• Membrane Journal
• /
• v.32 no.2
• /
• pp.140-149
• /
• 2022

In this study, the conditions of low temperature and high pressure of biogas upgrading process using polysulfone membrane have been designed and tested to achieve the high recovery and efficiency corresponding to those of the highly selective polymeric materials. Polysulfone hollow fiber membrane with 4-component dope solution was spun via non-solvent induced phase separation. The hollow fiber membrane was mounted into a 1.5 inch housing. The effective area was 1.6 m², and its performance was examined in various operation temperatures and pressures. CO₂ and CH₄ permeances were 412 and 12.7 GPU at 20℃, and 280 and 3.6 GPU at -20℃, respectively, while the CO₂/CH₄ selectivity increased from 32.4 to 77.8. Single gas test was followed by the mixed gas experiments using single-stage and double stage where the membrane area ratio varied from 1:1 to 1:3. At the single-stage, CH₄ purity increased and the recovery decreased as the stage-cut increased. At the double stage, the area ratio of 1:3 showed the higher CH₄ recovery as decreasing the operation temperature at the same purity of CH₄ 97%. Finally, polysulfone hollow fiber membranes have yielded of both CH₄ purity and recovery of 97% at -20℃ and 16 barg.

• Journal of the Korean Society of Safety
• /
• v.37 no.4
• /
• pp.120-128
• /
• 2022

Printed circuit boards (PCBs) are a basic component in the electronics industry and are widely used in nearly all electronic products, such as mobile phones, tablet computers, and digital cameras, as well as in electric equipment. PCB manufacturing involves the use of many chemicals and chemical processes and therefore has more risks than other manufacturing sectors. This study aims to identify the causes of possible accidents during PCB manufacturing through risk assessment, develop and implement safety measures, and evaluate the effectiveness of these measures. Note that the safety measures developed to mitigate the risks of a certain process were also implemented for other similar processes. The risk assessments conducted over seven years, from 2015 to 2021, at a PCB manufacturing company identified 361 hazardous processes. Between 2016 and 2019, 41-56 hazardous processes were identified per year; such processes decreased to fewer than 20 per year after 2020. Application of the risk assessment results to the improvement of the hazardous processes with the similar characteristics seems to be effective in decreasing the risks. Equipment-related factors such as lack of appropriate maintenance, low work standards, and defective protection devices were responsible for 59.8% of all possible accidents. Because PCB manufacturing involves many chemicals, skin contact with hazardous substances, electric shock, fire, and explosion were the most common types of possible accidents (81.7%). In total, 505 safety measures were implemented, including 157 related to purchase and improvement of equipment and devices for safety (31.1%), 147 related to the installation/modification of fire prevention facilities (29.1%), and 69 related to the use of standard electrical appliances (13.7%). Risk assessment conducted after implementing the safety measures showed that these measures significantly decreased risk; 247 processes (68.4%) had a risk level of 3, corresponding to "very low," and 114 processes (31.6%) showed a risk level of 4, corresponding to "low." In particular, risk assessment of 104 processes with risk scores of 12 and 10 other processes with risk score of 16 showed that the risk decreased to 4 after implementing the safety measures. Thus, implementing these measures in similar manufacturing sectors that involve chemical processes can mitigate risk.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.22 no.3
• /
• pp.105-110
• /
• 2022

In line with the trend of the 4th Industrial Revolution, we tried to study the scalability of the craft sector in the art field in the wake of the convergence of new fields through the combination of different fields. To this end, a craft case using 3D printing technology was analyzed based on the theoretical background of the definition and value of digital craft. As a result of the study, craft works using 3D printing technology could be divided into four forms according to the fusion expression method. First, the mixed type was most characterized by harmonious production without significantly deviating from the traditional craft type. Second, the component type was produced in the form in which the characteristics of digital technology, which has advantages of certain shapes and detailed work, were best exhibited. Third, the structural type became a work with analog sensibility by adding traditional craft techniques based on the results output from a 3D printer. Finally, the connection type was the work that showed the greatest glimpse of originality and uniqueness among the analysis cases of this study. As digital technology is positively widely used, future studies will also deal with effective work directions.

• Membrane Journal
• /
• v.32 no.5
• /
• pp.292-303
• /
• 2022

An eco-friendly energy conversion device without the emission of pollutants has gained much attention due to the rapid use of fossil fuels inducing carbon dioxide emissions ever since the first industrial revolution in the 18th century. Polymer electrolyte membrane fuel cells (PEMFCs) that can produce water during the reaction without the emission of carbon dioxide are promising devices for automotive and residential applications. As a key component of PEMFCs, polymer electrolyte membranes (PEMs) need to have high proton conductivity and physicochemical stability during the operation. Currently, perfluorinated sulfonic acid-based PEMs (PFSA-PEMs) have been commercialized and utilized in PEMFC systems. Although the PFSA-PEMs are found to meet these criteria, there is an ongoing need to improve these further, to be useful in practical PEMFC operation. In addition, the well-known drawbacks of PFSA-PEMs including low glass transition temperature and high gas crossover need to be improved. Therefore, this review focused on recent trends in the development of high-performance PFSA-PEMs in three different ways. First, control of the side chain of PFSA copolymers can effectively improve the proton conductivity and thermal stability by increasing the ion exchange capacity and polymer crystallinity. Second, the development of composite-type PFSA-PEMs is an effective way to improve proton conductivity and physical stability by incorporating organic/inorganic additives. Finally, the incorporation of porous substrates is also a promising way to develop a thin pore-filling membrane showing low membrane resistance and outstanding durability.

• The Journal of the Convergence on Culture Technology
• /
• v.8 no.5
• /
• pp.71-80
• /
• 2022

The purpose of this study was to evaluate the effects of the non-pharmacological intervention on depressive symptoms in the older adults with mild cognitive impairment. A total of 1,147 studies were retrieved from PubMed, CINAHL, PsycINFO, Science direct, KISS, RISS, and DBPia. Twenty-one studies which met the criteria were selected and the quality assessment was conducted independently by two investigators. The effect size of non-pharmacological intervention was estimated using Comprehensive Meta-Analysis 3.0. The overall effect size turned out to be the medium effect size (Hedges' g=-0.68, 95% CI=-1.01~-0.36). As a result of the subgroup analysis, the intervention type was statistically significant. The effect size of cognitive intervention (Hedges' g=-1.03, 95% CI=-1.43~-0.61) and multi component intervention (Hedges' g=-0.97, 95% CI=-1.63~-0.33) was greater than excise intervention (Hedges' g=-0.53, 95% CI=-1.16~0.03). This study shows that non-pharmacological intervention was also effective in reducing depressive symptoms in the older adults with mild cognitive impairment. Based on the research results, it is expected that various non-pharmacological intervention studies will be attempted to improve cognitive function and depressive symptoms of the older adults with mild cognitive impairment.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.49 no.2
• /
• pp.127-139
• /
• 2023

In this study, minoxidil, which is well known as a pharmaceutical raw material, and diaminopyrimidine oxide (DAO), which is a cosmetic raw material, were used as active ingredients to evaluate the physical properties of niosomes and compare the skin penetrations of artificial skin. To prepare niosomes of the size of nanoparticles, a high pressure homogenization method was used, and physical properties were evaluated with a zetasizer. The particle size of the noisome including the active ingredient was measured to be 99 to 123 nm according to HLB, and the zeta potential was measured in the range of -60 to -81 mV. Through DSC (differential scanning colorimetry), it was confirmed that minoxidil, a crystalline component, was uniformly dissolved in an amorphous state in niosomes. In order to confirm and compare skin penetration, it was measured by the in vitro Franz diffusion cell method, and the niosome formulation showed 3.4 times higher penetration for minoxidil and 11.1 times higher penetration for DAO than the control gel formulation. In addition, when comparing the skin penetration of minoxidil niosome and DAO niosome, a similar trend was shown, and the penetration amount of DAO was relatively high. The shapes of the niosome formulations with different HLB values were observed using Cryo-TEM, and it was confirmed that vesicles were formed in all of them and that they were intermediate between SUV (small unilamella vesicle) and LUV (large unilamella vesicle). Through this study, minoxidil, an effective drug for hair loss, and DAO, a cosmetic raw material, can be effectively delivered to the skin by encapsulating them in a noisome formulation.

• Analytical Science and Technology
• /
• v.19 no.5
• /
• pp.441-448
• /
• 2006

11-nor-9-carboxy-${\Delta}^9$-tetrahydrocannabinol (THCCOOH) is the major metabolite of tetrahydrocannabinol (THC) which is the primary psychoactive component of marijuana. It is also the target analyte for the discrimination marijuana use. A method using solid-phase extraction (SPE) and gas chromatography/mass spectrometry (GC/MS) was developed for the determination of THCCOOH in human urine. Urine samples (3 mL) were extracted by SPE column with a cation exchange cartridge after basic hydrolysis. The eluents were then evaporated, derivatized, and injected into the GC/MS. The limits of detection (LOD) and quantitation (LOQ) were 0.4 and 1.2 ng/mL, respectively. The response was linear with a correlation coefficient of 0.999 within the concentration range of 1.2 (LLE 1.3)~50.0 ng/mL. The precision and accuracy were stable within 1.20% and the recovery was 83.6~90.7%. The recovery of SPE method was lower than that of liquid-liquid extraction (LLE), but there were no apparent differences in LOD, LOQ, precision and accuracy between the two methods. While SPE method is used as a very effective and rapid procedure for sample pretreatment, and clean extracts, LLE method was not suitable for the extraction procedure of THCCOOH in urine. The applicability of the method was proven by analyzing a urine samples from a marijuana abusers.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.2B
• /
• pp.177-185
• /
• 2008

Accurate monitoring of snow cover is a key component for studying climate and global as well as for daily weather forecasting and snowmelt runoff modelling. The few observed data related to snowmelt was the major cause of difficulty in extracting snowmelt factors such as snow cover area, snow depth and depletion curve. Remote sensing technology is very effective to observe a wide area. Although many researchers have used remote sensing for snow observation, there were a few discussions on the characteristics of spatial and temporal variation. Snow cover maps were derived from NOAA AVHRR images for the winter seasons from 1997 to 2006. Distributed snow depth was mapped by overlapping between snow cover maps and interpolated snowfall maps from 69 meteorological observation stations. Model parameters (Snow Cover Area: SCA, snow depth, Snow cover Depletion Curve: SDC) were built for 7 major watersheds in South Korea. The decrease pattern of SCA for time (day) was expressed as exponentially decay function, and the determination coefficient was ranged from 0.46 to 0.88. The SCA decreased 70% to 100% from the maximum SCA when 10 days passed.

• Journal of the Microelectronics and Packaging Society
• /
• v.30 no.3
• /
• pp.40-50
• /
• 2023

Recently, the number of components of smartphones increases rapidly, while the PCB size continuously decreases. Therefore, 3D technology with a stacked PCB has been developed to improve component density in smartphone. For the s tacked PCB, it i s very important to obtain solder bonding quality between PCBs. We investigated the effects of the properties, thickness, and number of layers of interposer PCB and sub PCB on warpage of PCB through experimental and numerical analysis to improve the reliability of the stacked PCB. The warpage of the interposer PCB decreased as the thermal expansion coefficient (CTE) of the prepreg decreased, and decreased as the glass transition temperature (Tg) increased. However, if temperature is 240℃ or higher, the reduction of warpage is not large. As FR-5 was applied, the warpage decreased more compared to FR-4, and the higher the number and thickness of the prepreg, the lower the warpage. For sub PCB, the CTE was more important for warpage than Tg of the prepreg, and increase in prepreg thickness was more effective in reducing the warpage. The shear tests indicated that the dummy pad design increased bonding strength. The tumble tests indicated that crack occurrence rate was greatly reduced with the dummy pad.

• Proceedings of the Plant Resources Society of Korea Conference
• /
• 2020.08a
• /
• pp.101-101
• /
• 2020

Soybean is known as to have a several healthy ingredients. Among them, isoflavones are effective in reducing obesity, menopausal symptom. Isoflavones consist of 12 isomers, including Aglycon, Glucoside, Malonyl glucoside, Acetyl glucoside, and are usually found in soybean seeds. The content is determined by the sum of 12 isomers, and the content value difference between the varieties is huge. In this study, we investigated the agronomic traits, 12 isomer of isoflavone content and composition for 49 soybean germplasms. This germplasms were selected from the 23,000 germplasms with the highest total content of isoflavones possessed by the National Agrobiodiversity Center. Seed samples were cultivated in experimental field located in Jeonju City on April 04, 2019. Matured seeds were harvested and portions of each seed samples were oven-dried, pulverized, and analyzed for their isoflavone compositions using HPLC-DAD. The soybean samples showed distinction in their agronomic traits, isoflavone compositions and contents. The days to flowering ranged between 38 and 69 days while the days to maturity ranged between 103 and 156 days. The seed coat color of soybean germplasms was 24 in black, 10 in yellow, 2 in green, 5 in yellowish green, 4 in green with black spot, 4 in pale yellow. The germplasm with the highest total content of isoflavones was the IT178054(1257.61±7.98 ㎍/g), but the germplasms containing the largest number of isoflavone isomers were IT274592, IT275005, both germplasms had 11 isoflavone isomers excluding Malonyl glycitin. The largest source of Aglycon, the most easily absorbed isoflavone form in the human body, was IT274592(DZ: 8.83±0.30 ㎍/g, GL: 11.14±0.81 ㎍/g, GE: 8.16±0.26 ㎍/g), while only IT274592, IT275005, IT308619 contained all three components of Aglycon. In Principal Component Analysis(PCA), the first two principal components showed more than 3.5 Eigen value and accounted for 58.2% of variability. The total content value had strong relationship with Malonyl genistin content value. Acetyl isomers had strong relationship, but Malonyl isomers were only related to isomers except Malonyl glycitin. These results will help in research on soybean varieties to enhance isoflavone ingredients.