• Structural Engineering and Mechanics
• /
• 제81권1호
• /
• pp.81-91
• /
• 2022

The effects of interaction between concrete-gypsum interface and edge crack on the failure behavior of the specimens in senicircular bend (SCB) test were studied in the laboratory and also simulated numerically using the discrete element method. Some quarter circular specimens of gypsum and concrete with 5 cm radii and hieghts were separately prepared. Then the semicircular testing specimens were made by attaching one gypsum and one concrete sample to one another using a special glue and one edge crack is produced (in the interface) by do not using the glue in that part of the interface. The tensile strengths of concrete and gypsum samples were separately measured as 2.2 MPa and 1.3 MPa, respectively. during all testing performances a constant loading rate of 0.005 mm/s were stablished. The proposed testing method showed that the mechanism of failure and fracture in the brittle materials were mostly governed by the dimensions and number of discontinuities. The fracture toughnesses of the SCB samples were related to the fracture patterns during the failure processes of these specimens. The tensile behaviour of edge notch was related to the number of induced tensile cracks which were increased by decreasing the joint length. The fracture toughness of samples was constant by increasing the joint length. The failure process and fracture pattern in the notched semi-circular bending specimens were similar for both methods used in this study (i.e., the laboratory tests and the simulation procedure using the particle flow code (PFC2D)).

• 한국공작기계학회논문집
• /
• 제14권1호
• /
• pp.30-36
• /
• 2005

This study is to investigate a damage estimation of single edge notched tensile specimens as a function of acoustic emission(AE) according to the uni-directionally oriented carbon fiber/epoxy composites, CFRP In fiber reinforced composite materials, AE signals due to several types of failure mechanisms are typically observed. These are due to fiber breakage, fiber pull-out matrix cracking, delamination, and splitting or fiber bundle breaking. And these are usually discriminated on the basis of amplitude distribution, event counts, and energy related parameters. In this case, AE signals were analyzed and classified 3 regions by AE event counts, energy and amplitude for corresponding applied load. Bath-tub curve shows 3 distinct periods during the lifetime of a single-edge-notch(SEN) specimen. The characterization of AE generated from CFRP during SEN tensile test is becoming an useful tool f3r the prediction of damage failure or/and failure mode analysis.

• 한국경영과학회지
• /
• 제26권3호
• /
• pp.65-77
• /
• 2001

Survivability of a network is one of the most important issues in designing present-day communication networks. the k-edge survivability of a given network is defined as the percentage of total traffic surviving the worst case failure of k edges. Although several researches calculated k-edge survivability on small networks by enumeration, prior research has considered how to calculate k-edge survivability on large networks. In this paper, we develop an efficient procedure to obtain lower and upper bounds on the k-edge survivability of a network.

• Geomechanics and Engineering
• /
• 제15권4호
• /
• pp.927-935
• /
• 2018

The mechanical behavior of the brittle material samples containing the internal and edge cracks are studied under direct shear tests. It is tried to investigate the effects of stress interactions and stress intensity factors at the tips of the pre-existing cracks on the failure mechanism of the bridge areas within these cracks. The direct shear tests are carried out on more than 30 various modeled samples each containing the internal cracks (S models) and edge cracks (E models). The visual inspection and a low power microscope are used to monitor the failure mechanisms of the tested samples. The cracks initiation, propagation and coalescences are being visualized in each test and the detected failure surfaces are used to study and measure the characteristics of each surface. These investigations show that as the ratio of the crack area to the total shear surface increases the shear failure mode changes to that of the tensile. When the bridge areas are fixed, the bridge areas in between the edge cracks have less strength than those of internal cracks. However, the results of this study show that for the case of internal cracks as the bridge area is increased, the strength of the material within the bridge area is decreased. It has been shown that the failure mechanism and fracture pattern of the samples depend on the bridge areas because as the bridge area decreases the interactions between the crack tip stress fields increases.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제17권2호
• /
• pp.450-470
• /
• 2023

Traditional cloud computing faces some challenges such as huge energy consumption, network delay and single point of failure. Edge computing is a typical distributed processing platform which includes multiple edge servers closer to the users, thus is more robust and can provide real-time computing services. Although outsourcing data to edge servers can bring great convenience, it also brings serious security threats. In order to provide image retrieval while ensuring users' data privacy, a privacy preserving image retrieval scheme in edge environment is proposed. Considering the distributed characteristics of edge computing environment and the requirement for lightweight computing, we present a privacy-preserving image retrieval scheme in edge computing environment, which two or more "honest but curious" servers retrieve the image quickly and accurately without divulging the image content. Compared with other traditional schemes, the scheme consumes less computing resources and has higher computing efficiency, which is more suitable for resource-constrained edge computing environment. Experimental results show the algorithm has high security, retrieval accuracy and efficiency.

• Geomechanics and Engineering
• /
• 제6권6호
• /
• pp.561-575
• /
• 2014

Estimating seismic displacements has a great importance for foundations on or adjacent to slope surfaces. However, dynamic solution of the problem has received little attention by previous researchers. This paper presents a new analytical model to determine seismic displacements of the shallow foundations adjacent to slopes. For this purpose, a dynamic equilibrium equation is written for the foundation with failure wedge. Stiffness and damping at the sliding surface are considered variable and a simple method is proposed for its estimation. Finally, for different failure surfaces, the calculated dynamic displacement and the surfaces with maximum strain are selected as the critical failure surface. Analysis results are presented as curves for different slope angles and different foundation distances from edge of the slope and are then compared with the experimental studies and software results. The comparison shows that the proposed model is capable of estimating seismic displacement of the shallow foundations adjacent to slopes. Also, the results demonstrate that, with increased slope angle and decreased foundation distances from the slope edge, seismic displacement increases in a non-linear trend. With increasing the slope angle and failure wedge angle, maximum strain of failure wedge increases. In addition, effect of slope on foundation settlement could be neglected for the foundation distances over 3B to 5B.

• Advances in materials Research
• /
• 제13권4호
• /
• pp.299-319
• /
• 2024

Due to higher strength-to-weight ratio of composite laminates, they find uses in many weight-sensitive applications like aerospace, automobile and marine structures. From a reliability point of view, accurate prediction of failure of these structures is important. Due to the complexities in the manufacturing processes of composite laminates, there is a variation in the material properties and geometric parameters. Hence stochastic aspects are important while designing the composite laminates. Many existing works of composite laminate failure analysis are based on the deterministic approach but it is important to consider the randomness in the material properties, geometry and loading to predict accurate failure loads. In this paper the statistics of the ultimate failure load of the [0/θ]_s laminated composite plate (LCP) containing the edge crack and voids subjected to the tensile loading are presented in terms of the mean and coefficient of variance (COV). The objective is to better the efficacy of laminate failure by predicting the statistics of the ultimate failure load of LCP with random material, geometric and loading parameters. The stochastic analysis is done by using the extended finite element method (XFEM) combined with the second-order perturbation technique (SOPT). The ultimate failure load of the LCP is obtained by ply-by-ply failure analysis using the ply discount method combined with the Tsai-Wu failure criterion. The aim is to know the effect of the stacking sequence, crack length, crack angle, location of voids and number of voids on the mean and corresponding COV of the ultimate failure load of LCP is investigated. The results of the ultimate failure load obtained by the present method are in good agreement with the existing experimental and numerical results. It is observed that [0/θ]_s LCPs are very sensitive to the randomness in the crack length, applied load, transverse tensile strength of the laminate and modulus of elasticity of the material, so precise control of these parameters is important. The novelty of the present study is, the stochastic implementation in XFEM for the failure prediction of LCPs containing crack and voids.

• Composites Research
• /
• 제25권2호
• /
• pp.40-45
• /
• 2012

복합재료가 기계부품, 항공기 구조물에 폭 넓게 적용됨에 따라, 복합재료 구조물에서 가장 취약한 복합재료 체결부의 설계는 매우 중요한 연구 분야로 대두되고 있다. 본 논문에서는 기계적 체결방법의 문제점으로 발생하는 원공주위의 높은 응력집중현상을 감소시키기 위하여, 복합재료 키 조인트(composite key joint)를 제안하였고 파손강도를 평가하였다. 제안된 복합재료키 조인트 체결부의 파손 판정을 위해서 파손지수(failure index)와 파손영역법(damage area theory)이 각각 적용되었다. 실험 결과로부터 복합재료 키 조인트는 기계적 체결부의 파손강도보다 93% 높은 값을 가짐을 볼 수 있었고, 복합재료 키 홈 깊이(key slot depth)가 0.88 mm이고 끝단 길이(edge length)가 20 mm일 때 가장 높은 파손하중 나타내었다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 가을 학술발표회 논문집
• /
• pp.173-178
• /
• 2002

Flat plate is susceptible to punching shear failure at the slab-column connection, which may cause catastrophic structural collapse. To prevent such brittle failure, strength and ductility of the connection should be ensured. However, since it is very difficult to experimentally simulate the actual load and boundary conditions of the flat plate system, it is not easy to obtain reliable information and data regarding to the strength and ductility of the flat plate-column edge connection. In the present study, numerical studies were performed for edge connections of continuous flat plate. The results were compared with the existing experiments, and the variations of bending moment, drift, effective width around the connection were investigated. Based on tile findings of the numerical studies, the disadvantages of current design methods were discussed.

• Structural Engineering and Mechanics
• /
• 제29권6호
• /
• pp.623-642
• /
• 2008

While spatial plastic mechanism analysis has been widely and successfully applied to thinwalled steel structures to analyse the post-failure behaviour of sections and connections, there remains some contention in the literature as to the basic capacity of an inclined yield line. The simple inclined hinge commonly forms as part of the more complex spatial mechanism, which may involve a number of hinges perpendicular or inclined to the direction of thrust. In this paper some of the existing theories are compared with single inclined yield lines that form in flange outstands, by comparing the theories with plate tests of plates simply supported on three sides with the remaining (longitudinal) edge free. The existing mechanism theories do not account for different in-plane displacement gradients of the loaded edge, nor the slenderness of the plates, and produce conservative results. A modified theory is presented whereby uniform and non-uniform in-plane displacements of the loaded edge of the flange, and the slenderness of the flange, are accounted for. The modified theory is shown to compare well with the plate test data, and its application to flanges that are components of sections in compression and/or bending is presented.