• Bulletin of the Society of Naval Architects of Korea
• /
• v.22 no.1
• /
• pp.31-37
• /
• 1985

In ship's structure, deck and bottom plate are main strength member subjected to the inplane load due to longitudinal bending, i.e. tensile and/or compressive load. The deck and bottom plate are subdivided into many plate members by stiffeners and girders longitudinally and transversely. Since the plate members are thin, it is likely to be collapsed under compressive load, and when we consider the local strength of deck and bottom, the plate members play an important role in the longitudinal strength. Therefore the precise analysis of their compressive ultimate strength is required for the optimal design of ship's structures. In this paper, the modified analytical method using the incremental form of principle of virtual displacement is introduced to determine the compressive ultimate load of plate members. The results by the present method is satisfactory, and the present method is more effective and economical than the finite element method.

• KIEAE Journal
• /
• v.7 no.3
• /
• pp.89-96
• /
• 2007

The purpose of this experimental study is to investigate the compressive strength, shear strength, bending strength, and crack control by the mixture of the hwang-toh. The size of compressive specimens is $200{\times}200{\times}400(mm)$, and the size of shear, bending specimens is $200{\times}200{\times}600(mm)$. Finally, crack control specimens for comparative comparison is $200{\times}200{\times}15(mm)$. The mixture of the hwang-toh is as follows; Hwangtoh( H)+Water(W), H+W+Sand(S), H+W+S+sTraw(0.5%), H+W+S+sT(1.0%). The actual height, width, and the length are measured at the center of all specimens. The main parameters are mixture ratio of hwang-toh, straw and age of specimens. The test results are as follows. (1) The compressive strength is linearly increased until 15 weeks according to specimen ages. (2) About crack control, the specimen added in 1% straw is the most effective.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.10a
• /
• pp.241-246
• /
• 2000

In the strut-tie model design of structural concrete, the importance of the effective strength of concrete strut has been overlooked by many practitioners. The authors believe that the effective strength of concrete strut is an important factor not only in determining steel tie forces but also in verifying the nodal zone strength and geometric compatibility condition of a selected strut-tie model. This study evaluate the effect of the effective strength of concrete strut on structural concrete design by applying the different effective strut strengths to the strut-tie model design of a post-tensioned anchorage zone and a continuous concrete deep beam.

• Journal of Korean Association for Spatial Structures
• /
• v.23 no.2
• /
• pp.69-78
• /
• 2023

This paper investigates the effects of aspect ratio and volume fraction of hooked-end normal-strength steel fibers on the compressive and flexural properties of high-strength concrete with specified compressive strength of 60 MPa. Three types of hooked-end steel fibers with aspect ratios of 64, 67 and 80 were considered and three volume fractions of 0.25%, 0.50% and 0.75% for each steel fiber were respectively added into each high-strength concrete mixture. The test results indicated that the addition of normal-strength steel fibers is effective to improve compressive and flexural properties of high-strength concrete but fiber aspect ratio had little effect on the modulus of elasticity and compressive strength. As steel fiber content and aspect ratio increased, flexural beahvior of notched high-strength concrete beams was effectively improved.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2016.05a
• /
• pp.143-144
• /
• 2016

The core drilling method is considered to be the most effective and common method of assessing the compressive strength of concrete in existing reinforced concrete buildings for structural repair and retrofit. In general, core specimens within reinforcing bars are not permitted in the regulations with regard to assessing concrete strength even if the core specimens can contain the bars in some cases. The purpose of this study is to investigate the effects of the reinforcement arrangement on the concrete compressive strength as a basic research to propose the quantitative criteria of strength for core specimens containing reinforcements. To complete the basic research, cylinder specimens inserted in a variety of reinforcement arrangements were prepared and tested.

• Food Science and Preservation
• /
• v.7 no.1
• /
• pp.63-67
• /
• 2000

Changes in the compressive strength of four typical corrugating mediums (K$_2$A, AS and S) as affected by relative humidity conditions were compared and their relative cost effectiveness was analysed. All mediums lost their compressive strength as relative humidity increased. at the relative humidity of 93% , As medium lost 58% of its initial strength while S medium did about 40%. Calculations of compress factor and compress factor by price indicated that $K_2$ medium was the most cost effective and maintained the highest compressive strength among the mediums tested. It was recommended that $K_2$ medium could be effectively used to make corrugated fiberboard especially for fresh agricultural product packaging .

• Korean Journal of Materials Research
• /
• v.22 no.9
• /
• pp.494-498
• /
• 2012

Geopolymer cements and geopolymer resins are newly advanced mineral binders that are used in order to reduce the carbon dioxide generation that accompanies cement production. The effect of additives on the compressive strength of geopolymerized class-F fly ash was investigated. Blast furnace slag, calcium hydroxide($Ca(OH)_2$), and silica fume powders were added to fly ash. A geopolymeric reaction was initiated by adding a solution of water glass and sodium hydroxide(NaOH) to the powder mixtures. The compressive strength of pure fly ash cured at room temperature for 28 days was found to be as low as 291 $kgf/cm^{-2}$, which was not a suitable value for use in engineering materials. On the contrary, addition of 20 wt% and 40 wt% of blast furnace slag powders to fly ash increased the compressive strength to 458 $kgf/cm^{-2}$ and 750 $kgf/cm^{-2}$, respectively. 5 wt% addition of $Ca(OH)_2$ increased the compressive strength up to 640 $kgf/cm^{-2}$; further addition of $Ca(OH)_2$ further increased the compressive strength. When 2 wt% of silica fume was added, the compressive strength increased to 577 $kgf/cm^{-2}$; the maximum strength was obtained at 6 wt% addition of silica fume. It was confirmed that the addition of CaO and $SiO_2$ to the fly ash powders was effective at increasing the compressive strength of geopolymerized fly ash.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.04a
• /
• pp.265-268
• /
• 1999

In this study, we manufactured the ultra-high strength concrete using mineral admixture which is easily workable. From the test results of compressive strength, It is concluded that the proper replacement ratio of silica fume should not exceed to 10% and the replacement of slag is more effective that the replacement of fly ash to gain very high compressive strength. Thermal stress analysis is conducted to find the way of controlling the thermal crack of ultra-high strength concrete. As results of thermal stress analysis, it was found that reducing placing temperature of concrete(pre-cooling) is effective to reduce thermal crack and placing concrete in high air temperature is more effective than placing concrete in low air temperature.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1992.10a
• /
• pp.100-105
• /
• 1992

While there are many researches in high-strength concrete recently, average strength required is the level of 400kg/$\textrm{cm}^2$ 28days compressive strength yet. For the effective using of high strength concrete, high strength concrete of 600 to 800kg/$\textrm{cm}^2$ 28days compressive strength must be accepted, But in this high strength concrete, due to much cement content, there are the problems of high hydration heat, high viscosity and economical efficiency. To solve these problems, it is suggested the method that replacement some of cement content as flyash up-to-dately. Therefore, the aim of this study is to develop high strength concrete of 800kg/$\textrm{cm}^2$ 28days compressive strength containing fly ash. This paper is the part I that analyze the testing results of fresh concrete in various aspects.

• Computers and Concrete
• /
• v.12 no.4
• /
• pp.499-518
• /
• 2013

Fiber reinforced polymer (FRP) jackets have been widely used as an effective tool for the strengthening and rehabilitation of concrete structures, especially damaged concrete columns. Therefore, a clear understanding of the compressive behavior of FRP-confined concrete is essential. The objective of this paper is to develop a simple efficient method for predicting the compressive strength, the axial strain at the peak stress, and the stress-strain relationship of FRP-confined concrete. In this method, a compressive strength model is established based on Jefferson's failure surface. With the proposed strength model, the strength of FRP-confined concrete can be estimated more precisely. The axial strain at the peak stress is then evaluated using a damage-based formula. Finally, a modified stress-strain relationship is derived based on Lam and Teng's model. The validity of the proposed compressive strength and strain models and the modified stress-strain relationship is verified with a wide range of experimental results collected from the research literature and obtained from the self-conducted test. It can be concluded that, as a competitive alternative, the proposed method can be used to predict the compressive behavior of FRP-confined concrete with reasonable accuracy.