6
• /
• pp.66-72
• /
• 2014

Incremental forming is a relatively novel sheet forming process, in which parts can be formed without the use of dedicated dies. In this paper, the influence of the process parameters (tool diameter, step size, feed rate, existence of a die, forming methods, and kinds of tool path) on surface roughness in the case in which parts are processed by incremental forming was discussed. Al 1050 material is used in the experiments. A table of orthogonal arrays is used to design the experiments and the ANOVA method is employed to statistically analyze the results. The obtained results show that the process parameters of tool diameter, step size, and the existence of a die have a significant effect on the surface roughness, whereas the feed rate, forming methods and kinds of tool path are insignificant.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.6 no.1
• /
• pp.11-18
• /
• 1996

Grown-in defects like OISF and FPD in the large diameter(> 8 inch)of silicon crystal are characterized. It was revealed that the presence of the ring-patterned OISF would deterorate the minority life time of the silicon crystal. Through the cooling experiment from the $1250^{\circ}C$, the nucleation of the OISF was confirmed to follow the homogeneous nucleation and growth process. In addition to OISF nucleus, crystal originated particle, which was known to be closely related with FPD (Flow Pattern Defects), was found to depend on the pulling rate of the crystal. Combination of the lower rate of the pulling and the faster cooling near the $950^{\circ}C$ is proposed to be effective method in reducing the generation of these grown-in defects.

• Journal of Navigation and Port Research
• /
• v.29 no.9
• /
• pp.783-788
• /
• 2005

This study provided the status and efficiency of the domestic wastewater sea outfalls based on the previous numerical and experimental studies for the analysis of the buoyant discharges from Rosette diffuser in shallow water. The VISJET model and the hybrid model proposed by Kim (2002) can be proper models for the domestic sea outfalls. The experimental results show that the merging height for MBR and MIR depends on the riser diameter and spacing between risers, and the bending characteristics of the buoyant discharges in still ambient water have significant impacts on the dilution. The current wastewater outfall systems in Korea are not effective for the environmental aspect due to the low discharge water depth. The strategies to reduce the contamination near the domestic wastewater outfalls were found to require the sufficient discharge water depth, proper diffuser location considering the tidal currents, enough riser diameter, and sufficient spacing between risers.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.5
• /
• pp.121-129
• /
• 2006

An Intake Port of SI engines plays a key role on improving engine performance by maximizing full load volumetric efficiency or by optimizing in-cylinder air motion. However, designing an intake port has been usually performed based on port experts' experience and know-how, which means that analytical analyses are relatively insufficient. In this paper, port design parameters which decide an overall port shape were defined in order to correlate them relevantly with flow test results accumulated so far. Test species were composed of all twenty eight SI engines which cover major engine displacements from 1,000cc to 4,000cc. First, they were tested on a steady state flow test rig to find out their flow coefficients. Secondly, those flow coefficients were analyzed based on the port design parameters measured from the engines. The most effective parameters were port height, valve head diameter, and the ratio of port size and cylinder bore diameter. The final correlation equation could predict flow coefficients within 2% deviation.