• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.9
• /
• pp.4177-4185
• /
• 2012

LEDs are becoming the most suitable candidate replacing traditional fluorescent lamps because of its eco-friendly characteristics. LEDs are also actively used to design green building system and to make outdoor billboard as a back-light system due to its high energy efficiency. In this paper, we have developed AC direct driver for $12{\times}12$ FLB(flexible LED board) and LED flat light without SMPS. It has LID-PC-R101B driver IC that can support the high power factor and be composed of LED switching circuit in group. Also, an elaborate system designs can guarantee a high luminous efficiency, a high reliability and a low power consumption. The proposed FLB has the ultra slim shape of $450{\times}450$ mm, width of 4 mm and weight of 280 g. In the end, we have developed a prototype of FLB for billboard and flat light for room lighting with AC direct driver iposrder to verify the performance of the proposed system.

• Journal of Conservation Science
• /
• v.32 no.3
• /
• pp.377-384
• /
• 2016

There are physical and chemical method for removement of a lacquered layer existing on the surface when gilding an iron Buddha, these caused environmental pollution by surface degradation and is very noxious for conservation scientist's health. Thus, on this study, we conducted a lacquered layer removement experiments using Nd:YAG Laser which is contactless and eco-friendly. Specimens were made by polishing $5{\times}5$ size of iron(99.9%) specimens surfaces evenly and by differing of number of coating of unrefined lacquer, so there were thickness differences of $10{\mu}m$, $20{\mu}m$, and $30{\mu}m$. The laser machine used in this study was Nd:YAG Laser, and we used two wavelength modes; 1064 nm(160~180 mJ) for infrared light region and 532 nm(50~350 mJ) for ultraviolet light region. The experiment done by investigating the transition of specimens' surfaces with laser wavelength, energy, and numbers of investigation. The remain amount of lacquered layer surfaces before/after laser irradiation was investigated by stereoscopic microscope, observation by SEM, Non-contact Surface Roughness Measurement Device, and FT-IR etc. As a result of each analysis, we could verify the thickness of $10{\mu}m$, $20{\mu}m$ of lacquered layer removed without surface degradation when using 1064 nm wavelength with $1.0J/cm^2$ density. We could find out that Nd:YAG Laser is effective for removing remained lacquered layers when gilding an iron Buddha. In the future, when not only the metal has made various studies also wood lacquered furniture or the like, it seems to be utilized to remove the lacquer without surface damage.

• Journal of Environmental Impact Assessment
• /
• v.26 no.1
• /
• pp.78-92
• /
• 2017

Environmental impact assessment(EIA) on the construction and operation of thermal power plant(TPP) is aimed at promoting sustainable coastal development by clearly identifying the marine physics and organisms effects of the project on the surrounding marine environment and minimizing its impact. The primary purpose of this study is to establish EIA guidelines for TPP in order to assess how TPP construction projects influence marine environment and to establish the mitigaion plans of environmental impacts. Through this study, scientific and efficient EIA guidelines for the marine environments were established by a specialist forum consisted of officials from the Ministry of Environment and the Ministry of Trade, Industry and Energy, personnel from five public corporations in charge of TPPs and marine environment experts. In the study, fifteen EIA reports (2009~2015) on TPPs submitted were analyzed to identify the shortcomings of current assessment items on marine environment and to collect a wide range of information including EIA report formulation regulations, domestic and overseas environmental survey guidelines and EIA review comments on TPPs. Based on the findings, a specialist forum put together EIA guidelines for TPP construction projects.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.10
• /
• pp.590-597
• /
• 2018

Recently, the installation of PV systems has been increasing due to the worldwide interest in eco-friendly and renewable solar energy. On the other hand, the output power of PV systems is influenced strongly by the surrounding weather conditions. In addition, the entire operation efficiency of PV systems may be decreased considerably even if only some of the PV modules are in the shade. In other words, the existing control method at which strings with modules in series are connected to an inverter may be not operated in the case that the string voltage in partial shade is lower than the operating range of the grid connected inverter. To overcome these problems, this paper proposes an operation efficiency improvement device of a PV system using a Li-ion battery, which can compensate for the voltage of each string in the PV system when it is partially shaded. In addition, this paper presents the modeling of the operation efficiency improvement device, including PV strings, Li-ion battery and a 3-Phase grid inverter based on the PSIM S/W. From the simulation results, it was confirmed that the proposed control method can improve the operating efficiency of PV systems by compensating for the string voltage with partial shade.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.24 no.4
• /
• pp.11-20
• /
• 2016

Depletion of natural resources and reduction of greenhouse gas emissions are an important issue which we have to solve. The recycling of waste has emerged as a global concern. In Korea, the development of cost-effective treatment and recycling technologies also need to be improved. In this study, we compared and analyzed the cost per unit of treatment and recycling of organic waste, and presented an effective recycling scheme. We investigated the current status of treatment and costs for six types of organic wastes from 80 workplaces, including organic wastewater treatment sludge, processed organic sludge, and plant residues. In addition, environmental costs for greenhouse gas reduction were calculated. It's an economic way that organic waste is composted and used as cement additives. In particular, the economic analysis was done by realistic results of the survey target companies. In conclusion, in order for reliable processing and recycling of organic wastes, wastewater treatment sludge and sewage sludge need to be classified based on hazard characteristics. Finally, technical difficulties need to be further resolved such as odors, leachate, and debris on recycling organic wastes.

• Journal of Korean Society of Environmental Engineers
• /
• v.38 no.7
• /
• pp.387-394
• /
• 2016

Commercial 28 algae removal technologies that have been applied in domestic rivers and lakes with green tide were investigated, analyzed and classified. The classification of algae removal technologies was based on the three criteria (i.e., principle, flow rate of water body, and application period). Also, algae removal technologies were evaluated in terms of cost effectiveness, field applicability, effect durability, and eco friendliness. From the analysis results, technologies using physical, chemical, biological, and convergent controls were 32.2%, 25%, 21.4%, and 21.4%, respectively. The 75% of technologies have been applied to stagnant water body (${\leq}0.2m/s$). Also, algae harvesting ship with dissolved air flotation, conveyor belt and filtration processes and natural floating coagulant were found to have better field applicability, compared to other technologies. However, proper algae removal technology in specific rivers and lakes should be chosen after the evaluation of long-term pilot scale field test. Also, development of energy and resource recovery technologies from algae biomass is warranted.

• The Journal of the Korea Contents Association
• /
• v.18 no.9
• /
• pp.675-683
• /
• 2018

As interest in eco-friendly architecture and Korean traditional culture is increasing, interest in contemporary han-ok is steadily increasing. Recently, many people experienced the han-ok directly and indirectly with the attention of a commercial contemporary han-ok such as restaurants, coffee shops, and lodging facilities, and as a result, the house has a preference for the residence of the contemporary han-ok. Compared to modern residential houses, however, han-ok is lack the convenience of heating and cooling, energy management, security, and maintenance. For this reason, the increased interest and preference for han-ok does not lead to living in contemporary han-ok. This study was conducted in the following ways to improve inconvenience by applying smart home services to contemporary han-ok. Recent technology trends in smart home services and technologies developed and marketed to date have been identified in previous research cases and literature studies. Based on this, a list of smart home services and their application methods were derived that would relieve the inconvenience of contemporary han-ok for smart home services. We hope that this research will serve as a reference for subsequent researchers studying contemporary han-ok.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.2
• /
• pp.660-667
• /
• 2018

This study examined the optimal manufacturing conditions of RDF using heat-dried sludge from sewage treatment plant in Cheonan with the oil-drying method. The amounts of oil evaporation and oil drying of the heat-dried sludge were measured at different temperatures to evaluate the value of the product. The performance of the product was then measured using a calorimeter and TGA. In addition, the concentration of odor, NH3, H2S, and TVOC during drying was determined using a portable odor-meter. Ingredient analysis was performed by EDS. Considering mass-production, the oil to heat-dried sludge weight ratio was fixed to 4:1. At $130^{\circ}C$, only physical mixing occurred after the instantaneous drying of internal water. Considering the eco-friendly aspects, there was no significant difference in the drying efficiency between $160^{\circ}C$ and $190^{\circ}C$. Therefore, the optimal conditions were a drying temperature of $160^{\circ}C$ within 5 minutes. Finally, the RDF manufactured in this study and fuel used in the thermal power plants were compared. The calorific value was 4,449kcal/kg, the water content was 2% and the ash content was 34%, which is higher than the fuel of thermal power plants. Therefore, it is believed that coal energy as well as wood pellets can be replaced.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.2
• /
• pp.294-301
• /
• 2017

In this study, we found the optimal manufacturing conditions of livestock manure sludge RDF with the oil-drying method. We performed oil evaporation, oil drying and pelletizing of the sludge to evaluate the value of the product (sludge RDF), and measured the performance of the product using calorimeter and PXRF equipment. Also, we conducted the calorie comparison test between sludge RDF manufactured in this study and wood RDF generally used in the field. Experimental results showed that 30g of the sludge treated by vegetable oil at $130^{\circ}C$ for 25 minutes were the optimal conditions to make the sludge RDF (considering the aspects of eco-friendly and mass production). The caloric value of the sludge RDF manufactured in this study was 5211kcal/kg which is higher than that of wood RDF used widely in the market. Finally, PXRF results showed sludge RDF contains no heavy metals with the exception of sulfur. Therefore, we recommend more study about the sulfur control process for future development of the industrial manufacturing process.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.7
• /
• pp.704-712
• /
• 2016

Recently, the installation of photovoltaic (PV) systems has been increasing due to the worldwide interest in eco-friendly and infinitely abundant solar energy. However, the output power of PV systems is highly influenced by the surrounding environment. For instance, a string of PV systems composed of modules in series may become inoperable under cloudy conditions or when in the shade of a building. In other words, under these conditions, the existing control method of PV systems does not allow the string to be operated in the normal way, because its output voltage is lower than the operating range of the grid connected inverter. In order to overcome this problem, we propose a new control method using a DC-DC voltage regulator which can compensate for the voltage of each string in the PV system. Also, based on the PSIM S/W, we model the DC-DC voltage regulator with constant voltage control & MPPT (Maximum Power Point Tracking) control functions and 3-Phase grid connected inverter with PLL (Phase-Locked Loop) control function. From the simulation results, it is confirmed that the present control method can improve the operating efficiency of PV systems by compensating for the fluctuation of the voltage of the strings caused by the surrounding conditions.