• Journal of Sensor Science and Technology
• /
• v.4 no.2
• /
• pp.58-63
• /
• 1995

The effects of substrate temperature, RF power, and $NH_{3}/SiH_{4}$ gas flow ratio on the dielectric constant and optical bandgap of amorphous silicon nitride (a-SiNx:H) thin films prepared by PECVD method using RF glow discharge decomposition of $SiH_{4}$ and $NH_{3}$ gas mixtures have been studied. The dielectric constant and optical bandgap of a-SiNx:H thin films were greatly exchanged as by increasing substrate temperature, RF power, and $NH_{3}/SiH_{4}$ gas flow ratio. The dielectric constant of a-SiNx:H films was increased and optical bandgap of a-SiNx:H films was decreased as the substrate temperature was increased. When the substrate temperature, RF power, gas pressure, $NH_{3}/SiH_{4}$ gas flow ratio, and thickness were $250^{\circ}C$, 20 W, 500 mTorr, 10 and $1500\;{\AA}$, respectively, the dielectric constant, breakdown field and optical bandgap of a-SiNx:H film were 4.3, 1 MV/cm, and 2.9 eV, respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.11
• /
• pp.977-982
• /
• 2005

Al/AlN/n-type 6H-SiC (0001) MIS structures were prepared by AlN layers on vicinal 6H-SiC(0001) substrates with reactive RF magnetron sputtering method. The AlN films were annealed at $900^{\circ}C$, $N_2$ atmosphere lot 1 minutes showed the best result. With XRD analysis, AlN(0002) peak was clearly found. The typical dielectric constant value of the AlN film in the MIS capacitors was obtained as 8.4 from photo C-V. Also, the gate leakage current density of the MlS capacitor was $10^{-10}\;A/cm^2$ order within the electric field of 1.8 MV/cm. Finally, the amount of interface trap densities, $D_{it}$, was evaluated as $5.3\times10^{10}\;eV^{-1}cm^{-2}$ at (Ec-0.85) eV.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.3
• /
• pp.51-57
• /
• 2010

A dual-mode direct conversion receiver is developed in $0.13\;{\mu}m$ RF CMOS process for IEEE 802.11n based wireless LAN and IEEE 802.16e based mobile WiMAX application. The RF receiver covers the frequency band between 2.3 and 2.7 GHz. Three-step gain control is realized in LNA by using current steering technique. Current bleeding technique is applied to the down-conversion mixer in order to lower the flicker noise. A frequency divide-by-2 circuit is included in the receiver for LO I/Q differential signal generation. The receiver consumes 56 mA at 1.4 V supply voltage including all LO buffers. Measured results show a power gain of 32 dB, a noise figure of 4.8 dB, a output $P_{1dB}$ of +6 dBm over the entire band.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.365-365
• /
• 2013

본 실험에서는 RF magnetron sputter장비와 evaporator장비를 이용하여 다층박막 IGZO/Ag/IGZO를 제작하였다. 소결된 타겟은 In:Ga:ZnO 1:1:1mol%로 조성된 타겟을 사용하였으며, Ag는 99.999%의 순도를 가진다.다층박막 OMO구조의 Oxide layer는sputter장비를 이용 IGZO막을 제작하였으며, Metal layer는 evaporator 장비를 이용 Ag막을 제작하였다. 변수로는 Metal layer 두께에 따른 구조적, 광학적 특성 변화를 연구하였다. Oxide layer의 RF sputter 공정 조건으로는 초기압력 $3.0{\times}10^{-6}$ Torr 이하로 하였으며, 증착압력 $2.0{\times}10^{-2}$ Torr, RF power 30 W, Ar 50 sccm으로 고정시켰으며, Metal layer의 evaporator 공정조건으로는 $5.0{\times}10^{-6}$ 이하, 전압은 0.3V, 기판 회전속도는 2RPM 두께는 Thickness moniter로 3. 5. 7. 9. 11. 13. 15 nm를 확인하며 증착하였다. 분석결과로는 AFM측정결과 거칠기는 2 nm이하의 거칠기를 확인했으며, XRD측정결과 Bragg's 법칙($2\;dsin{\Theta}=n{\lambda}$)를 만족하는 피크를 찾을 수 없어 비정질 구조임을 확인할 수 있었다. 투과도 측정결과 가시광 영역에서 최대 80% 이상의 투과율을 보여주었으며, IR영역에서는 30% 이하의 투과율을 보여주었다. 에너지 밴드갬 계산결과 4.5~4.6 eV를 갖는 것을 확인하였으며, Low-e 분야에 사용가능함을 보여주었다.

• Transactions on Electrical and Electronic Materials
• /
• v.14 no.2
• /
• pp.86-89
• /
• 2013

Dye-sensitized solar cells have a FTO/$TiO_2$/Dye/Electrode/Pt counter electrode structure, yet more than a 10% electron loss occurs at each interface. A passivating layer between the $TiO_2$/FTO glass interface can prevent this loss of electrons. In theory, ZnO has excellent electron collecting capabilities and a 3.4 eV band gap, which suppresses electron mobility. FTO glass was coated with ZnO thin films by RF-magnetron sputtering; each film was deposited under different $O_2$:Ar ratios and RF-gun power. The optical transmittance of the ZnO thin film depends on the thickness and morphology of ZnO. The conversion efficiency was measured with the maximum value of 5.22% at an Ar:$O_2$ ratio of 1:1 and RF-gun power of 80 W, due to effective prevention of the electron recombination into electrolytes.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.10a
• /
• pp.402-403
• /
• 2011

This paper has proposed a $0.13-{\mu}m$ CMOS RF Front-end transmitter for LTE-Advanced systems. The proposed RF Front-end supports a band 7 (from 2500 MHz to 2570 MHz) in E-UTRA of 3GPP. It can provide a maximum output power level of +10 dBm but it's a normal output power level is +0 dBm considering a low PAPR. The post-layout simulation results show that the quadrature up-conversion mixer and a driver amplifier consumes 14 mA and 28 mA from a 1.2 V supply voltage respectively, while providing a output power level of 0 dBm at the input power level of -13 dBm.

• Journal of Satellite, Information and Communications
• /
• v.4 no.1
• /
• pp.36-44
• /
• 2009

The key technologies of GNSS receiver for GNSS sensor station are under development as a part of a GNSS ground station in ETRI. This paper presents the GNSS receiver implementation and signal processing result which is implemented based on FPGA to process the Galileo E1 and E5 signal. To verify the working and performance for GNSS receiver which is implemented based on FPGA, live signal received from GIOVE-B which is second test satellite is used. We gather GIOVE-B signal by using prototyping antenna and RF/IF units including IF-component. To verify Galileo E1 and E5 signal processing function from GIOVE-B, FPGA based signal processing module is implemented as a prototyping hardware board.

• Electrical & Electronic Materials
• /
• v.10 no.7
• /
• pp.706-712
• /
• 1997

AlN(Aluminium Nitride) thin films were prepared using by RF sputtering method on the Si(100) and Si(111) substrates as the parameters of the substrate temperature, RF power, sputtering duration and the $N_2$/Ar ratio and investigated by X-ray diffraction, IR spectrometry, n&k analyzer. For the Si(100) substrate, the AlN thin films of (101) orientation were obtained under the conditions of room temperature and the nitrogen of 60 vol.%. For the Si(111) substrate, the (002) AlN thin films were obtained under the nitrogen of 100 vol.%. In case of the thin film prepared in the condition of above 60 vol.% of the nitrogen, the average value of the surface roughness of the film was 151$\AA$. From the changes of the half widths of E$_1$[TO] phonon bands at the wavenumber of 680$cm^{-1}$ /, it were compared of the crystallinities of the films which were grown under the different conditions. The thicknesses of AlN films were decreased dramatically in the region of the nitrogen of 40~60 vol.%. Its due to the nitridation of the Al target surface and getting low of the sputtering yield by the $N_2$/Ar ratio being increased.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2000.01a
• /
• pp.169-170
• /
• 2000

The conventional AC PDP has a relatively low efficiency which is close to 1.5 lm/W. If the AC sustain period is replaced by the RF sustain period, due to oscillating and low electric field, almost 60% of the supplied energy is spent by Xe excitation [1]. The efficiency of RF PDP can be $4{\sim}5$ times higher than that of AC PDP. In this paper, we will present the RF PDP that is a new type of PDP. A new display method in PDP using RF pulses is suggested and applied on a 4-inch-diagonal Panel (hereinafter 4" panel). Even though there were many researches in RF discharge, there was not enough research for display application. Now we propose the RF PDP that is a new display field and we will expect to do more research in this field.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.351-351
• /
• 2013

한국 전체 에너지 사용량 중약 24%의 에너지가 건축물 부분에 소비되고 있다. 건축물의 벽체나 유리창 등을 통해서 에너지 손실이 이루어지는데 유리창은 벽체에 비해 약 10배 이상 낮은 단열 특성을 가지고 있기 때문에 유리창을 통한 열손실량은 더 크다. 이러한 유리창 부분의 열손실 문제를 해결할 수 있는 방안으로 좋은 단열 특성 및 낮은 방사율을 가지고 있는 Low-e coating 방법을 사용하였다. 본 실험에서는 XG glass 기판 위에 IGZO/Ag/IGZO OMO 구조의 다층 박막을 증착하였다. RF magnetron sputtering방법을 이용하여 OMO 구조의 상부와 하부의 Oxide layer로 IGZO 박막을 증착하였다. 사용된 IGZO 타겟은 $In_2O_3$ (99.99%), $Ga_2O_3$ (99.99%), ZnO (99.99%)의 분말을 각각 1:1:1 mol% 조성비로 혼합하여 소결하여 제작하였다. Thermal Evaporator 장비를 이용하여 OMO 구조의 Metal layer로 Ag (99.999%)를 증착하였다. 실험 기판은 크기 $30{\times}30mm$의 0.7T XG glass를 사용하였다. OMO 구조의 산화층 IGZO 박막은 상/하층 동일 조건으로 기판 온도는 실온으로 고정하였으며, 초기 압력 $3.0{\times}10^{-6}$ Torr, 증착 압력 $3.0{\times}10^{-2}$ Torr, RF 파워 50W, Ar 유량 50 sccm로 고정시키고 증착 시간이 변화하면서 박막을 증착하였다. OMO 구조의 Metal layer로 Ag 증착 조건은 초기 진공도가 약 $6.0{\times}10^{-6}$ Torr 이하로 유지하고 기판을 2 Rpm의 속도로 회전시켰다. 이후 0.3 V로 Ag를 10분간 가열하여 충분히 녹인 후 Film Thickness Monitor로 두께를 확인하였다. OMO 다층 박막의 산화물층 변화에 따라 로이다층 박막의 구조적, 광학적 및 전기적 특성을 분석하였다. XRD 분석결과에 의하여 Bragg's 법칙을 만족하는 피크가 나타나지 않는 비정질 구조임을 확인할 수 있으며, AFM 분석결과에 통해서 최소 1.3 nm의 Roughness를 나타내었다. UV-Visible-NIR 분광광도계를 이용하여 다층 박막은 가시광선 영역에서 평균 80%의 광 투과성을 보여 IR 영역에서 평균 30% 투과하고 좋은 차단 특성을 나왔다. Low-e 특성을 갖는 유리창을 통해서 에너지 절약을 이룰 수 있는 것을 확인할 수 있었다.