• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.64 no.4
• /
• pp.199-206
• /
• 2015

A rising attention is paid to the railway system in many countries. KOREA is also of the opinion that the railway has to play a more important role in the near future to face up to the problems that increase gradually in the transport sector. To attract more traffic to the rail networks, it is important for rail modes to have running time competitiveness. Tilting trains, where it is possible to tilt the car-body towards the center of the curve, are a less expensive alternative to shorten travelling times on existing lines. Running time for tilting train is one of the most important factors, with which passenger demand forecasting or economic feasibility analysis will be done. This paper evaluates the speed limitation of tilting train around curves and also presents calculation process of its simulated possible running time. Then the adequacy of estimated time is verified with running time for Korean protype tilting train TTX (Tilting Train eXpress) by actual test run. As a case study, the estimated running time for the production version of tilting train and its time saving are presented compared with 2012's conventional Saemaul trains and non-tilting trains on the Gyeongbu line in the Korean rail network.

• Journal of the Korean Institute of Navigation
• /
• v.16 no.2
• /
• pp.1-19
• /
• 1992

A Study for the relation between design parameters in conceptual stage and freight cost in operation of ocean-going bulk carrier was presented by economic criterial. Ship design procedure was followed to traditional method and programmed. The measure of merit is the Required Freight Rate(RFR). Parametric method used insteady of optimization technique due to easy to illustrate the results. Calculation results to the relation ship dimension, speed and operating cost in this paper show the influence of oil price is very important. Particularly, when oil price estimated as go up, owner choose a ship which lengh is long , breadth/draft is near 2.0 and speed is low. This program is useful for shipyard, consultant officer and owner all together.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.64 no.3
• /
• pp.169-174
• /
• 2015

Noise problem that occurs on the road is raising a lot of problems in the economic, social and environmental aspects. The active noise control (ANC) systems based on the filtered-X least mean square(FxLMS) algorithm have a problem with compensating the acoustic feedback of secondary route. However, newly proposed correlation-LMS(CLMS) and expanded CLMS algorithms have slightly much calculation and are minutely behind performance, these have a advantage not in measuring transfer function onerously so that we can easily adapt these in real time. The CLMS and expanded CLMS algorithm was developed to improve the real-time implementation performance under the variable input noise such as road noise environment. In this paper, we compared and analyzed their performance. From the results of the Matlab simulation for an ANC system, it is shown that expanded CLMS algorithms are more convergence speed and keep the desirable performance even in the input of road noise situation.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.4
• /
• pp.513-521
• /
• 2012

With the advent of smart grid, distribution network charges have been one of keystones of ongoing deregulation and privatization in power industries. This paper proposes a new charging methodology to allocate the existing distribution network cost with an aim of reflecting the true cost and benefit of network customers, especially of distribution generator (DG). The proposed charging methodology separates distribution network costs due to the respective real and reactive power flows. The costs are then allocated to network users according to each charge for the actual line capacity used and available capacity. This distribution network charging model is able to provide the economic signals to reward network users who are contributing to better power factors, while penalizing customers who worsen power factors. The proposed method is shown on IEEE 37 bus system for distribution network, and then the results are validated through the comparison with the MW-Miles and MVA-Miles methods. The charges derived from the proposed method can provide appropriate incentives/penalties to network customers to behave in a manner leading to a better network condition.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.22 no.3
• /
• pp.259-267
• /
• 2016

The study performs a risk analysis on container ship accidents using accident data collected over the six years from 2006 to 2011, presents the resulting risk level, and suggests three risk mitigation measures to reduce the overall risk, for the safer operation of container ships. More specifically, starting from the initial accident of collision, we developed 13 different accident scenarios using event tree analysis based on which the overall risk level was obtained and presented as a FN curve. Since diverse human factors are the main cause of most of the ship accidents, our study focuses on the effect of reducing human causes on the resulting risk level. For the research we considered the injuries for the calculation of fatality with the help of MAIS. The results show that collision was the main type of accident, accounting for 62 % of all accidents, and the measures employed were proven to be effective in the sense that the risk level was much lowered and the average number of fatalities was also reduced. With more data accumulated, more precise risk level will be calculated with which the practical risk mitigating measures will be also developed. For future study, economic loss and environmental damage as consequences need to be considered.

• Computers and Concrete
• /
• v.9 no.2
• /
• pp.119-131
• /
• 2012

Optimum packing of aggregate is an important aspect of mixture design, since porosity may be reduced and strength improved. It may also cause a reduction in paste content and is thus of economic relevance too. Several mathematic packing models have been developed in the literature for optimization of mixture design. However in this study, numerical simulation will be used as the main tool for this purpose. A basic, simple theoretical model is used for approximate assessment of mixture optimization. Calculation and simulation will start from a bimodal mixture that is based on the mono-sized packing experiences. Tri-modal and multi-sized particle packing will then be discussed to find the optimum mixture. This study will demonstrate that computer simulation is a good alternative for mixture design and optimization when appropriate particle shapes are selected. Although primarily focusing on aggregate, optimization of blends of Portland cement and mineral admixtures could basically be approached in a similar way.

• Asian-Australasian Journal of Animal Sciences
• /
• v.12 no.8
• /
• pp.1316-1323
• /
• 1999

Extensive emphasis on milk and milk fat yields with no diversion for beef performance increased the yield efficiency of North American dairy cattle. Heavy demand for North American genetics followed national strain comparison trials in Poland, and US and Canadian dairy cattle and germplasm still are an important source of genetics for many countries. Genetic improvement has accelerated in many countries because of the implementation of sampling programs for young bulls and improved evaluation procedures. Rapid access to information and more frequent calculation of genetic information also are having a positive impact on genetic improvement. Traits other than yield should be considered in a breeding program, but those traits mist have a reasonable opportunity for improvement and sufficient economic worth. Because of ever increasing efficiency, the world's milk supply comes from fewer cows each year. However, no decline in the rate of genetic improvement is apparent under current genetic practices; estimates of heritability are increasing, and a decline in yield efficiency is unlikely in the near future. As management improves, especially for subtropical conditions, many of the selection principles used in temperate climates will be adopted for more adverse environmental conditions.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.10 no.3
• /
• pp.45-52
• /
• 2010

The relationship between climate changes and transportation could be separated by two approaches. One of methods was to find how climate changes affected transportation, and the other way was how transportation affected climate changes. In this study, we reported from the former standpoint, how climate changes affected transportation fields. When there is a lot of snowfall in Seoul, it starts ripple effect through the travel patterns. They can be explained by travel time and operating cost. The travel costs were calculated in this paper for analysing the effect of disbenefit by climate changes. Snow Melting System was also studied for relieving negative influences under the unpredictable weather condition. As a result, the system was effective for minimizing disbenefit by climate changes.

• Proceedings of the Korean Institute Of Construction Engineering and Management
• /
• 2004.11a
• /
• pp.394-397
• /
• 2004

Working-day calculation with weather factors of construction-site has estimated wethout proper data. They usually estimate it with their own experience and intuition. It causes not only economic loss to time-adjustment but also conflict with each participants. Moreover, weather estimation becomes worse than before, due to tendency of recently weather change. So, in this paper we present optimal estimation method as assessment by period of the arithmetical mean methods. For that, we analyse characteristic of the regions and weather change of temperature and rainfall which affects time.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2002.09a
• /
• pp.223-230
• /
• 2002

Earthquake resistance design has been developed many countries like Japan, USA, Mexico, New Zealand etc., which countries have experienced many earthquakes. Nowadays, earthquake resistance design has come into worldwide use. In Korea, the seismic design regulations have been established since 1988 in order to minimize the economic losses. Recently performance based design method has been adopted as a new Earthquake resistance design method. These regulations, however, are targeted for newly constructed buildings, In Korea, there are no regulations for existing buildings that built before 1988. On the other hand, in Japan and USA, the seismic performance evaluation is coded. In Japan, the evaluation index which can measure seismic performance has been made. So, we need to prepare the regulations that evaluate the seismic performance, furthermore proper retrofitting design guideline needs to be proposed when remodeling old buildings. In this research, various seismic performance evaluation methods which are being used in Japan and USA are reviewed in order to establish seismic performance evaluation index for those existing old structures in Korea.