• Structural Engineering and Mechanics
• /
• 제84권5호
• /
• pp.675-684
• /
• 2022

The conventional single-degree-of-freedom (SDOF) system is appropriate for dynamic response analysis of paneltype structures without an opening. However, the typical building structures usually have four-sided fixed walls having an opening. Therefore, it may induce a considerable error when dynamic responses are estimated based on the conventional SDOF system, since the SDOF system cannot consider the effect of an opening during the SDOF analysis. For this reason, this study proposes a new SDOF system to consider the effect of an opening by adjusting its load-mass factor. The load-mass factor can be modified based on the assumption that the behaviors of the four-sided fixed wall with an opening is very similar to the behaviors of the same size wall without an opening, when the uniformly distributed blast loaded area is identical. In order to confirm a feasibility of the proposed SDOF system, a series of numerical simulations were carried out for the four-sided fixed reinforced concrete (RC) wall under a blast load. The dynamic responses estimated from the proposed SDOF system and the conventional SDOF system were compared with the dynamic responses evaluated from the finite element (FE) analysis. Especially, for the maximum dynamic responses except for 50% opening case, the proposed SDOF system had about 1.1% to 25.7% normalized errors while the conventional SDOF system had about 4.1% to 49.1% normalized errors.

• 전기학회논문지P
• /
• 제67권4호
• /
• pp.208-213
• /
• 2018

In this paper, we studied the control strategy of applying STATCOM(static synchronous compensator) to mitigate the FIDVR(fault induced delayed voltage recovery) phenomenon. The proportion of motor loads is gradually increasing which might affect power system stability. Excessive reactive power consumption by the stall of the motor loads causes FIDVR phenomenon. In addition, the low inertia of the small HVAC(heating, ventilation and air conditioner) unit will not separate itself in the event of a contingency, causing system instability. For this reason, we have developed a control strategy that utilizes STATCOM efficiently through static and dynamic analysis. Case studies on a Korean power system have validated the performance of the proposed scheme under severe contingency scenarios. The results have verified that the proposed strategy can effectively mitigate FIDVR and improve the stability and reliability of the system.

• 대한전기학회논문지:전력기술부문A
• /
• 제50권3호
• /
• pp.140-145
• /
• 2001

The instantaneous voltage drop is occurred when the fault is happened on the nearby feeders. The instantaneous voltage drop is continued during relatively short period. But, the effect of it can be very severe to some sensitive devices. That is, it can be the reason of restart or malfunction of some devices. And these phenomenons can cause the enormous economical damage and shorten the lifetime of the devices. In this paper, the device which can compensate the instantaneous voltage drop, is studied. Through the computer simulation using PSCAD/EMTDC, the validity of the control algorithm using peak detection method is verified. And the Dynamic Voltage Restorer(DVR) prototype is designed and constructed. Through the experiment, the function and performance of the DVR prototype is verified.

• Structural Engineering and Mechanics
• /
• 제20권4호
• /
• pp.389-403
• /
• 2005

In the present paper it is aimed to perform the stochastic dynamic analysis of fluid and fluidstructure systems by using the Lagrangian approach. For that reason, variable-number-nodes twodimensional isoparametric fluid finite elements are programmed in Fortran language by the authors and incorporated into a general-purpose computer program for stochastic dynamic analysis of structure systems, STOCAL. Formulation of the fluid elements includes the effects of compressible wave propagation and surface sloshing motion. For numerical example a rigid fluid tank and a dam-reservoir interaction system are selected and modeled by finite element method. Results obtained from the modal analysis are compared with the results of the analytical and numerical solutions. The Pacoima Dam record S16E component recorded during the San Fernando Earthquake in 1971 is used as a ground motion. The mean of maximum values of displacements and hydrodynamic pressures are compared with the deterministic analysis results.

• 한국자동차공학회논문집
• /
• 제10권2호
• /
• pp.201-211
• /
• 2002

In this research, we are trying to research about hydraulic system design and vehicle dynamic modeling far the development of the tire roller. The reason why we would like develop it is that tire roller is one of the most useful machine for the road construction site and application other construction equipments. Here, we conceptualize the new hydraulic system and derive the equations of motion fur dynamic analysis and also investigate system modeling by using a DAQ board. We design the hydraulic circuit of steering and traction mechanism system. This design can be used to create virtual prototypes of construction equipment. So, we studied tire roller to integrate development technology. In system analysis, we formulate hydraulic traction system model and hydraulic steering system model. Also, we integrate DAQ system to acquire experimental results in real tire roller equipment.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1998년도 춘계학술대회 논문집
• /
• pp.135-142
• /
• 1998

The performances of cutting process is mostly affected by the characteristics of closed loop system constructed with machine tool structure, work piece and tools. The chucking system is very important component in this system to hold work piece correctly in various static and dynamic load condition. Therefore, chucking force and accuracy must be considered carefully, from these reason, this paper describes the stability of chucking system which preserve high stiffness and accuracy of machine tool system.

• Journal of Advanced Marine Engineering and Technology
• /
• 제24권1호
• /
• pp.82-87
• /
• 2000

The component mode synthesis method(CMS) used for vibration analysis has demerit that error becomes larger, as degree of natural frequency grows higher. The reason of error occurrence is that Guyan's static reduction is used and the number of modes taken in each component is deficient. This paper proposes the substructure synthesis method using dynamic reduction to solve the problem from the component mode synthesis method. Computer simulation for the proposed method. FEM and the component mode synthesis method(CMS) on a rectrangular plate has been carried out to prove the avilability of the proposed method.

• 한국지진공학회논문집
• /
• 제3권4호
• /
• pp.95-100
• /
• 1999

암석 코아의탄성계수 측정에 동적방법은 잘 사용되지 않을뿐만아니라 그 값은 설계에 많이 사용되지 않는다 그이유는 동적으로 결정한 탄성계수 값이 정적으로 결정된 값보다 매우 큰 것 (약 10배)으로 인식되기 때문이다. 이논문에서는 암석 코아의 동적과 정적 시험결과를 제시하였다 도출괸 결과는 :1) 실내탄성파시험으로 매우 일관성 있는 탄성계수가 결정되고 2) 변형율에 따른 암석 코아의 비선형 변형특성의 잠정적 모델이 제시되었다.

• 한국생산제조학회지
• /
• 제18권6호
• /
• pp.642-651
• /
• 2009

The history of excavator design is not long enough which still causes most of the design considerations to be focused on static analysis or simple functional improvement based on static analysis. However, the real forces experiencing on each component of excavator are highly transient and impulsive. Therefore, the prediction and the evaluation of the movement of the excavator by dynamic load in the early design stage through the dynamic transient analysis of the excavator and ensuring of design technique plays an importance role to reduce development-cost, shorten product-deliver, decrease vehicle-weight and optimize the system design. In this paper, Commercial software DADS and ANSYS help to develop the track model of the crawler type excavator, and to evaluate the performance and the dynamic characteristics of excavator with various simulations. For that reason, the track of crawler type excavator is modelled with DADS Track Vehicle Superelement, and the reaction forces on the track rollers were predicted through the driving simulation. Also, the upper frame and cabin vibration characteristics, at the low RPM idle state, were evaluated with engine rigid body modelling. And flexibility body effects were considered to determine the more accurate joint reaction forces and accelerations under the upper frame swing motion.

• 한국CDE학회논문집
• /
• 제15권3호
• /
• pp.204-211
• /
• 2010

Recently, business process management has become an important concept to define and execute business process. During the execution of the collaborative business processes defined by the consensus with manufacturing enterprises, a lot of variations can be occurred by various internal and external factors related to business. From this reason, manufacturing enterprises have tried to seek for a technology to define and execute the collaborative business process systematically under the dynamic situations approving process variation. This study defines the collaborative business process among manufacturing enterprises at first and proposes its execution technology under the dynamic situations. Here, the proposed execution technology includes the authority management of each process, sub-process, and activity for security, the forced execution of the incomplete process containing the undefined sub-process, the re-execution in a certain range of business process for correcting errors, and the dynamic selection of sub-process. Furthermore, this study implements a prototype system to check the validity of its application under the dynamic situations.