• Composites Research
• /
• 제17권3호
• /
• pp.45-50
• /
• 2004

계면상 조건과 섬유 함유량 변화에 따른 단섬유 강화 CR의 동적특성에 대해 주파수, 진폭 그리고 온도를 함수로 실험적 고찰을 하였다. 진폭 변형률 증가에 따라 LF는 1.33% 이상에서 약간 증가하였고, DR은 크게 감소하였다. 주파수 증가에 따라 LF는 특히 50Hz 이후 크게 감소하였고, DR은 기지고무보다 낮은 값을 보였다. 온도 증가에 따라 LF는 $65^{\circ}$에서 최대 값을 나타내고 이후 크게 감소세를 보였다. DR은 온도가 증가에 따라 기지고무 보다 낮은 값을 보였다. 일반적으로 동일한 시험 조건에서 계면상이 우수할수록 LF와 DR이 낮은 값을 보였다. 따라서 단섬유 강화고무는 진동 수비가 $\sqrt{2}$ 이하보다는 $\sqrt{2}$ 이상에서 더 큰 진동절연 효과가 있다고 할 수 있다.

• Steel and Composite Structures
• /
• 제30권1호
• /
• pp.31-46
• /
• 2019

In the present study, the various dynamic properties of MWCNT embedded fiber reinforced polymer uniform and tapered composite (MWCNT-FRP) plates are investigated. Various configurations of a tapered composite plate with ply-drop off and uniform composite plate have been considered for the development of the finite element formulation and experimental investigations. First order shear deformation theory (FSDT) has been used to derive the kinetic and potential energy equations of the hybrid composite plates by including the effect of rotary inertia, shear deformation and non-uniformity in thickness of the plate. The governing equations of motion of FRP composite plates without and with MWCNT reinforcement are derived by considering a nine- node rectangular element with five degrees of freedom (DOF) at each node. The effectiveness of the developed finite element formulation has been demonstrated by comparing the natural frequencies and damping ratio of FRP composite plates without and with MWCNT reinforcement obtained experimentally. Various parametric studies are also performed to study the effect of CNT volume fraction and CNT aspect ratio of the composite plate on the natural frequencies of different configurations of CNT reinforced hybrid composite plates. Further the forced vibration analysis is performed to compare the dynamic response of the various configurations of MWCNT-GFRP composite plate with GFRP composite plate under harmonic excitations. It was observed that the fundamental natural frequency and damping ratio of the GFRP composite plate increase approximately 8% and 37% respectively with 0.5wt% reinforcement of MWCNT under CFCF boundary condition. The natural frequencies of MWCNT-GFRP hybrid composite plates tend to decrease with the increase of MWCNT volume fraction beyond 2% due to agglomeration of CNT's. It is also observed that the aspect ratio of the CNT has negligible effect on the improvement of dynamics properties due to randomly orientation of CNT's.

• 한국재난정보학회 논문집
• /
• 제20권2호
• /
• pp.369-378
• /
• 2024

연구목적: 본 연구는 복합 긴장 방식이 적용된 세그멘탈 PSC U형 거더와 콘크리트 바닥판 슬래브가 합성된 40m 실대형 실험체를 제작하여 동적 거동 실험을 실시하고 수치해석적기법 결과와 비교 검토함으로써 구조적 안정성을 검증하고자 한다. 연구방법: 손상이 없는 실대형 실험체에 impact hammer 타격으로 동적 거동 실험을 실시하여 고유진동수와 감쇠비를 측정하고 수치해석적기법 및 구조물의 일반적인 감쇠비와 상호 비교 검토하였다. 연구결과: 거더와 슬래브 합성단면으로 구성된 수치해석 모델의 고유진동수는 2.561Hz로 계산되었고 실대형 실험체의 고유진동수는 2.670Hz로 계측되었으며 감쇠비는 0.42~0.68%로 산정되었다. 결론: 실대형 실험체 고유진동수는 수치해석 모델의 고유진동수 대비 약 4.3% 증가된 값으로써 실대형 실험체와 수치해석 모델의 질량이 동일하므로(99.97%) 실대형 실험체 강성은 구조적 안전성을 확보하였음을 도출할 수 있으며 결과적으로 실험체의 동적 거동 안정성을 검증하였다. 계측된 감쇠비 0.42~0.68%는 탄성영역의 PSC구조물 감쇠비 0.5~1.0%와 비교하여 볼 때, 안정적 동적 거동임을 확인하였다.

• Structural Engineering and Mechanics
• /
• 제73권2호
• /
• pp.181-190
• /
• 2020

In this paper, non-linear dynamic buckling behaviour of laminated composite curved panels subjected to dynamic in-plane axial compressive loads is studied using finite element methods. The work is carried out using the finite element software ABAQUS. The curved panels are modelled with S4R element and the nonlinear dynamic equilibrium equations are solved using the ABAQUS/Explicit algorithm. The effect of aspect ratio, radius of curvature and thickness are studied. The importance of orientation of plies in the direction of loading is also reiterated in this study. Vol'mir's criterion is used to calculate the dynamic buckling loads. The panels are subjected to rectangular pulse load of various amplitude and durations and the responses are observed. For particular loading amplitude, a critical value of loading duration is observed beyond which the variation of dynamic buckling load is insignificant. It is also observed that, the value of dynamic bucking load reduces as the loading duration is increased though the reduction is not much after a particular loading duration.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 가을 학술발표회 논문집(I)
• /
• pp.111-116
• /
• 1998

Most previous wave tests for concrete have been done to evaluate static material properties, and thus there are less works to investigate dynamic material characteristics of concrete, which should be few in Korea. The objective of this experimental work is to investigate dynamic material characteristics of concrete, such as dynamic elastic modulus, dynamic shear modulus, first resonant frequency, dynamic poisson's ratio and etc. A dynamic Signal Analyzer has been used to perform the wave analysis for various dynamic material properties of test specimen. First Fourier transform technique has been carried out on various wave data acquired by the Resonant Column method, which is a kind of nondestructive tests. Wave analysis has been performed based on KS F2437, which is similar to ASTM C607-71 and is identical to JIS A 1127-1976.

• Structural Engineering and Mechanics
• /
• 제83권3호
• /
• pp.377-386
• /
• 2022

This paper considers dynamic impedance functions and presents a detailed analysis of the soil plasticity influence on the pile-group foundation dynamic response. A three-dimensional finite element model is proposed, and a calculation method considering the time domain is detailed for the nonlinear dynamic impedance functions. The soil mass is modeled as continuum elastoplastic solid using the Mohr-Coulomb shear failure criterion. The piles are modeled as continuum solids and the slab as a structural plate-type element. Quiet boundaries are implemented to avoid wave reflection on the boundaries. The model and method of analysis are validated by comparison with those published on literature. Numerical results are presented in terms of horizontal and vertical nonlinear dynamic impedances as a function of the shear soil parameters (cohesion and internal friction angle), pile spacing ratio and frequencies of the dynamic signal.

• 한국연소학회지
• /
• 제11권4호
• /
• pp.27-35
• /
• 2006

The impacts of equivalence ratio on flow structure and flame dynamic in a model gas turbine combustor are investigated using large eddy simulation(LES). Dynamic k-equation model and G-equation flamelet model are employed as LES subgrid model for flow and combustion, respectively. As a result of mean flow field for each equivalence ratio, the increase of equivalence ratio brings about the decrease of swirl intensity through the modification of thermal effect and viscosity, although the same swirl intensity is imposed at inlet. The changes of vortical structure and turbulent intensity etc. near flame surface are occurred consequently. That is, the decrease of equivalence ratio can leads to the increase of heat release fluctuation by the more increased turbulent intensity and fluctuation of recirculation flow. In addition, the effect of inner vortex generated from vortex breakdown on the heat release fluctuation is increased gradually with the decrease of equivalence ratio. Finally, it can be identified that the variations of vortical structure play an important role in combustion instability, even though the small change of equivalence ratio is occurred.

• 한국철도학회논문집
• /
• 제15권2호
• /
• pp.154-161
• /
• 2012

철도교량 동적 설계 및 동적 안전성을 해석적으로 평가하기 위해서는 교량의 감쇠비를 산정하는 것이 매우 중요하다. 본 연구에서는 국내 고속 및 일반철도에서 일반적으로 사용되고 있는 소수주형강합성교, PSC Box, Steel Box, PSC, IPC, Precom, Preflex에 대하여 실내 모형실험 및 운행 중 현장계측을 하였다. 이러한 고속 및 일반철도의 대표적 교량형식에 대한 실내외 시험을 통해 대수감소율을 적용하여 감쇠비를 분석하였다. 따라서 철도교량의 감쇠비는 하중크기, 가진주파수, 진폭에 영향을 받지 않는 것으로 분석되었다. 또한, 기존 철도설계기준에 제시된 감쇠비 하한치와 비교하여 PSC구조 및 강합성구조 철도교량의 경우 감쇠비 하한값을 1.0%로 적용하는 것이 합리적이라 판단되었다.

• 한국농공학회논문집
• /
• 제50권2호
• /
• pp.19-26
• /
• 2008

This study has been carried out to investigate the dynamic characteristics of RC slabs. For this purpose, the 20-node solid element has been used to discretize the RC slabs into two parts of concrete and rebar. The material non-linearity considering elasto-visco plastic model and the smeared crack model have been adopted in the finite element formulation. The applied load can handle step load, load intensity of harmonic load, area of distributed load and frequency. The frequency of harmonic load has an significant effect on dynamic behaviour in terms of displacement. As the frequency is increased, the effect of load amplitude is more serious. Especially, if the frequency of harmonic load exceeds 30 Hz, it is noted that the displacement by harmonic load is greater than that by step load. In case of harmonic load, the damping effect shows no certain tendency with respect to frequency of load. In details, the damping is effective when the frequency of harmonic load is 2 Hz, but there is no consistent tendency according to damping ratio. The dynamic response when the frequency of harmonic load is 3 Hz shows same result for undamped case as well as for damped case with 5% damping ratio. It is also noted that we can get the largest deflection for damped case with 1% damping ratio. However, there is not any damping effect when the frequency of harmonic load is greater than 4 Hz.

• 한국농공학회지
• /
• 제42권5호
• /
• pp.151-159
• /
• 2000

Dynamic loading of structures often causes excursions of stresses will into the inelastic range and the influence of geometry changes on the response is also significant in may cases. In general , the shell structures designed according to quasi-Static analysis may collapse under condition of dynamic loading. Therefore, for a more realistic prediction on the lad carrying capacity of these shell. both material and geometric nonlinear effects should be considered. In this study , the material nonlinearity effect on the dynamic response is formulated by the elasto-viscoplastic model highly corresponding to the real behavior of the material. Also, the geometrically nonlinear behavior is taken into account using a Total Lagrangian formulation. the reinforcing bars are modeled by the equivalent steel layer at the location of reinforcements, and Von Mises yield criteria is adopted for the steel layer behavior. Also, Drucker-Prager yield criteria is applied for the behavior of concrete. the shape imperfection of dome is assumed as 'dimple type' which can be expressed Wd1=Wd0(1-(r-a)m)n while the shape imperfection of wall is assumed as sinusoidal curve which is Wwi =Wwo sin(n $\pi$y/l). In numerical test, three cases of shape imperfection of 0.0 -5.0cm(opposite direction to loading ; inner shape imperfection)and 5cm (direction to loading : outward shape imperfection) and thickness of steel layer determined by steel ratio of 0,3, and 5% were analyzed. The effect of shape imperfection and steel ratio and behavior characteristics of perfect shape shell and imperfect shape shell are identified through analysis of above mentioned numerical test. Dynamic behaviors of dome and wall according toe combination of shape imperfection and steel ratio are also discussed in this paper.